
Disclaimer
How to change engine oil and filter on NISSAN MICRA V (K14) – replacement guide
downloads:
78
Views:
1475

Recommended replacement interval for the part category Oil filter : 1 year / 20000 km
Important!
This replacement procedure can be used for:
NISSAN MICRA V (K14) 1.0, NISSAN MICRA V (K14) 1.0 … View more
The steps may slightly vary depending on the car design.
NISSAN MICRA V (K14) 1.0, NISSAN MICRA V (K14) 1.0 … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Oil Filter for MICRA V (K14) and other NISSAN models
Oil filter
Alternative products

All-purpose cleaning spray
Oil filter cup socket 76/14-F
Square oil drain plug socket No.8
Torque wrench
Oil drain pan
Funnel
Fender cover
AUTODOC recommends:
- Replace the oil filter every time when changing motor oil.
- Wear gloves to prevent contact with hot liquid.
- All work should be done with the engine stopped.
Replacement: engine oil and filter – NISSAN MICRA V (K14). Recommended sequence of steps:
- Step 1Open the hood.Step 2Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.Step 3Unscrew the oil filler plug.
- Step 4Lift the car using a jack or place it over an inspection pit.Replacement: engine oil and filter – NISSAN MICRA V (K14). Tip:The vehicle must be on even keel, and if it is at an angle, the drain plug must be at the lowest point.All work should be done with the engine stopped.Step 5Put a waste oil container with at least 5 l capacity under the drainage hole.
- Step 6Unscrew the drain plug. Use square oil drain plug socket No.8
- Step 7Drain the used oil.Replacement: engine oil and filter – NISSAN MICRA V (K14). Tip from AUTODOC experts:Caution! The oil may be hot.Wait until the oil has completely drained from the drainage hole.
- Step 8Move the container under the oil filter.
- Step 9Unscrew the oil filter. Use the 76/14-F socket.
- Step 10Prepare a container for the old oil filter. Put the old oil filter in the container.Replacement: engine oil and filter – NISSAN MICRA V (K14). Tip from AUTODOC:Move up the container. The oil starts to drain out of the drainage hole immediately after you have removed the oil filter.Step 11Clean the oil filter seat.
- Step 12Lubricate the rubber seal of the new filter with a little amount of fresh oil.
- Step 13Screw the new filter into its place. Use the 76/14-F socket. Use a torque wrench. Tighten it to 21 nm torque.
- Step 14Clean the oil filter seat. Use all-purpose cleaning spray.
- Step 15Clean the area of the oil pan drainage hole.
- Step 16Screw in the new drainage plug and tighten it. Use square oil drain plug socket No.8 Use a torque wrench. Tighten it to 20 nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the NISSAN Micra V Hatchback (K14) model
Popular maintenance tutorials for Nissan Micra 5
Complete guides for changing the Oil filters on different NISSAN MICRA models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your NISSAN MICRA V (K14)
View more
- DIY jack restoration | AUTODOC tips
- 5 most common causes of oil leaks | AUTODOC tips
- Drive with Care: 8 Common Bad Driving Habits Explained | AUTODOC
- Easy Steps to Paint Brake Calipers Without Special Skills or High Costs
Most commonly replaced car parts on NISSAN MICRA
Time to replace parts? Get even better deals in our Shop app.

SCAN ME