Disclaimer
How to change engine oil and filter on Toyota Prius 2 – replacement guide
downloads:
8
Views:
184
Recommended replacement interval for the part category Oil filter : 1 year / 15000 km
Important!
This replacement procedure can be used for:
TOYOTA PRIUS Hatchback (NHW20_) 1.5 Hybrid (NHW20_) … View more
The steps may slightly vary depending on the car design.
TOYOTA PRIUS Hatchback (NHW20_) 1.5 Hybrid (NHW20_) … View more
The steps may slightly vary depending on the car design.
How to change oil filter and engine oil on TOYOTA PRIUS 2 (NHW20) [TUTORIAL AUTODOC]

All the parts you need to replace – Oil Filter for PRIUS Hatchback (NHW20_) and other TOYOTA models
Alternative products

Wire brush
All-purpose cleaning spray
Oil filter cup socket 76-14F
Drive socket # 14
Ratchet wrench
Torque wrench
Oil drain pan
Funnel
Fender cover
Replacement: engine oil and filter – Toyota Prius 2. Tip from AUTODOC experts:
- Replace the oil filter every time when changing motor oil.
- Wear gloves to prevent contact with hot liquid.
- Please note: all work on the car – Toyota Prius 2 – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1
Open the hood. - Step 2
Use a fender protection cover to prevent damaging paintwork and plastic parts of the car. - Step 3
Unscrew the oil filler plug. - Step 4
Lift the car using a jack or place it over an inspection pit.Replacement: engine oil and filter – Toyota Prius 2. AUTODOC recommends:The vehicle must be on even keel, and if it is at an angle, the drain plug must be at the lowest point. - Step 5
Put a waste oil container with at least 5 l capacity under the drainage hole. - Step 6
Clean the area of the oil pan drainage hole. Use a wire brush. Use all-purpose cleaning spray. - Step 7
Unscrew the drain plug. Use a drive socket #14. Use a ratchet wrench. - Step 8
Drain the used oil.Replacement: engine oil and filter – Toyota Prius 2. Tip:Caution! The oil may be hot.Wait until the oil has completely drained from the drainage hole. - Step 9
Prepare a container for the old oil filter. - Step 10
Unscrew the oil filter. Use the 76-14F socket. Use a ratchet wrench. - Step 11
Put the old oil filter in the container.Replacement: engine oil and filter – Toyota Prius 2. Tip from AUTODOC experts:Move up the container. The oil starts to drain out of the drainage hole immediately after you have removed the oil filter. - Step 12
Clean the oil filter seat. Use all-purpose cleaning spray. - Step 13
Lubricate the rubber seal of the new filter with a little amount of fresh oil. - Step 14
Screw the new filter into its place. Use the 76-14F socket. Use a torque wrench. Tighten it to 23 Nm torque.Please note!Make sure to install the filter correctly. Don't mix up the sides of the part. - Step 15
Clean the area of the oil pan drainage hole. - Step 16
Screw in the new drainage plug and tighten it. Use a drive socket #14. Use a torque wrench. Tighten it to 27 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the TOYOTA Prius II Liftback (XW20) model
Popular maintenance tutorials for Toyota Prius 2
Complete guides for changing the Oil filters on different TOYOTA PRIUS models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your TOYOTA PRIUS Hatchback (NHW20_)
View more
How to restore a steering wheel | AUTODOC tips
Why does it burn oil? The main cause of oil consumption in EA888 Gen 1
5 tools that make car repair incredibly simple | AUTODOC tips
How to easily repair a punctured tyre | AUTODOC tips
Most commonly replaced car parts on TOYOTA PRIUS
Time to replace parts? Get even better deals in our Shop app.

SCAN ME


































