Important!
This replacement procedure can be used for:
FORD TRANSIT MK-7 Box 2.2 TDCi, FORD TRANSIT MK-7 Box 2.2 TDCi, FORD TRANSIT MK-7 Box 2.2 TDCi, FORD TRANSIT MK-7 Box 2.2 TDCi, FORD TRANSIT MK-7 Box 2.4 TDCi RWD, FORD TRANSIT MK-7 Box 2.4 TDCi RWD, FORD TRANSIT MK-7 Box 2.2 TDCi, FORD TRANSIT MK-7 Box 2.4 TDCi RWD, FORD TRANSIT MK-7 Box 2.3 16V RWD, FORD TRANSIT MK-7 Box 3.2 TDCi RWD, FORD TRANSIT MK-7 Box 2.2 TDCi, FORD TRANSIT MK-7 Box 2.2 TDCi View more

The steps may slightly vary depending on the car design.

How to change a front suspension strut on the FORD TRANSIT MK7 [AUTODOC TUTORIAL]

video
All the parts you need to replace – Springs for TRANSIT MK-7 Box and other FORD models
Tools
Replacement: coil springs – Ford Transit Mk7 van. Tools you'll need:
Wire brush
WD-40 spray
All-purpose cleaning spray
Ceramic grease
Torque wrench
19 mm combination spanner
13 mm socket
15 mm socket
18 mm socket
19 mm socket
24 mm socket
36 mm socket
18 mm strut nut socket
H5 hex bit
H6 hex extension bar
21 mm wheel impact socket
Ratchet wrench or power tool for removal/installation of threaded fasteners
Tommy bar
Mounting lever
Long nose pliers
Telescoping magnetic pick-up tool
Pin punch
Hammer
Rubber mallet
Ball joint separator
Stationary spring compressor
Transmission jack or a second vehicle jack
Car lift or jack with jack stands, and wheel chocks
Replacement: coil springs – Ford Transit Mk7 van. AUTODOC recommends:
  • The struts, coil springs, and strut mounts of the front suspension should be replaced in pairs.
  • The replacement procedure is identical for the right and left struts, coil springs, and strut mounts of the front suspension, with the exception of the steps for accessing the fasteners of the left and right strut mounts.
  • Please note: all work on the car – Ford Transit Mk7 van – should be done with the engine switched off.
Carry out the replacement steps as follows:
  1. Step 1
    How to change Springs on Ford Transit Mk7 2006 - free PDF and video manuals
    Open the car door.
  2. Step 2
    How to replace FORD TRANSIT MK-7 Box 2.2 TDCi 2007 Springs - step-by-step manuals and video guides
    Open the glove box.
  3. Step 3
    Ford Transit Mk7 2.4 TDCi RWD 2008 Springs replacement: free workshop manuals
    Press down on the glove box retaining tabs to detach it.
  4. Step 4
    Changing Springs on FORD TRANSIT MK-7 Box 2.4 TDCi RWD 2009 by yourself
    Remove the glove box.
  5. Step 5
    How to remove FORD TRANSIT 2.2 TDCi 2010 Springs - online easy-to-follow instructions
    Fold back the insulation that covers the strut mount fasteners.
  6. Step 6
    How to replace Springs on FORD TRANSIT MK-7 Box 2011: download PDF manuals and video instructions
    Clean the fasteners of the top strut mount. Use a wire brush. Use WD-40 spray.
  7. Step 7
    How hard is it to do yourself: Springs replacement on Ford Transit Mk7 2.2 TDCi 2012 - download illustrated guide
    Loosen the strut mount fasteners. Use a 13 mm socket. Use a ratchet wrench.
    Warning!
    Do not unscrew the nuts completely.
  8. Step 8
    Need to know how to renew Springs on FORD TRANSIT 2013? This free workshop manual will help you to do it yourself
    Secure the wheels with chocks.
  9. Step 9
    Remove the wheel centre cap.
    Step 10
    Changing of Springs on Ford Transit Mk7 2014 won't be an issue if you follow this illustrated step-by-step guide
    Loosen the wheel nuts. Use a 21 mm wheel impact socket. Use a tommy bar.
  10. Step 11
    FORD TRANSIT 2.2 TDCi Springs replacement: online guides and video tutorials
    Remove the cotter pin that secures the axle fastener. Use a mounting lever. Use long nose pliers.
  11. Step 12
    Replacing Springs on Ford Transit Mk7 2007 2.2 TDCi by yourself
    Remove the castle cover from the axle nut.
  12. Step 13
    TRANSIT MK-7 Box 2.2 TDCi 2008 Springs DIY replacement workshop manual
    Clean the axle nut. Use a wire brush. Use WD-40 spray.
  13. Step 14
    How to change Springs on FORD TRANSIT MK-7 Box 2009 - tips and tricks
    Loosen the axle nut. Use a 36 mm socket. Use a tommy bar.
  14. Step 15
    Step-by-step recommendations for DIY replacement Ford Transit Mk7 2010 2.2 TDCi Springs
    Raise the vehicle.
    Replacement: coil springs – Ford Transit Mk7 van. AUTODOC experts recommend:
    If you are using a jack, make sure the car is parked on a hard, flat surface.Make sure to additionally secure the car with jack stands.
  15. Step 16
    DIY replacement of Springs on FORD TRANSIT MK-7 Box 2.2 TDCi 2011 is not an issue anymore with our step-by-step tutorial
