Disclaimer
How to change rear anti roll bar links on AUDI A1 Hatchback (8X1, 8XK) – replacement guide
downloads:
7
Views:
106
Important!
This replacement procedure can be used for:
AUDI A1 Hatchback (8X1, 8XK) S1 quattro, AUDI A1 Hatchback (8X1, 8XK) 2.0 TFSI quattro … View more
The steps may slightly vary depending on the car design.
AUDI A1 Hatchback (8X1, 8XK) S1 quattro, AUDI A1 Hatchback (8X1, 8XK) 2.0 TFSI quattro … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Anti Roll Bar Links for A1 Hatchback (8X1, 8XK) and other AUDI models
Alternative products

Wire brush
WD-40 spray
Brake cleaner
Copper grease
Combination spanner #14
Combination spanner #16
HEX bit No.H5.
XZN socket bit # 6
Drive socket # 14
Wheel impact socket #17
Ratchet wrench
Torque wrench
Hydraulic transmission jack
Wheel chock
Replacement: anti roll bar links – AUDI A1 (8X1, 8XF). AUTODOC recommends:
- Replace the stabiliser links on AUDI A1 (8X1, 8XF) in pairs.
- The replacement procedure is identical for both stabiliser links on the same axle.
- All work should be done with the engine stopped.
Replacement: anti roll bar links – AUDI A1 (8X1, 8XF). Use the following procedure:
- Step 1
Secure the wheels with chocks. - Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #17. - Step 3Raise the rear of the car and secure on supports.Step 4
Unscrew the wheel bolts.Replacement: anti roll bar links – AUDI A1 (8X1, 8XF). Tip:To avoid injury, hold up the wheel when unscrewing the bolts. - Step 5
Remove the wheel. - Step 6
Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray. - Step 7
Unscrew the fastener connecting the stabilizer bar with the control arm. Use a combination spanner #16. Use XZN #6. Use a ratchet wrench. - Step 8
Unscrew the fasteners connecting the stabiliser link to the stabiliser bar. Use a combination spanner #16. Use XZN #6. Use a ratchet wrench. - Step 9
Remove the stabilizer rod.Replacement: anti roll bar links – AUDI A1 (8X1, 8XF). Tip from AUTODOC experts:Examine stabiliser bushes. Replace them if needed. - Step 10
Clean the mounting seats of the stabiliser link. Use a wire brush. Use WD-40 spray. - Step 11
Ιnstall the transverse stabilizer link. - Step 12
Tighten the stabiliser link fastener. Use a combination spanner #14. Use HEX No.H5. Use a ratchet wrench. - Step 13
Tighten the fastener connecting the stabilizer bar with the control arm. Use a drive socket #14. Use a torque wrench. Tighten it to 45 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the AUDI A1 Hatchback (8X1, 8XK) model
Popular maintenance tutorials for Audi A1 8x
Complete guides for changing the Drop links on different AUDI A1 models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your AUDI A1 Hatchback (8X1, 8XK)
View more
Don’t Replace, Just Polish! Headlight Restoration with AUTODOC
How to easily repair a punctured tyre | AUTODOC tips
TOP 6 WD-40 lifehacks | AUTODOC tips
Engine Overheating? Replace Your Cooling Fan to Fix It
Most commonly replaced car parts on AUDI A1
Time to replace parts? Get even better deals in our Shop app.

SCAN ME




























