Important!

This replacement procedure can be used for:
PEUGEOT 307 CC (3B) 2.0 16V, PEUGEOT 307 CC (3B) 2.0 16V, PEUGEOT 307 CC (3B) 1.6 16V, PEUGEOT 307 CC (3B) 2.0 16V, PEUGEOT 307 CC (3B) 2.0 HDi 135 … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Suspension Ball Joint for 307 CC (3B) and other PEUGEOT models

Ball Joint

        Ball Joint for 307 CC (3B) Petrol (136 hp)
      
        Ball Joint for 307 CC (3B) Petrol (177 hp)
      
        Ball Joint for 307 CC (3B) Petrol (110 hp)
      
        Ball Joint for 307 CC (3B) Petrol (140 hp)
      
        Ball Joint for 307 CC (3B) Diesel (136 hp)

Replacement: ball joint – PEUGEOT 307 CC (3B). Tools you need:

                        Wire brush
                      
                        WD-40 spray
                      
                        Brake cleaner 
                      
                        Copper grease 
                      
                        Torque wrench
                      
                        Combination spanner #18
                      
                        Drive socket # 18 
                      
                        Drive socket # 21 
                      
                        Drive socket # 36 
                      
                        Drive socket # 41 
                      
                        Wheel impact socket #17
                      
                        Ratchet wrench
                      
                        Tap wrench
                      
                        Hammer
                      
                        Flat chisel
                      
                        Pin punch
                      
                        Crow bar
                      
                        Ball joint puller
                      
                        Hydraulic transmission jack
                      
                        Wheel chock

Buy tools

Replacement: ball joint – PEUGEOT 307 CC (3B). AUTODOC experts recommend:

The replacement procedure is identical for the left and right ball joints.
All work should be done with the engine stopped.

Replacement: ball joint – PEUGEOT 307 CC (3B). Use the following procedure:

Step 1

Secure the wheels with chocks.
Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 3

Raise the front of the car and secure on supports.

Step 4

Unscrew the wheel bolts.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. PEUGEOT 307 CC (3B)
Step 5

Remove the wheel.
Step 6

Clean the CV axle nut cotter pin. Use a wire brush.
Step 7

Remove the CV axle nut cotter pin. Use a pin punch.
Step 8

Clean the fastener of the driveshaft. Use a wire brush. Use WD-40 spray.
Step 9

Loosen the fastener of the driveshaft. Use a drive socket #36. Use a ratchet wrench.
Step 10

Clean all joints of the arm. Use a wire brush. Use WD-40 spray.
Step 11

Unscrew the fastener connecting the ball joint to the suspension control arm. Use a drive socket #21. Use a tap wrench.
Step 12

Disconnect the spherical joint from the arm. Use a ball joint puller.
Step 13

Prop up the steering knuckle. Use a hydraulic transmission jack.
Step 14

Disconnect the spherical joint from the arm. Use a crowbar.
Step 15

Remove the support from under the steering knuckle.

Replacement: ball joint – PEUGEOT 307 CC (3B). AUTODOC recommends:
Lower the hydraulic transmission jack smoothly, without jerks, to avoid damaging assemblies and mechanisms.
Step 16

Remove the ball joint lock nut. Use a crowbar.
Step 17

Clean the fastener connecting the ball joint to the steering knuckle. Use a wire brush. Use WD-40 spray.
Step 18

Unstake the ball joint. Use a flat metal-working chisel. Use a hammer.
Step 19

Unscrew the ball joint fastening to the steering knuckle. Use a drive socket #41. Use a ratchet wrench.
Step 20

Remove the ball joint.
Step 21

Clean the ball joint mounting seat. Use a wire brush. Use WD-40 spray.
Step 22

Install a new ball joint.

Replacement: ball joint – PEUGEOT 307 CC (3B). Tip from AUTODOC:
Do not damage the ball joint cover.
Step 23

Tighten the ball joint fastener. Use a drive socket #41. Use a torque wrench. Tighten it to 230 nm torque.
Step 24

Stake the ball joint. Use a flat metal-working chisel. Use a hammer.
Step 25

Install the ball joint lock nut. Use a crowbar.
Step 26

Unscrew the lower fastener connecting the shock strut to the steering knuckle. Use a combination spanner #18. Use a drive socket #18. Use a ratchet wrench.
Step 27

Prop up the steering knuckle. Use a hydraulic transmission jack.

