Disclaimer
How to change CV joint on Audi A4 B5 saloon – replacement guide
downloads:
29
Views:
650
Important!
This replacement procedure can be used for:
AUDI A4 Saloon (8D2, B5) 1.8, AUDI A4 Saloon (8D2, B5) 1.8 T, AUDI A4 Saloon (8D2, B5) 1.9 TDI, AUDI A4 Saloon (8D2, B5) 1.8 quattro, AUDI A4 Saloon (8D2, B5) 1.8 T quattro, AUDI A4 Saloon (8D2, B5) 1.9 TDI, AUDI A4 Saloon (8D2, B5) 1.9 TDI quattro, AUDI A4 Saloon (8D2, B5) 1.9 TDI, AUDI A4 Saloon (8D2, B5) 1.8, AUDI A4 Saloon (8D2, B5) 1.8 quattro … View more
The steps may slightly vary depending on the car design.
AUDI A4 Saloon (8D2, B5) 1.8, AUDI A4 Saloon (8D2, B5) 1.8 T, AUDI A4 Saloon (8D2, B5) 1.9 TDI, AUDI A4 Saloon (8D2, B5) 1.8 quattro, AUDI A4 Saloon (8D2, B5) 1.8 T quattro, AUDI A4 Saloon (8D2, B5) 1.9 TDI, AUDI A4 Saloon (8D2, B5) 1.9 TDI quattro, AUDI A4 Saloon (8D2, B5) 1.9 TDI, AUDI A4 Saloon (8D2, B5) 1.8, AUDI A4 Saloon (8D2, B5) 1.8 quattro … View more
The steps may slightly vary depending on the car design.
How to change cv joint on AUDI A4 B5 Saloon [TUTORIAL AUTODOC]

All the parts you need to replace – CV Joint for A4 Saloon (8D2, B5) and other AUDI models
Alternative products

Wire brush
WD-40 spray
All-purpose cleaning spray
Brake cleaner
Copper grease
Torque wrench
Combination spanner #16
Drive socket # 16
Drive socket # 17
HEX bit No.H14
Wheel impact socket #17
Ratchet wrench
Bush and bearing driver set
Flat screwdriver
Tap wrench
Clic-R collar pliers
Hammer
Crow bar
Hydraulic transmission jack
Wheel chock
Replacement: CV joint – Audi A4 B5 saloon. Tip from AUTODOC:
- The CV joint replacement procedure is identical for the left and right CV axles.
- Replace the CV joints of CV axles in pairs.
- Please note: all work on the car – Audi A4 B5 saloon – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1
Secure the wheels with chocks. - Step 2
Loosen the fastener of the driveshaft. Use HEX No.H14. Use a tap wrench. - Step 3
Loosen the wheel mounting bolts. Use wheel impact socket #17. - Step 4
Raise the front of the car and secure on supports. - Step 5Unscrew the wheel bolts.AUTODOC recommends:Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. Audi A4 B5 saloonStep 6
Remove the wheel. - Step 7
Spread the brake pads. Use a crowbar. - Step 8
Clean the brake caliper bracket fasteners. Use a wire brush. Use WD-40 spray. - Step 9
Unscrew the caliper bracket fastening. Use a drive socket #17. Use a ratchet wrench. Use a tap wrench. - Step 10
Remove the brake caliper together with its bracket.Replacement: CV joint – Audi A4 B5 saloon. AUTODOC recommends:Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur.Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary. - Step 11
Remove the brake disc. - Step 12
Remove the fastening bolt. Use HEX No.H14. Use a ratchet wrench. - Step 13
Prop up the steering knuckle. Use a hydraulic transmission jack. - Step 14
Clean all joints of the arm. Use a wire brush. Use WD-40 spray. - Step 15
Unscrew the upper arm fastenings. Use a combination spanner #16. Use a drive socket #16. Use a ratchet wrench. - Step 16
Remove the fastening bolt. - Step 17Remove the control arms. Use a crowbar.Step 18
Detach the driveshaft from the steering knuckle.Replacement: CV joint – Audi A4 B5 saloon. Tip:Make sure that the drive shaft is not unloaded (when the car is jacked). - Step 19
Clean the clamps of the CV joint boot. Use a wire brush. Use WD-40 spray. - Step 20
Detach the clamps of the CV joint boot. Use a flat screwdriver. - Step 21
Install and tighten the drive shaft bolt. Use HEX No.H14. Use a ratchet wrench. - Step 22
Remove the CV joint together with its boot. - Step 23
Remove the fastening bolt. Use HEX No.H14. Use a ratchet wrench. - Step 24
Clean the CV joint mounting seat. Use all-purpose cleaning spray. - Step 25
Remove the CV joint circlip. Use a flat screwdriver. - Step 26
Clean the CV joint mounting seat. Use all-purpose cleaning spray. - Step 27
Pack the CV joint with the grease supplied in the kit. - Step 28Move the inner race of the new CV joint from side to side to get it ready to work.Step 29
Install the CV joint boot on the CV axle. Use a flat screwdriver. - Step 30
Install the CV joint circlip. - Step 31
Install the new CV joint. Use a bush and bearing driver set. Use a hammer. - Step 32
Move the inner race of the new CV joint from side to side to get it ready to work.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the AUDI A4 B5 Saloon (8D2) model
Popular maintenance tutorials for Audi A4 B5
Complete guides for changing the Constant velocity joint on different AUDI A4 models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your AUDI A4 Saloon (8D2, B5)
View more
Deep interior cleaning | Car transformation by detailing
The Ultimate Guide to Engine Bay Cleaning | AUTODOC
How I started restoring a driveshaft | Drivetrain restoration – Part 1
The Fast and Easy Way to Fix a Broken Wheel Stud | AUTODOC tips
Most commonly replaced car parts on AUDI A4
Time to replace parts? Get even better deals in our Shop app.

SCAN ME








































