Disclaimer
How to change track rod end on SEAT Tarraco (KN2_) – replacement guide
downloads:
4
Views:
29
Important!
This replacement procedure can be used for:
SEAT Tarraco (KN2_) 1.5 TSi ACT, SEAT Tarraco (KN2_) 2.0 TDi, SEAT Tarraco (KN2_) 2.0 TDi 4Drive, SEAT Tarraco (KN2_) 2.0 TDi 4Drive, SEAT Tarraco (KN2_) 2.0 TSi 4Drive, SEAT Tarraco (KN2_) 2.0 TDI 4Drive, SEAT Tarraco (KN2_) 2.0 TFSI 4Drive, SEAT Tarraco (KN2_) 1.4 e-HYBRID … View more
The steps may slightly vary depending on the car design.
SEAT Tarraco (KN2_) 1.5 TSi ACT, SEAT Tarraco (KN2_) 2.0 TDi, SEAT Tarraco (KN2_) 2.0 TDi 4Drive, SEAT Tarraco (KN2_) 2.0 TDi 4Drive, SEAT Tarraco (KN2_) 2.0 TSi 4Drive, SEAT Tarraco (KN2_) 2.0 TDI 4Drive, SEAT Tarraco (KN2_) 2.0 TFSI 4Drive, SEAT Tarraco (KN2_) 1.4 e-HYBRID … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Track Rod End for Tarraco (KN2_) and other SEAT models
Alternative products

Wire brush
WD-40 spray
Brake cleaner
Copper grease
Combination spanner #22
Combination spanner #24
Drive socket # 18
Wheel impact socket #17
Ratchet wrench
Torque wrench
Tap wrench
Vernier caliper
Ball joint puller
Wheel chock
Replacement: track rod end – SEAT Tarraco (KN2_). Tip from AUTODOC experts:
- Replace tie rod ends in pairs.
- The replacement procedure is identical for the right and left tie rod ends.
- All work should be done with the engine stopped.
Replacement: track rod end – SEAT Tarraco (KN2_). Recommended sequence of steps:
- Step 1Secure the wheels with chocks.Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #17. - Step 3Raise the front of the car and secure on supports.Step 4
Unscrew the wheel bolts.Replacement: track rod end – SEAT Tarraco (KN2_). Tip:To avoid injury, hold up the wheel when unscrewing the bolts. - Step 5
Remove the wheel. - Step 6
Clean the fastener connecting the tie rod end to the steering knuckle. Use a wire brush. Use WD-40 spray. - Step 7
When deinstalling, mark or measure the precise position of the ball joint on the track rod, or count the number of turns in order to prevent misalignment afterward. Use a vernier caliper. - Step 8
Loosen the lock nut securing the tie rod end to the tie rod. Use a combination spanner #24. - Step 9
Unscrew the end fastening nut to the steering knuckle. Use a drive socket #18. Use a tap wrench. - Step 10
Disconnect the tie rod end from the steering knuckle. Use a ball joint puller. - Step 11
Screw the end out of the tie rod. - Step 12
Clean the mounting seats of the tie rod end. Use a wire brush. Use WD-40 spray. - Step 13
Screw on a new tie rod end.AUTODOC recommends:While installing the steering rod end remember to make the same number of turns or to leave the same length of thread showing as per your measurements. - Step 14
Connect the tie rod end to the steering knuckle. - Step 15
Screw on the fastening nut that connects the tie rod end to the steering knuckle. Use a drive socket #18. Use a ratchet wrench.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the SEAT Tarraco (KN2_) model
Popular maintenance tutorials for SEAT Tarraco (KN2_)
Complete guides for changing the Tie rod end on different SEAT TARRACO models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your SEAT Tarraco (KN2_)
View more
5 mistakes when replacing consumables
How to choose the right engine oil for your car | AUTODOC
Top 5 Mistakes to Avoid for Safe Engine Bay Repairs | AUTODOC Tips
How to Fix a Squealing Belt: Causes & Solutions | AUTODOC Expert Tips
Most commonly replaced car parts on SEAT TARRACO
Time to replace parts? Get even better deals in our Shop app.

SCAN ME






























