Disclaimer
How to change track rod end on RENAULT Clio III Van (SB_, SR_) – replacement guide
downloads:
0
Views:
11
Important!
This replacement procedure can be used for:
RENAULT Clio III Van (SB_, SR_) 1.5 dCi … View more
The steps may slightly vary depending on the car design.
RENAULT Clio III Van (SB_, SR_) 1.5 dCi … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Track Rod End for Clio III Van (SB_, SR_) and other RENAULT models
Alternative products

Wire brush
WD-40 spray
Brake cleaner
Copper grease
Combination spanner #13
Combination spanner #21
Combination spanner #22
Drive socket # 13
Drive socket # 17
Drive socket # 18
Wheel impact socket #17
Ratchet wrench
Torque wrench
Vernier caliper
Ball joint puller
Wheel chock
Replacement: track rod end – RENAULT CLIO III Box (SB_, SR_). AUTODOC experts recommend:
- Replace tie rod ends in pairs.
- The replacement procedure is identical for the right and left tie rod ends.
- During the installation process, use only new bolts and nuts.
- Please note: all work on the car – RENAULT CLIO III Box (SB_, SR_) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1
Secure the wheels with chocks. - Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #17. - Step 3Raise the front of the car and secure on supports.Step 4
Unscrew the wheel bolts.AUTODOC recommends:Important! Hold the wheel while unscrewing the fastening bolts. RENAULT CLIO III Box (SB_, SR_) - Step 5
Remove the wheel. - Step 6
Clean the fastener connecting the tie rod end to the steering knuckle. Use a wire brush. Use WD-40 spray. - Step 7
When deinstalling, mark or measure the precise position of the ball joint on the track rod, or count the number of turns in order to prevent misalignment afterward. Use a vernier caliper. - Step 8
Loosen the lock nut securing the tie rod end to the tie rod. Use a combination spanner #21. Use a combination spanner #22. - Step 9
Unscrew the end fastening nut to the steering knuckle. Use a drive socket #17. Use a ratchet wrench. - Step 10
Loosen the fastener connecting the tie rod end to the tie rod. Use a drive socket #13. Use a ratchet wrench. - Step 11
Disconnect the tie rod end from the steering knuckle. Use a ball joint puller. - Step 12
Screw the end out of the tie rod. Use a combination spanner #13. Use a combination spanner #21. - Step 13
Clean the mounting seats of the tie rod end. Use a wire brush. Use WD-40 spray. - Step 14
Treat the threaded part of the tie rod. Use copper grease. - Step 15
Screw on a new tie rod end.Replacement: track rod end – RENAULT CLIO III Box (SB_, SR_). AUTODOC recommends:While installing the steering rod end remember to make the same number of turns or to leave the same length of thread showing as per your measurements. - Step 16
Clean the mounting seats of the tie rod end. Use a wire brush. Use WD-40 spray. - Step 17
Connect the tie rod end to the steering knuckle.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the RENAULT Clio III Van (SB_, SR_) model
Popular maintenance tutorials for Renault Clio 3 Van
Complete guides for changing the Tie rod end on different RENAULT CLIO models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your RENAULT Clio III Van (SB_, SR_)
View more
Prevent Engine Damage: How to Identify Rocker Cover Gasket Issues and Proper Replacement | AUTODOC
DIY engine block coffee table
DIY vehicle AC compressor restoration
Three ways to change oil without a lift
Most commonly replaced car parts on RENAULT CLIO
Time to replace parts? Get even better deals in our Shop app.

SCAN ME































