
Disclaimer
How to change track rod end on VW Caddy II Van (9K9A) – replacement guide
downloads:
0
Views:
6
Important!
This replacement procedure can be used for:
VW Caddy II Van (9K9A) 60 1.4, VW Caddy II Van (9K9A) 1.9 SDI, VW Caddy II Van (9K9A) 75 1.6, VW Caddy II Van (9K9A) 1.9 TDI, VW Caddy II Van (9K9A) 1.7 SDI, VW Caddy II Van (9K9A) 1.9 D, VW Caddy II Van (9K9A) 1.4, VW Caddy II Van (9K9A) 75 1.6, VW Caddy II Van (9K9A) 1.8 … View more
The steps may slightly vary depending on the car design.
VW Caddy II Van (9K9A) 60 1.4, VW Caddy II Van (9K9A) 1.9 SDI, VW Caddy II Van (9K9A) 75 1.6, VW Caddy II Van (9K9A) 1.9 TDI, VW Caddy II Van (9K9A) 1.7 SDI, VW Caddy II Van (9K9A) 1.9 D, VW Caddy II Van (9K9A) 1.4, VW Caddy II Van (9K9A) 75 1.6, VW Caddy II Van (9K9A) 1.8 … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Track Rod End for Caddy II Van (9K9A) and other VW models
Track rod end
Alternative products

Wire brush
WD-40 spray
Brake cleaner
Copper grease
Combination spanner #22
Drive socket # 19
Wheel impact socket #17
Ratchet wrench
Torque wrench
Vernier caliper
Ball joint puller
Wheel chock
Replacement: track rod end – VW CADDY II Box (9K9A). AUTODOC experts recommend:
- Replace tie rod ends in pairs.
- The replacement procedure is identical for the right and left tie rod ends.
- All work should be done with the engine stopped.
Replacement: track rod end – VW CADDY II Box (9K9A). Recommended sequence of steps:
- Step 1Secure the wheels with chocks.
- Step 2Loosen the wheel mounting bolts. Use wheel impact socket #17.
- Step 3Raise the front of the car and secure on supports.Step 4Unscrew the wheel bolts.AUTODOC recommends:Important! Hold the wheel while unscrewing the fastening bolts. VW CADDY II Box (9K9A)
- Step 5Remove the wheel.
- Step 6When deinstalling, mark or measure the precise position of the ball joint on the track rod, or count the number of turns in order to prevent misalignment afterward. Use a vernier caliper.
- Step 7Clean the lock nut that connects the tie rod to the tie rod end. Use a wire brush. Use WD-40 spray.Step 8Loosen the lock nut securing the tie rod end to the tie rod. Use a combination spanner #22.
- Step 9Clean the fastener connecting the tie rod end to the steering knuckle. Use a wire brush. Use WD-40 spray.Step 10Unscrew the end fastening nut to the steering knuckle. Use a drive socket #19. Use a ratchet wrench.
- Step 11Disconnect the tie rod end from the steering knuckle. Use a ball joint puller.
- Step 12Screw the end out of the tie rod.
- Step 13Clean the mounting seats of the tie rod end. Use a wire brush. Use WD-40 spray.Step 14Screw on a new tie rod end.Replacement: track rod end – VW CADDY II Box (9K9A). Tip from AUTODOC experts:While installing the steering rod end remember to make the same number of turns or to leave the same length of thread showing as per your measurements.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the VW Caddy II Van (9K9A) model
Popular maintenance tutorials for VW Caddy 2 Van
Complete guides for changing the Tie rod end on different VW CADDY models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your VW Caddy II Van (9K9A)
View more
- Easy Steps to Fix Minor Scratches on Your Vehicle | AUTODOC tips
- Top 5 possible reasons your car is shaking or vibrating
- How to Install a New Windscreen Yourself | AUTODOC Expert Tips
- DIY car soundproofing | AUTODOC tips
Most commonly replaced car parts on VW CADDY
Time to replace parts? Get even better deals in our Shop app.

SCAN ME