Important!
This replacement procedure can be used for:
RENAULT Clio III Van (SB_, SR_) 1.5 dCi, RENAULT Clio III Van (SB_, SR_) 1.2 (SR0J), RENAULT Clio III Van (SB_, SR_) 1.2 (SR0P), RENAULT Clio III Van (SB_, SR_) 1.5 dCi (SR1H), RENAULT Clio III Van (SB_, SR_) 1.5 dCi View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

Tools
Replacement: wheel bearing – RENAULT CLIO III Box (SB_, SR_). List of the tools you'll need:
Wire brush
WD-40 spray
Brake cleaner
Copper grease
Torque wrench
Combination spanner #16
Combination spanner #18
Torx bit T30
Drive socket # 10
Drive socket # 16
Drive socket # 17
Drive socket # 18
Drive socket # 30
Wheel impact socket #17
Bush and bearing driver set
Ratchet wrench
Tap wrench
Hammer
Pin punch
Flat chisel
Flat Screwdriver
Circlip pliers
Clip removal tool
3-Arm Gear Puller
Ball joint puller
Bearing separator
Vice
Crow bar
Wheel chock
Replacement: wheel bearing – RENAULT CLIO III Box (SB_, SR_). Tip from AUTODOC experts:
  • Do not re-use the bearing assembly of your RENAULT CLIO III Box (SB_, SR_) car.
  • The wheel hub bearing replacement procedure is identical for both wheels on the same axle.
  • Please note: all work on the car – RENAULT CLIO III Box (SB_, SR_) – should be done with the engine switched off.
Carry out replacement in the following order:
  1. Step 1
    Secure the wheels with chocks.
    Step 2
    How to change Wheel Bearing on Renault Clio 3 Van 2005 - free PDF and video manuals
    Loosen the wheel mounting bolts. Use wheel impact socket #17.
  2. Step 3
    How to replace RENAULT Clio III Van (SB_, SR_) 1.5 dCi 2006 Wheel Bearing - step-by-step manuals and video guides
    Clean the fastener of the driveshaft. Use WD-40 spray.
  3. Step 4
    Renault Clio 3 Van 1.2 (SR0J) 2007 Wheel Bearing replacement: free workshop manuals
    Unscrew the fastener connecting the drive shaft to the wheel hub. Use a drive socket #30. Use a tap wrench.
  4. Step 5
    Raise the front of the car and secure on supports.
    Step 6
    Changing Wheel Bearing on RENAULT Clio III Van (SB_, SR_) 1.5 dCi (SR1H) 2008 by yourself
    Unscrew the wheel bolts.
    AUTODOC recommends:
    Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. RENAULT CLIO III Box (SB_, SR_)
  5. Step 7
    How to remove RENAULT CLIO 1.2 Hi-Flex (SR1U) 2009 Wheel Bearing - online easy-to-follow instructions
    Remove the wheel.
  6. Step 8
    How to replace Wheel Bearing on RENAULT Clio III Van (SB_, SR_) 2010: download PDF manuals and video instructions
    Disconnect the ABS sensor wiring. Use a crowbar.
  7. Step 9
    How hard is it to do yourself: Wheel Bearing replacement on Renault Clio 3 Van 1.2 (SR0J) 2011 - download illustrated guide
    Unscrew the brake hose fastening bracket from the shock strut. Use a drive socket #10. Use a ratchet wrench.
  8. Step 10
    Need to know how to renew Wheel Bearing on RENAULT CLIO 2012? This free workshop manual will help you to do it yourself
    Disconnect the brake hose mounting bracket.
  9. Step 11
    Changing of Wheel Bearing on Renault Clio 3 Van 2013 won't be an issue if you follow this illustrated step-by-step guide
    Spread the brake pads. Use a crowbar.
  10. Step 12
    RENAULT CLIO 1.5 dCi (SR1H) Wheel Bearing replacement: online guides and video tutorials
    Clean the brake caliper bracket fasteners. Use a wire brush. Use WD-40 spray.
  11. Step 13
    Replacing Wheel Bearing on Renault Clio 3 Van 2015 1.5 dCi by yourself
    Unscrew the caliper bracket fastening. Use a drive socket #18. Use a tap wrench.
  12. Step 14
    Clio III Van (SB_, SR_) 1.2 Hi-Flex (SR1U) 2016 Wheel Bearing DIY replacement workshop manual
    Remove the brake caliper together with its bracket.
    Replacement: wheel bearing – RENAULT CLIO III Box (SB_, SR_). AUTODOC experts recommend:
    Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur.
  13. Step 15
    How to change Wheel Bearing on RENAULT Clio III Van (SB_, SR_) 2017 - tips and tricks
    Clean the brake disc fasteners. Use a wire brush. Use WD-40 spray.
  14. Step 16
    Step-by-step recommendations for DIY replacement Renault Clio 3 Van 2018 1.2 Hi-Flex (SR1U) Wheel Bearing
    Unscrew the brake disc fastening. Use Torx T30. Use a ratchet wrench.
  15. Step 17
    DIY replacement of Wheel Bearing on RENAULT Clio III Van (SB_, SR_) 1.2 (SR0P) 2019 is not an issue anymore with our step-by-step tutorial
    Remove the brake disc.
  16. Step 18
    How to change Wheel Bearing on Renault Clio 3 Van 2005 - free PDF and video manuals
    Remove the wheel arch cover. Use a clip removal tool.
  17. Step 19
    How to replace RENAULT Clio III Van (SB_, SR_) 1.5 dCi 2006 Wheel Bearing - step-by-step manuals and video guides
    Disconnect the ABS sensor wiring. Use a clip removal tool.
  18. Step 20
    Renault Clio 3 Van 1.2 (SR0J) 2007 Wheel Bearing replacement: free workshop manuals
    Detach the ABS sensor connector.
  19. Step 21
    Changing Wheel Bearing on RENAULT Clio III Van (SB_, SR_) 1.5 dCi (SR1H) 2008 by yourself
    Clean all joints of the arm. Use a wire brush. Use WD-40 spray.
  20. Step 22
    How to remove RENAULT CLIO 1.2 Hi-Flex (SR1U) 2009 Wheel Bearing - online easy-to-follow instructions
    Unscrew the ball joint fastening to the steering knuckle. Use a combination spanner #16. Use a drive socket #16. Use a tap wrench.
  21. Step 23
    How to replace Wheel Bearing on RENAULT Clio III Van (SB_, SR_) 2010: download PDF manuals and video instructions
    Remove the fastening bolt.
  22. Step 24