    Unscrew the wheel nuts.
    Replacement: coil springs – Ford Transit Mk7 van. Tip:
    To avoid injury, hold up the wheel when unscrewing the nuts.
  16. Step 17
    How to change Springs on Ford Transit Mk7 2006 - free PDF and video manuals
    Remove the wheel.
  17. Step 18
    How to replace FORD TRANSIT MK-7 Box 2.2 TDCi 2007 Springs - step-by-step manuals and video guides
    Clean the fastener that connects the anti-roll bar link to the suspension strut. Use a wire brush. Use WD-40 spray.
  18. Step 19
    Clean the fastener of the ABS sensor cable bracket. Use a wire brush. Use WD-40 spray.
    Step 20
    Ford Transit Mk7 2.4 TDCi RWD 2008 Springs replacement: free workshop manuals
    Clean the fastener connecting the suspension strut to the steering knuckle. Use a wire brush. Use WD-40 spray.
  19. Step 21
    Changing Springs on FORD TRANSIT MK-7 Box 2.4 TDCi RWD 2009 by yourself
    Unscrew the fastener of the ABS sensor cable bracket. Use an 18 mm socket. Use a ratchet wrench.
  20. Step 22
    How to remove FORD TRANSIT 2.2 TDCi 2010 Springs - online easy-to-follow instructions
    Detach the ABS sensor cable bracket from the suspension strut.
  21. Step 23
    How to replace Springs on FORD TRANSIT MK-7 Box 2011: download PDF manuals and video instructions
    Unscrew the fastener connecting the anti-roll bar link to the suspension strut. Use a 19 mm combination spanner. Use an H5 hex bit. Use a ratchet wrench.
  22. Step 24
    How hard is it to do yourself: Springs replacement on Ford Transit Mk7 2.2 TDCi 2012 - download illustrated guide
    Disconnect the anti-roll bar link from the suspension strut.
  23. Step 25
    Need to know how to renew Springs on FORD TRANSIT 2013? This free workshop manual will help you to do it yourself
    Unscrew the axle nut. Use a 36 mm socket. Use a ratchet wrench.
  24. Step 26
    Changing of Springs on Ford Transit Mk7 2014 won't be an issue if you follow this illustrated step-by-step guide
    Remove the axle washer. Use a telescoping magnetic pick-up tool.
  25. Step 27
    FORD TRANSIT 2.2 TDCi Springs replacement: online guides and video tutorials
    Support the suspension arm. Use a transmission jack or one more vehicle jack.
  26. Step 28
    Replacing Springs on Ford Transit Mk7 2007 2.2 TDCi by yourself
    Detach the CV axle from the steering knuckle. Use a pin punch. Use a hammer.
  27. Step 29
    TRANSIT MK-7 Box 2.2 TDCi 2008 Springs DIY replacement workshop manual
    Remove the support from under the suspension arm.
    AUTODOC recommendation:
    Lower the transmission or vehicle jack smoothly without jerking it to avoid damaging the vehicle assemblies and mechanisms.
  28. Step 30
    How to change Springs on FORD TRANSIT MK-7 Box 2009 - tips and tricks
    Clean the fastener that connects the ball joint to the suspension arm. Use a wire brush. Use WD-40 spray.
  29. Step 31
    Step-by-step recommendations for DIY replacement Ford Transit Mk7 2010 2.2 TDCi Springs
    Unscrew the fastener connecting the ball joint to the suspension arm. Use a 24 mm socket. Use a ratchet wrench.
  30. Step 32
    DIY replacement of Springs on FORD TRANSIT MK-7 Box 2.2 TDCi 2011 is not an issue anymore with our step-by-step tutorial
    Support the steering knuckle. Use a transmission jack or one more vehicle jack.
  31. Step 33
    How to change Springs on Ford Transit Mk7 2006 - free PDF and video manuals
    Disconnect the ball joint from the suspension arm. Use a ball joint separator. Use a mounting lever.
  32. Step 34
    Remove the support from under the steering knuckle.
    Step 35
    Release the ball joint from the suspension arm by pulling down the suspension arm with the mounting lever.
    Step 36
    After releasing the ball joint, move the steering knuckle a little to the side and carefully return the suspension arm to its original position.
    Step 37
    Support the steering knuckle again.
    Step 38
    Remove the CV axle from the steering knuckle.
    Step 39
    Tie the CV axle to the car body with a wire.
    Replacement: coil springs – Ford Transit Mk7 van. Tip from AUTODOC:
    Make sure that the CV axle is not hanging down.
    Step 40
    How to replace FORD TRANSIT MK-7 Box 2.2 TDCi 2007 Springs - step-by-step manuals and video guides
    Unscrew the lower fastener of the suspension strut. Use a 15 mm socket. Use a ratchet wrench.
  33. Step 41
    Ford Transit Mk7 2.4 TDCi RWD 2008 Springs replacement: free workshop manuals
