Disclaimer
How to change front anti roll bar links on AUDI A1 Citycarver (GBH) – replacement guide
downloads:
0
Views:
1
Important!
This replacement procedure can be used for:
AUDI A1 Citycarver (GBH) 25 TFSI, AUDI A1 Citycarver (GBH) 30 TFSI, AUDI A1 Citycarver (GBH) 35 TFSI, AUDI A1 Citycarver (GBH) 30 TFSI … View more
The steps may slightly vary depending on the car design.
AUDI A1 Citycarver (GBH) 25 TFSI, AUDI A1 Citycarver (GBH) 30 TFSI, AUDI A1 Citycarver (GBH) 35 TFSI, AUDI A1 Citycarver (GBH) 30 TFSI … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Anti Roll Bar Links for A1 Citycarver (GBH) and other AUDI models
Wire brush
WD-40 spray
Brake cleaner
Copper grease
Combination spanner #17
Drive socket # 16
Drive socket # 17
HEX bit No.H5.
Wheel impact socket #17
Ratchet wrench
Torque wrench
Wheel chock
Replacement: anti roll bar links – AUDI A1 Citycarver (GBH). AUTODOC experts recommend:
- Replace the stabiliser links on AUDI A1 Citycarver (GBH) in pairs.
- The replacement procedure is identical for both stabiliser links on the same axle.
- All work should be done with the engine stopped.
Replacement: anti roll bar links – AUDI A1 Citycarver (GBH). Recommended sequence of steps:
- Step 1
Secure the wheels with chocks. - Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #17. - Step 3Raise the rear of the car and secure on supports.Step 4
Unscrew the wheel bolts.AUTODOC recommends:Important! Hold the wheel while unscrewing the fastening bolts. AUDI A1 Citycarver (GBH) - Step 5
Remove the wheel. - Step 6
Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray. - Step 7
Unscrew the fastener connecting the stabilizer link to the stabilizer bar. Use a drive socket #16. Use a ratchet wrench. - Step 8
Unscrew the fastener connecting the stabilizer link to the shock strut. Use a drive socket #16. Use a ratchet wrench. - Step 9
Remove the stabilizer rod.Replacement: anti roll bar links – AUDI A1 Citycarver (GBH). Tip from AUTODOC experts:Examine stabiliser bushes. Replace them if needed. - Step 10
Clean the mounting seats of the stabiliser link. Use a wire brush. Use WD-40 spray. - Step 11
Install a new rod, tighten the fasteners. Use a combination spanner #17. Use HEX No.H5.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Searching for the right tyres?
Find out which tyre and wheel sizes are compatible with the AUDI A1 Citycarver (GBH) model.
Popular maintenance tutorials for AUDI A1 Citycarver (GBH)
Free download PDF
1.37 MB
Free download PDF1.27 MB
Free download PDF1.5 MB
Free download PDF1.39 MB
Free download PDF512 KB
Free download PDF768 KB
Complete guides for changing the Drop links on different AUDI A1 models
Free download PDF1.36 MB
Free download PDF1.17 MB
Free download PDF1.37 MB
Free download PDF1.17 MB
Free download PDF1.24 MB
Free download PDF972.8 KB
Your profile is your personal assistant.
It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents
Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
Scan
To download the app:
- - scan the QR code
- - download from App Store
- - download from Google Play
Tips & tricks for your AUDI A1 Citycarver (GBH)
View more
5 tools that make car repair incredibly simple | AUTODOC tips
How to remove scratches from car plastic | AUTODOC tips
How to clean an engine bay | AUTODOC
4 reasons why your CHECK ENGINE light is on | AUTODOC tips