    How hard is it to do yourself: Wheel Bearing replacement on Renault Clio 3 Van 1.2 (SR0J) 2011 - download illustrated guide
    Clean the fastener connecting the tie rod end to the steering knuckle. Use a wire brush. Use WD-40 spray.
  23. Step 25
    Need to know how to renew Wheel Bearing on RENAULT CLIO 2012? This free workshop manual will help you to do it yourself
    Unscrew the end fastening nut to the steering knuckle. Use a drive socket #17. Use a ratchet wrench.
  24. Step 26
    Changing of Wheel Bearing on Renault Clio 3 Van 2013 won't be an issue if you follow this illustrated step-by-step guide
    Disconnect the tie rod end from the steering knuckle. Use a ball joint puller.
  25. Step 27
    RENAULT CLIO 1.5 dCi (SR1H) Wheel Bearing replacement: online guides and video tutorials
    Unscrew the fastener connecting the drive shaft to the wheel hub. Use a drive socket #30. Use a ratchet wrench.
  26. Step 28
    Replacing Wheel Bearing on Renault Clio 3 Van 2015 1.5 dCi by yourself
    Unscrew the lower fastener connecting the shock strut to the steering knuckle. Use a combination spanner #18. Use a drive socket #18. Use a ratchet wrench.
  27. Step 29
    Clio III Van (SB_, SR_) 1.2 Hi-Flex (SR1U) 2016 Wheel Bearing DIY replacement workshop manual
    Release the fastener that connects the control arm ball joint to the steering knuckle. Use a flat metal-working chisel. Use a hammer.
  28. Step 30
    How to change Wheel Bearing on RENAULT Clio III Van (SB_, SR_) 2017 - tips and tricks
    Disconnect the ball joint from the steering knuckle. Use a crowbar.
  29. Step 31
    Step-by-step recommendations for DIY replacement Renault Clio 3 Van 2018 1.2 Hi-Flex (SR1U) Wheel Bearing
    Detach the driveshaft from the steering knuckle.
    Replacement: wheel bearing – RENAULT CLIO III Box (SB_, SR_). AUTODOC recommends:
    Make sure that the drive shaft is not unloaded (when the car is jacked).
  30. Step 32
    DIY replacement of Wheel Bearing on RENAULT Clio III Van (SB_, SR_) 1.2 (SR0P) 2019 is not an issue anymore with our step-by-step tutorial
    Remove the fastening bolts.
  31. Step 33
    How to change Wheel Bearing on Renault Clio 3 Van 2005 - free PDF and video manuals
    Disconnect the steering knuckle from the shock absorber strut.
  32. Step 34
    Remove the steering knuckle together with the hub.
    Step 35
    How to replace RENAULT Clio III Van (SB_, SR_) 1.5 dCi 2006 Wheel Bearing - step-by-step manuals and video guides
    Grip the wheel hub together with the bearing in a vice.
  33. Step 36
    Renault Clio 3 Van 1.2 (SR0J) 2007 Wheel Bearing replacement: free workshop manuals
    Clean the ABS sensor fastener. Use a wire brush. Use WD-40 spray.
  34. Step 37
    Changing Wheel Bearing on RENAULT Clio III Van (SB_, SR_) 1.5 dCi (SR1H) 2008 by yourself
    Disconnect the ABS sensor. Use a flat screwdriver.
  35. Step 38
    How to remove RENAULT CLIO 1.2 Hi-Flex (SR1U) 2009 Wheel Bearing - online easy-to-follow instructions
    Remove the wheel hub from the steering knuckle. Use a pin punch. Use a hammer.
  36. Step 39
    How to replace Wheel Bearing on RENAULT Clio III Van (SB_, SR_) 2010: download PDF manuals and video instructions
    Pull the bearing inner race out of the wheel hub. Use 3-Arm Gear Puller. Use a bearing separator.
  37. Step 40
    How hard is it to do yourself: Wheel Bearing replacement on Renault Clio 3 Van 1.2 (SR0J) 2011 - download illustrated guide
    Clean the wheel hub bearing retaining ring. Use a wire brush. Use WD-40 spray.
  38. Step 41
    Need to know how to renew Wheel Bearing on RENAULT CLIO 2012? This free workshop manual will help you to do it yourself
    Remove the wheel hub bearing retaining ring. Use circlip pliers. Use a flat screwdriver.
  39. Step 42
    Changing of Wheel Bearing on Renault Clio 3 Van 2013 won't be an issue if you follow this illustrated step-by-step guide
    Clean the hub bearing mounting seat. Use a wire brush. Use WD-40 spray.
  40. Step 43
    Release the vice and take out the wheel hub together with the bearing.
    Step 44
    RENAULT CLIO 1.5 dCi (SR1H) Wheel Bearing replacement: online guides and video tutorials
    Press out the wheel hub bearing. Use a bush and bearing driver set.
  41. Step 45
    Replacing Wheel Bearing on Renault Clio 3 Van 2015 1.5 dCi by yourself
    Clean the hub bearing mounting seat. Use a wire brush. Use WD-40 spray.
  42. Step 46
    Clio III Van (SB_, SR_) 1.2 Hi-Flex (SR1U) 2016 Wheel Bearing DIY replacement workshop manual
    Press the new bearing in the steering knuckle. Use a bush and bearing driver set.
    Replacement: wheel bearing – RENAULT CLIO III Box (SB_, SR_). Tip from AUTODOC:
    Check to make sure the wheel hub bearing is positioned correctly. Avoid its misalignment. Stop pressing on the surface of the bearing immediately after it has been fitted into its mounting seat.
  43. Step 47
    How to change Wheel Bearing on RENAULT Clio III Van (SB_, SR_) 2017 - tips and tricks
    Install the wheel hub bearing retaining ring. Use circlip pliers.
  44. Step 48
    Step-by-step recommendations for DIY replacement Renault Clio 3 Van 2018 1.2 Hi-Flex (SR1U) Wheel Bearing
    Treat the fasteners of the wheel hub bearing. Use WD-40 spray.
  45. Step 49
    DIY replacement of Wheel Bearing on RENAULT Clio III Van (SB_, SR_) 1.2 (SR0P) 2019 is not an issue anymore with our step-by-step tutorial
    Install the wheel hub on the steering knuckle. Use a bush and bearing driver set.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Searching for the right tyres?

