Recommended replacement interval for the part category Oil filter : 1 year / 30000 km

Important!

This replacement procedure can be used for:
FORD Tourneo Connect / Grand Tourneo Connect V408 Estate 1.5 TDCi, FORD Tourneo Connect / Grand Tourneo Connect V408 Estate 1.5 TDCi, FORD Tourneo Connect / Grand Tourneo Connect V408 Estate 1.5 TDCi, FORD Tourneo Connect / Grand Tourneo Connect V408 Estate 1.6 TDCi, FORD Tourneo Connect / Grand Tourneo Connect V408 Estate 1.6 TDCi, FORD Tourneo Connect / Grand Tourneo Connect V408 Estate 1.6 TDCi … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Oil Filter for Tourneo Connect / Grand Tourneo Connect V408 Estate and other FORD models

Oil filter

        Oil filter for Tourneo Connect / Grand Tourneo Connect V408 Estate Diesel (95 hp)
      
        Oil filter for Tourneo Connect / Grand Tourneo Connect V408 Estate Diesel (115 hp)
      
        Oil filter for Tourneo Connect / Grand Tourneo Connect V408 Estate Diesel (75 hp)
      
        Oil filter for Tourneo Connect / Grand Tourneo Connect V408 Estate Diesel (101 hp)
      
        Oil filter for Tourneo Connect / Grand Tourneo Connect V408 Estate Diesel (75 hp)
      
        Oil filter for Tourneo Connect / Grand Tourneo Connect V408 Estate Diesel (120 hp)

Replacement: engine oil and filter – FORD TOURNEO CONNECT / GRAND TOURNEO CONNECT Kombi. Tools you might need:

                        Wire brush
                      
                        All-purpose cleaning spray
                      
                        Drive socket # 7
                      
                        Drive socket # 21
                      
                        Drive socket # 27
                      
                        Ratchet wrench
                      
                        Torque wrench
                      
                        Flat Screwdriver
                      
                        Crow bar
                      
                        Oil drain pan
                      
                        Funnel
                      
                        Microfibre towel
                      
                        Fender cover

Buy tools

Replacement: engine oil and filter – FORD TOURNEO CONNECT / GRAND TOURNEO CONNECT Kombi. Professionals recommend:

Replace the oil filter every time when changing motor oil.
Wear gloves to prevent contact with hot liquid.
Please note: all work on the car – FORD TOURNEO CONNECT / GRAND TOURNEO CONNECT Kombi – should be done with the engine switched off.

Carry out replacement in the following order:

Step 1

Open the hood.

Step 2

Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.

Step 3

Unscrew the oil filler plug.
Step 4

Lift the car using a jack or place it over an inspection pit.

Replacement: engine oil and filter – FORD TOURNEO CONNECT / GRAND TOURNEO CONNECT Kombi. AUTODOC experts recommend:
The vehicle must be on even keel, and if it is at an angle, the drain plug must be at the lowest point.All work should be done with the engine stopped.
Step 5

Put a waste oil container with at least 5 l capacity under the drainage hole.
Step 6

Clean the area of the oil pan drainage hole. Use a wire brush. Use all-purpose cleaning spray.
Step 7

Unscrew the drain plug. Use a drive socket #21. Use a ratchet wrench.
Step 8

Drain the used oil.

Replacement: engine oil and filter – FORD TOURNEO CONNECT / GRAND TOURNEO CONNECT Kombi. Tip:
Caution! The oil may be hot.Wait until the oil has completely drained from the drainage hole.
Step 9

Unplug the mass air flow sensor connector.
Step 10

Detach the air intake hose clamp. Use a drive socket #7. Use a ratchet wrench.
Step 11

Remove the air intake pipe. Use a crowbar.
Step 12

Disconnect the crankcase ventilation hose from the air duct.
Step 13

Remove the air filter housing.
Step 14

Cover the air intake hose with a microfibre towel to prevent dust and dirt from getting into the system.
Step 15

Prepare a container for the old oil filter.
Step 16

Clean the oil filter housing cap. Use all-purpose cleaning spray.
Step 17

Unscrew the filter housing cap together with the old filter element. Use a drive socket #27. Use a ratchet wrench.
Step 18

Put the old oil filter in the container.

AUTODOC recommends:
Move up the container. The oil starts to drain out of the drainage hole immediately after you have removed the oil filter.
Step 19

Remove the oil filter cover O-ring. Use a flat screwdriver.
Step 20

Detach the oil filter from the filter cover.
Step 21

Clean the oil filter housing cap. Use all-purpose cleaning spray.
Step 22

Install the new oil filter to the mounting seat on the filter cover.

