Disclaimer
How to change front anti roll bar links on VW T-Roc Convertible (AC7) – replacement guide
downloads:
0
Views:
5
Important!
This replacement procedure can be used for:
VW T-Roc Convertible (AC7) 1.5 TSI, VW T-Roc Convertible (AC7) 1.0 TSI … View more
The steps may slightly vary depending on the car design.
VW T-Roc Convertible (AC7) 1.5 TSI, VW T-Roc Convertible (AC7) 1.0 TSI … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Anti Roll Bar Links for T-Roc Convertible (AC7) and other VW models
Alternative products

Wire brush
WD-40 spray
Brake cleaner
Copper grease
Torque wrench
Combination spanner #18
Drive socket # 18
XZN socket bit # 6
Wheel impact socket #17
Ratchet wrench
Wheel chock
AUTODOC recommends:
- Replace the stabiliser links on VW T-Roc Cabrio (AC7) in pairs.
- The replacement procedure is identical for both stabiliser links on the same axle.
- Please note: all work on the car – VW T-Roc Cabrio (AC7) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1Secure the wheels with chocks.Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #17. - Step 3Raise the front of the car and secure on supports.Step 4
Unscrew the wheel bolts.AUTODOC recommends:Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. VW T-Roc Cabrio (AC7) - Step 5
Remove the wheel. - Step 6
Clean all joints of the stabiliser link. Use a wire brush. Use WD-40 spray. - Step 7
Unscrew the fastener connecting the stabilizer link to the shock strut. Use a drive socket #18. Use a ratchet wrench. - Step 8
Unscrew the fastener connecting the stabilizer link to the stabilizer bar. Use a combination spanner #18. Use XZN #6. Use a ratchet wrench. - Step 9
Remove the stabilizer rod. - Step 10
Clean the mounting seats of the stabiliser link. Use a wire brush. Use WD-40 spray. - Step 11
Ιnstall the transverse stabilizer link. - Step 12
Tighten the stabiliser link fastener. Use a combination spanner #18. Use XZN #6. Use a ratchet wrench. - Step 13
Tighten the fastener connecting the stabilizer link to the shock strut. Use a combination spanner #18. Use a drive socket #18. Use XZN #6. Use a torque wrench. Tighten it to 55 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the VW T-Roc Convertible (AC7) model
Popular maintenance tutorials for VW T-Roc Cabrio (AC7)
Complete guides for changing the Drop links on different VW T-ROC models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your VW T-Roc Convertible (AC7)
View more
How to Safely Wash Your Car in Winter Without Damage | AUTODOC tips
DIY alternator repair | AUTODOC tips
How to Install a New Windscreen Yourself | AUTODOC Expert Tips
Unveiling the secrets: Detecting vacuum leaks with a Smoke Machine | AUTODOC
Most commonly replaced car parts on VW T-ROC
Time to replace parts? Get even better deals in our Shop app.

SCAN ME





























