Recommended replacement interval for the part category Oil filter : 12 month / 15000 km

Important!

This replacement procedure can be used for:
CITROËN Berlingo Van (K9) PureTech, CITROËN Berlingo Van (K9) PureTech … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Oil Filter for Berlingo Van (K9) and other CITROËN models

Alternative products

Oil filter

Replacement: engine oil and filter – CITROËN BERLINGO (K9). List of the tools you'll need:

                      Wire brush
                    
                      All-purpose cleaning spray
                    
                      Oil filter cup socket 74/76-15F
                    
                      Drive socket # 21 
                    
                      Ratchet wrench
                    
                      Torque wrench
                    
                      Oil drain pan
                    
                      Funnel
                    
                      Fender cover

Buy tools

Replacement: engine oil and filter – CITROËN BERLINGO (K9). Tip from AUTODOC:

Replace the oil filter every time when changing motor oil.
All work should be done with the engine stopped.
Wear gloves to prevent contact with hot liquid.

Replacement: engine oil and filter – CITROËN BERLINGO (K9). Recommended sequence of steps:

Step 1

Open the hood.

Step 2

Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.

Step 3

Unscrew the oil filler plug.
Step 4

Unscrew the oil filter. Use the 74/76-15F socket.
Step 5

Prepare a container for the old oil filter. Put the old oil filter in the container.

Replacement: engine oil and filter – CITROËN BERLINGO (K9). AUTODOC experts recommend:
Move up the container. The oil starts to drain out of the drainage hole immediately after you have removed the oil filter.
Step 6

Lift the car using a jack or place it over an inspection pit.

Replacement: engine oil and filter – CITROËN BERLINGO (K9). AUTODOC recommends:
The vehicle must be on even keel, and if it is at an angle, the drain plug must be at the lowest point.All work should be done with the engine stopped.
Step 7

Put a waste oil container with at least 5 l capacity under the drainage hole.
Step 8

Clean the area of the oil pan drainage hole. Use a wire brush. Use all-purpose cleaning spray.
Step 9

Unscrew the drain plug. Use a drive socket #21. Use a ratchet wrench.
Step 10

Drain the used oil.

Replacement: engine oil and filter – CITROËN BERLINGO (K9). Professionals recommend:
Caution! The oil may be hot.
Step 11

Wait until the oil has completely drained from the drainage hole.

Step 12

Clean the area of the oil pan drainage hole.
Step 13

Screw in the new drainage plug and tighten it. Use a drive socket #21. Use a torque wrench. Tighten it to 34 Nm torque.
Step 14

Clean the area of the oil pan drainage hole. Use all-purpose cleaning spray.
Step 15

Lower the car.

Step 16

Lubricate the rubber seal of the new filter with a little amount of fresh oil.
Step 17

Screw the new filter into its place. Use the 74/76-15F socket. Use a torque wrench. Tighten it to 25 Nm torque.
Step 18

Remove the oil filler cap. Insert the funnel.
Step 19

Pour new oil into the engine in the amount recommended by the car manufacturer.

Replacement: engine oil and filter – CITROËN BERLINGO (K9). Tip:
Use the oil recommended by the manufacturer.
Step 20

Check the oil level using the dipstick. Top up oil if necessary.

Please note!
The oil level should be between the Min and Max marks.
Step 21

Install the oil filler cap.

Step 22

Tighten the oil filler cap.
Step 23

Run the engine for a few minutes. After the oil pressure warning light goes out, stop the engine.
Step 24

Check the oil level 5 minutes after the stop of the engine operation using a dipstick and add oil if necessary.

Please note!
The oil level should be between the Min and Max marks.Make sure that the oil filler cap is properly tightened.Check the threaded plug of the drainage hole and the oil filter seal for tightness. If necessary, carefully tighten them up.
Step 25

Remove the fender protection cover.

Step 26

Close the hood.

Replacement: engine oil and filter – CITROËN BERLINGO (K9). Tip from AUTODOC experts:
Note that oil pressure warning light, which indicates insufficient pressure in the lubrication system, may be on for a longer time than usual. After a few seconds, the oil will fill all the channels, and the light will go out. To protect the environment from pollution, be sure to dispose of the used filters at special collection points.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the CITROËN Berlingo Van (K9) model

CITROËN BERLINGO (K9) tyre size

How to change fuel filter on CITROËN Berlingo Van (K9) – replacement guide

Free download PDF
931.84 KB
How to change front windshield wipers on CITROËN Berlingo Van (K9) – replacement guide

Free download PDF
706.56 KB
How to change front anti roll bar links on CITROËN Berlingo Van (K9) – replacement guide

Free download PDF
1.34 MB
How to change serpentine belt on Citroen Xsara Picasso – replacement guide

Free download PDF
1.72 MB
How to change serpentine belt on Citroen C3 1 – replacement guide

Free download PDF
1.02 MB
How to change engine oil and filter on Citroen C3 1 – replacement guide

Free download PDF
1.65 MB

How to change engine oil and filter on Citroën Berlingo M – replacement guide

Free download PDF
2.3 MB
How to change engine oil and filter on CITROËN BERLINGO (B9) – replacement guide

Free download PDF
1.17 MB
How to change engine oil and filter on CITROËN BERLINGO Box (B9) – replacement guide

Free download PDF
1.17 MB
How to change engine oil and filter on CITROËN Berlingo / Berlingo First (MF, GJK, GFK) – replacement guide

Free download PDF
1.18 MB
How to change engine oil and filter on CITROËN Berlingo (K9) – replacement guide

Free download PDF
1.17 MB
How to change engine oil and filter on a car – replacement tutorial

Universal

Free download PDF
2.82 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

How to replace a timing chain yourself

19K views

Published on: 12/12/2024
Initial Car Inspection: What to Check Before You Buy

5K views

Published on: 24/10/2020
5 tools that make car repair incredibly simple | AUTODOC tips

47K views

Published on: 25/01/2024
#DIY Wheel Rim Restoration: Revive Scratches and Chips Easily!

7K views

Published on: 18/07/2024