
Disclaimer
How to change front anti roll bar links on VW T-Roc (A11) – replacement guide
downloads:
1
Views:
10
Important!
This replacement procedure can be used for:
VW T-Roc (A11) 2.0 TSI 4motion, VW T-Roc (A11) 1.0 TSI, VW T-Roc (A11) 2.0 TDI 4motion, VW T-Roc (A11) 1.5 TSI, VW T-Roc (A11) 2.0 TDI, VW T-Roc (A11) 1.6 TDI, VW T-Roc (A11) 1.5 TSI 4motion, VW T-Roc (A11) 2.0 TDI 4motion, VW T-Roc (A11) 2.0 R 4motion, VW T-Roc (A11) 1.4 TSI, VW T-Roc (A11) 1.0 TSI, VW T-Roc (A11) 2.0 TDI SCR … View more
The steps may slightly vary depending on the car design.
VW T-Roc (A11) 2.0 TSI 4motion, VW T-Roc (A11) 1.0 TSI, VW T-Roc (A11) 2.0 TDI 4motion, VW T-Roc (A11) 1.5 TSI, VW T-Roc (A11) 2.0 TDI, VW T-Roc (A11) 1.6 TDI, VW T-Roc (A11) 1.5 TSI 4motion, VW T-Roc (A11) 2.0 TDI 4motion, VW T-Roc (A11) 2.0 R 4motion, VW T-Roc (A11) 1.4 TSI, VW T-Roc (A11) 1.0 TSI, VW T-Roc (A11) 2.0 TDI SCR … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Anti Roll Bar Links for T-Roc (A11) and other VW models
Anti-roll bar link
Alternative products

Wire brush
WD-40 spray
Brake cleaner
Copper grease
Torque wrench
Combination spanner #18
Drive socket # 18
XZN socket bit # 6
Wheel impact socket #17
Ratchet wrench
Wheel chock
AUTODOC recommends:
- Replace the stabiliser links on VW T-ROC (A11) in pairs.
- The replacement procedure is identical for both stabiliser links on the same axle.
- Please note: all work on the car – VW T-ROC (A11) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1Secure the wheels with chocks.Step 2Loosen the wheel mounting bolts. Use wheel impact socket #17.
- Step 3Raise the front of the car and secure on supports.Step 4Unscrew the wheel bolts.AUTODOC recommends:Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. VW T-ROC (A11)
- Step 5Remove the wheel.
- Step 6Clean all joints of the stabiliser link. Use a wire brush. Use WD-40 spray.
- Step 7Unscrew the fastener connecting the stabilizer link to the shock strut. Use a drive socket #18. Use a ratchet wrench.
- Step 8Unscrew the fastener connecting the stabilizer link to the stabilizer bar. Use a combination spanner #18. Use XZN #6. Use a ratchet wrench.
- Step 9Remove the stabilizer rod.
- Step 10Clean the mounting seats of the stabiliser link. Use a wire brush. Use WD-40 spray.
- Step 11Ιnstall the transverse stabilizer link.
- Step 12Tighten the stabiliser link fastener. Use a combination spanner #18. Use XZN #6. Use a ratchet wrench.
- Step 13Tighten the fastener connecting the stabilizer link to the shock strut. Use a combination spanner #18. Use a drive socket #18. Use XZN #6. Use a torque wrench. Tighten it to 55 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the VW T-Roc (A11) model
Popular maintenance tutorials for VW T Roc A11
Complete guides for changing the Drop links on different VW T-ROC models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your VW T-Roc (A11)
View more
- Why Checking Your Oil is Crucial for Engine Performance
- 5 possible reasons why your car heater isn't working
- How to Swap an M50 Engine in a BMW E30 Turbo | AUTODOC Project
- How to remove scratches from car plastic | AUTODOC tips
Most commonly replaced car parts on VW T-ROC
Time to replace parts? Get even better deals in our Shop app.

SCAN ME