Replacement: engine oil and filter – FORD TOURNEO CONNECT / GRAND TOURNEO CONNECT Kombi. AUTODOC experts recommend:
Make sure to install the filter correctly. Don't mix up the sides of the part.
Step 23

Install a new O-ring to its mounting seat on the filter cover.
Step 24

Lubricate the rubber seal of the new filter with a little amount of fresh oil.
Step 25

Install a new oil filter housing cover and tighten it. Use a drive socket #27. Use a torque wrench. Tighten it to 25 Nm torque.
Step 26

Clean the oil filter housing cap. Use all-purpose cleaning spray.
Step 27

Clean the area of the oil pan drainage hole.
Step 28

Screw in the new drainage plug and tighten it. Use a drive socket #21. Use a torque wrench. Tighten it to 28 Nm torque.
Step 29

Clean the area of the oil pan drainage hole. Use all-purpose cleaning spray.
Step 30

Lower the car.

Step 31

Remove the microfibre towel from the air intake hose.
Step 32

Reinstall the air filter housing.
Step 33

Install the air intake pipe and secure it.
Step 34

Fasten the clamp on the air intake hose. Use a drive socket #7. Use a ratchet wrench.
Step 35

Connect the crankcase ventilation hose to the air duct.
Step 36

Plug in the mass air flow sensor conntector.
Step 37

Remove the oil filler cap.
Step 38

Insert the funnel.
Step 39

Pour new oil into the engine in the amount recommended by the car manufacturer.

Replacement: engine oil and filter – FORD TOURNEO CONNECT / GRAND TOURNEO CONNECT Kombi. AUTODOC recommends:
Use the oil recommended by the manufacturer.
Step 40

Check the oil level using the dipstick. Top up oil if necessary.

Please note!
The oil level should be between the Min and Max marks.
Step 41

Install the oil filler cap.
Step 42

Tighten the oil filler cap.
Step 43

Run the engine for a few minutes. After the oil pressure warning light goes out, stop the engine.

Step 44

Check the oil level 5 minutes after the stop of the engine operation using a dipstick and add oil if necessary.

Please note!
The oil level should be between the Min and Max marks.Make sure that the oil filler cap is properly tightened.Check the threaded plug of the drainage hole and the oil filter seal for tightness. If necessary, carefully tighten them up.
Step 45

Remove the fender protection cover.

Step 46

Close the hood.

Replacement: engine oil and filter – FORD TOURNEO CONNECT / GRAND TOURNEO CONNECT Kombi. Professionals recommend:
Note that oil pressure warning light, which indicates insufficient pressure in the lubrication system, may be on for a longer time than usual. After a few seconds, the oil will fill all the channels, and the light will go out. To protect the environment from pollution, be sure to dispose of the used filters at special collection points.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Searching for the right tyres?

Find out which tyre and wheel sizes are compatible with the FORD Tourneo Connect / Grand Tourneo Connect V408 Estate model.

Browse tyres

How to change fuel filter on FORD Tourneo Connect / Grand Tourneo Connect V408 Estate – replacement guide

Free download PDF
1.66 MB
How to change front brake pads on FORD Tourneo Connect / Grand Tourneo Connect V408 Estate – replacement guide

Free download PDF
2.36 MB
How to change rear brake pads on FORD Tourneo Connect / Grand Tourneo Connect V408 Estate – replacement guide

Free download PDF
1.72 MB
How to change serpentine belt on FORD Tourneo Connect / Grand Tourneo Connect V408 Estate – replacement guide

Free download PDF
768 KB
How to change front anti roll bar links on FORD Tourneo Connect / Grand Tourneo Connect V408 Estate – replacement guide

Free download PDF
1.26 MB
How to change water pump & timing belt kit on FORD Tourneo Connect / Grand Tourneo Connect V408 Estate – replacement guide

Free download PDF
7.56 MB

How to change engine oil and filter on FORD TOURNEO CONNECT – replacement guide

Free download PDF
1.42 MB
How to change engine oil and filter on a car – replacement tutorial

Universal

Free download PDF
2.82 MB
How to change engine oil and filter on Ford Focus MK2 diesel – replacement guide

Free download PDF
2.92 MB
How to change engine oil and filter on Ford Focus MK2 petrol – replacement guide

Free download PDF
2.64 MB
How to change engine oil and filter on Ford Fiesta V JH JD – replacement guide

Free download PDF
2.72 MB
How to change engine oil and filter on Ford Fiesta JA8 – replacement guide

Free download PDF
2.83 MB

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!

Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.

Scan

To download the app:

- scan the QR code
- download from App Store
- download from Google Play

How to detect vacuum leaks using a smoke machine | AUTODOC

19K views

Published on: 23/07/2020
Petrol or diesel? What's the difference between these engines? | AUTODOC

4K views

Published on: 04/05/2021
Top 5 brake repair mistakes | AUTODOC tips

184K views

Published on: 27/10/2022
DIY valve cover restoration | AUTODOC tips

6K views

Published on: 29/06/2023