    Remove the fastening bolt.
  34. Step 42
    Changing Springs on FORD TRANSIT MK-7 Box 2.4 TDCi RWD 2009 by yourself
    Disconnect the steering knuckle from the suspension strut. Use a rubber mallet. Use a transmission jack or one more vehicle jack.
    Warning!
    Make sure that the steering knuckle is not hanging loose on the brake hose or electric cable.
  35. Step 43
    How to remove FORD TRANSIT 2.2 TDCi 2010 Springs - online easy-to-follow instructions
    Unscrew the fasteners of the suspension strut mount.
    Replacement: coil springs – Ford Transit Mk7 van. Professionals recommend:
    To avoid injuries, hold the strut when undoing the fasteners.
  36. Step 44
    How to replace Springs on FORD TRANSIT MK-7 Box 2011: download PDF manuals and video instructions
    Remove the suspension strut assembly.
  37. Step 45
    How hard is it to do yourself: Springs replacement on Ford Transit Mk7 2.2 TDCi 2012 - download illustrated guide
    Clean the mounting seats of the suspension strut. Use a wire brush. Use an all-purpose cleaning spray.
  38. Step 46
    Need to know how to renew Springs on FORD TRANSIT 2013? This free workshop manual will help you to do it yourself
    Clean the fastener on the anti-roll bar link. Use a wire brush. Use an all-purpose cleaning spray.
  39. Step 47
    Changing of Springs on Ford Transit Mk7 2014 won't be an issue if you follow this illustrated step-by-step guide
    Clean the splines of the CV axle joint. Use a wire brush. Use an all-purpose cleaning spray.
  40. Step 48
    Depending on what part you are replacing, you may have to disassemble the suspension strut. But if you use all new components, then you will not need to disassemble the old strut. In this case, a stationary spring compressor will only be required to assemble a new strut if its parts were purchased separately.
    Step 49
    FORD TRANSIT 2.2 TDCi Springs replacement: online guides and video tutorials
    Set the suspension strut assembly on the stationary spring compressor.
    Replacement: coil springs – Ford Transit Mk7 van. Tip from AUTODOC experts:
    When using a stationary spring compressor, the spring coils must be securely clamped, compressing the spring from both ends.Make sure the spring is in the correct position.Make sure that the compressor jaws are tightly engaged onto the coils.
  41. Step 50
    Replacing Springs on Ford Transit Mk7 2007 2.2 TDCi by yourself
    Compress the spring.
  42. Step 51
    TRANSIT MK-7 Box 2.2 TDCi 2008 Springs DIY replacement workshop manual
    Clean the top part of the strut piston rod. Use a wire brush. Use WD-40 spray.
  43. Step 52
    How to change Springs on FORD TRANSIT MK-7 Box 2009 - tips and tricks
    Unscrew the strut piston rod nut. Use an 18 mm strut nut socket. Use an H6 hex extension bar. Use a ratchet wrench.
  44. Step 53
    Step-by-step recommendations for DIY replacement Ford Transit Mk7 2010 2.2 TDCi Springs
    Remove the top strut mount.
  45. Step 54
    DIY replacement of Springs on FORD TRANSIT MK-7 Box 2.2 TDCi 2011 is not an issue anymore with our step-by-step tutorial
    Release the spring.
  46. Step 55
    How to change Springs on Ford Transit Mk7 2006 - free PDF and video manuals
    Remove the mount bearing and the bump stop.
  47. Step 56
    How to replace FORD TRANSIT MK-7 Box 2.2 TDCi 2007 Springs - step-by-step manuals and video guides
    Remove the spring.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Searching for the right tyres?

Find out which tyre and wheel sizes are compatible with the FORD Transit Mk6 Van (V347, V348) model.

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
FORD TRANSIT MK-7 Box Springs replace by yourself - Scan QR-code and download AUTODOC CLUB app
Scan

To download the app:

  • - scan the QR code
  • - download from App Store
  • - download from Google Play
Autodoc CLUB App icon
DIY FORD TRANSIT MK-7 Box Springs replacement - online guide
Tips & tricks for your FORD TRANSIT MK-7 Box
View more
  • How to change Springs on FORD TRANSIT MK-7 Box 2.2 TDCi - replacement tricks
    What causes engine misfire? | AUTODOC
  • Changing Coil springs Ford Transit Mk7 2.2 TDCi - Replacement Tips
    5 car interior cleaning mistakes | AUTODOC tips
  • Maintenance Hacks - FORD TRANSIT MK-7 Box 2.4 TDCi RWD Spring replacement guide
    How to replace the suspension on a BMW E30 Turbo | SUPERCAR AUTODOC
  • Replace Suspension spring on Ford Transit Mk7 - free video tips
    Top 6 products for enhancing your car | AUTODOC tips