Step 28

Remove the fastening bolts.
Step 29

Disconnect the steering knuckle from the shock absorber strut.
Step 30

Attach the ball joint to the control arm.
Step 31

Remove the support from under the steering knuckle.

AUTODOC recommends:
PEUGEOT 307 CC (3B) – Do not lower the transmission jack sharply to avoid damaging components and mechanisms of the car.
Step 32

Fix the shock absorber strut on the steering knuckle.
Step 33

Install the fastening bolts.
Step 34

Screw in the fastener that connects the shock strut to the steering knuckle. Use a combination spanner #18. Use a drive socket #18. Use a ratchet wrench.
Step 35

Tighten the lower fasteners connecting the shock strut to the steering knuckle. Use a combination spanner #18. Use a drive socket #18. Use a torque wrench. Tighten it to 90 Nm torque.
Step 36

Tighten the drive shaft nut. Use a drive socket #36. Use a torque wrench. Tighten it to 280 Nm torque.
Step 37

Install the CV axle nut cotter pin. Use a crowbar. Use a hammer.
Step 38

Screw the fasteners of the ball joint. Use a drive socket #21. Use a ratchet wrench.
Step 39

Tighten the ball joint fastener. Use a drive socket #21. Use a torque wrench. Tighten it to 50 nm torque.
Step 40

Treat the fasteners of the ball joint. Treat the shock strut fasteners. Use copper grease.
Step 41

Clean the wheel rim mounting seat. Use a wire brush.
Step 42

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 43

Clean the brake disk surface. Use a brake cleaner.

Replacement: ball joint – PEUGEOT 307 CC (3B). Tip:
After applying the spray, wait a few minutes.
Step 44

Install the wheel.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. PEUGEOT 307 CC (3B)
Step 45

Screw in the wheel bolts. Use wheel impact socket #17.
Step 46

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #17. Use a torque wrench. Tighten it to 100 Nm torque.
Step 47

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Searching for the right tyres?

Find out which tyre and wheel sizes are compatible with the PEUGEOT 307 CC (3B) model.

Browse tyres

How to change front wheel bearing on PEUGEOT 307 CC (3B) – replacement guide

Free download PDF
5.98 MB
How to change track rod end on PEUGEOT 307 CC (3B) – replacement guide

Free download PDF
1.44 MB
How to change front anti roll bar links on PEUGEOT 307 CC (3B) – replacement guide

Free download PDF
1.33 MB
How to change front lower arm on PEUGEOT 307 CC (3B) – replacement guide

Free download PDF
2.94 MB
How to change rear wheel bearing on PEUGEOT 307 CC (3B) – replacement guide

Free download PDF
2.15 MB
How to change rear brake pads on PEUGEOT 307 CC (3B) – replacement guide

Free download PDF
2.47 MB

How to change front ball joint on Peugeot 307 SW – replacement guide

Free download PDF
2.38 MB
How to change front ball joint on PEUGEOT 307 Hatchback (3A/C) – replacement guide

Free download PDF
2.46 MB
How to change front ball joint on PEUGEOT 307 Estate (3E) – replacement guide

Free download PDF
2.46 MB
How to change ball joint on a car – replacement tutorial

Universal

Free download PDF
2.05 MB
How to change front ball joint on PEUGEOT 3008 I (0U_) – replacement guide

Free download PDF
2.46 MB
How to change front ball joint on PEUGEOT 5008 I (0U_, 0E_) – replacement guide

Free download PDF
2.46 MB

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!

Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.

Scan

To download the app:

- scan the QR code
- download from App Store
- download from Google Play

Important differences between car tools | AUTODOC tips

7K views

Published on: 16/12/2021
How to polish an old engine valve cover to a shiny finish | AUTODOC Tips

8K views

Published on: 30/11/2023
How to unlock your car without a key | AUTODOC tips

847K views

Published on: 15/09/2022
How to paint a brake caliper | AUTODOC tips

10K views

Published on: 08/04/2021