Disclaimer
How to change track rod end on VW Caddy III Van (2KA, 2KH, 2CA, 2CH) – replacement guide
downloads:
3
Views:
82
Important!
This replacement procedure can be used for:
VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 1.9 TDI 4motion, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 1.6 BiFuel, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 2.0 TDI 4motion, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 2.0 TDI, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 2.0 TDI 16V 4motion, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 2.0 TDI, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 2.0 TDI, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 1.4, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 1.6, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 2.0 SDI, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 1.9 TDI, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 2.0 EcoFuel, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 1.4, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 1.9 TDI, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 2.0 TDI, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 1.2 TSI, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 1.2 TSI, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 1.6 TDI, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 2.0 TDI 4motion, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 2.0 TDI 16V, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 1.6 TDI … View more
The steps may slightly vary depending on the car design.
VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 1.9 TDI 4motion, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 1.6 BiFuel, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 2.0 TDI 4motion, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 2.0 TDI, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 2.0 TDI 16V 4motion, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 2.0 TDI, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 2.0 TDI, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 1.4, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 1.6, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 2.0 SDI, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 1.9 TDI, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 2.0 EcoFuel, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 1.4, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 1.9 TDI, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 2.0 TDI, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 1.2 TSI, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 1.2 TSI, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 1.6 TDI, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 2.0 TDI 4motion, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 2.0 TDI 16V, VW Caddy III Van (2KA, 2KH, 2CA, 2CH) 1.6 TDI … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Track Rod End for Caddy III Van (2KA, 2KH, 2CA, 2CH) and other VW models
Alternative products

Wire brush
WD-40 spray
Brake cleaner
Copper grease
Combination spanner #22
Combination spanner #24
Drive socket # 18
Wheel impact socket #17
Ratchet wrench
Torque wrench
Vernier caliper
Tap wrench
Wheel chock
Replacement: track rod end – VW CADDY III Box (2KA, 2KH, 2CA, 2CH). Tip from AUTODOC experts:
- Replace tie rod ends in pairs.
- The replacement procedure is identical for the right and left tie rod ends.
- All work should be done with the engine stopped.
Replacement: track rod end – VW CADDY III Box (2KA, 2KH, 2CA, 2CH). Use the following procedure:
- Step 1
Secure the wheels with chocks. - Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #17. - Step 3Raise the front of the car and secure on supports.Step 4
Unscrew the wheel bolts.Replacement: track rod end – VW CADDY III Box (2KA, 2KH, 2CA, 2CH). AUTODOC recommends:To avoid injury, hold up the wheel when unscrewing the bolts. - Step 5
Remove the wheel. - Step 6
Clean the fastener connecting the tie rod end to the steering knuckle. Use a wire brush. Use WD-40 spray. - Step 7
Unscrew the end fastening nut to the steering knuckle. Use a drive socket #18. Use a tap wrench. - Step 8
When deinstalling, mark or measure the precise position of the ball joint on the track rod, or count the number of turns in order to prevent misalignment afterward. Use a vernier caliper. - Step 9
Loosen the lock nut securing the tie rod end to the tie rod. Use a combination spanner #24. - Step 10
Disconnect the tie rod end from the steering knuckle. - Step 11
Screw the end out of the tie rod. - Step 12
Clean the mounting seats of the tie rod end. Use a wire brush. Use WD-40 spray. - Step 13Screw on a new tie rod end.Replacement: track rod end – VW CADDY III Box (2KA, 2KH, 2CA, 2CH). Professionals recommend:While installing the steering rod end remember to make the same number of turns or to leave the same length of thread showing as per your measurements.Step 14
Connect the tie rod end to the steering knuckle.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the VW Caddy III Van (2KA, 2KH, 2CA, 2CH) model
Popular maintenance tutorials for VW Caddy Mk3
Complete guides for changing the Tie rod end on different VW CADDY models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your VW Caddy III Van (2KA, 2KH, 2CA, 2CH)
View more
5 mistakes made when washing the engine | AUTODOC tips
5 Ways You’re Scrubbing Your Car Wrong | AUTODOC Tips
How to Get the Best Deals on Car Parts | Save Money with AUTODOC
Deep interior cleaning | Car transformation by detailing
Most commonly replaced car parts on VW CADDY
Time to replace parts? Get even better deals in our Shop app.

SCAN ME





