Find out which tyre and wheel sizes are compatible with the RENAULT Clio III Van (SB_, SR_) model.

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
RENAULT Clio III Van (SB_, SR_) Wheel Bearing replace by yourself - Scan QR-code and download AUTODOC CLUB app
Scan

To download the app:

  • - scan the QR code
  • - download from App Store
  • - download from Google Play
Autodoc CLUB App icon
DIY RENAULT Clio III Van (SB_, SR_) Wheel Bearing replacement - online guide
Tips & tricks for your RENAULT Clio III Van (SB_, SR_)
View more
  • How to change Wheel bearings on RENAULT Clio III Van (SB_, SR_) 1.2 (SR0P) - replacement tricks
    Coolant comparison test | AUTODOC
  • Changing Hub bearing Renault Clio 3 Van 1.5 dCi - Replacement Tips
    Unveiling the secrets: Detecting vacuum leaks with a Smoke Machine | AUTODOC
  • Maintenance Hacks - RENAULT Clio III Van (SB_, SR_) 1.2 (SR0J) Wheel bearing kit replacement guide
    Preventing Engine Failure: Head Gasket Inspection Tutorial | AUTODOC
  • Replace Wheel hub bearing on Renault Clio 3 Van - free video tips
    #DIY Guide: How to Fix a Cracked Windscreen Without a Garage Visit