Disclaimer
How to change track rod end on HONDA Jazz Hatchback (GE, GG, GP, ZA) – replacement guide
downloads:
10
Views:
60
Important!
This replacement procedure can be used for:
HONDA Jazz III Hatchback (GE_, GG_, GP_, ZA_) 1.2 (GG1), HONDA Jazz III Hatchback (GE_, GG_, GP_, ZA_) 1.3 i (GE6, GG3, GG6), HONDA Jazz III Hatchback (GE_, GG_, GP_, ZA_) 1.4, HONDA Jazz III Hatchback (GE_, GG_, GP_, ZA_) 1.3 HYBRID (GP1) … View more
The steps may slightly vary depending on the car design.
HONDA Jazz III Hatchback (GE_, GG_, GP_, ZA_) 1.2 (GG1), HONDA Jazz III Hatchback (GE_, GG_, GP_, ZA_) 1.3 i (GE6, GG3, GG6), HONDA Jazz III Hatchback (GE_, GG_, GP_, ZA_) 1.4, HONDA Jazz III Hatchback (GE_, GG_, GP_, ZA_) 1.3 HYBRID (GP1) … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Track Rod End for Jazz III Hatchback (GE_, GG_, GP_, ZA_) and other HONDA models
Alternative products

Wire brush
WD-40 spray
Brake cleaner
Copper grease
Combination spanner #19
Drive socket # 17
Wheel impact socket #19
Ratchet wrench
Torque wrench
Round-nose pliers
Vernier caliper
Tap wrench
Ball joint puller
Crow bar
Wheel chock
Replacement: track rod end – HONDA JAZZ III (GE). AUTODOC recommends:
- Replace tie rod ends in pairs.
- The replacement procedure is identical for the right and left tie rod ends.
- All work should be done with the engine stopped.
Replacement: track rod end – HONDA JAZZ III (GE). Recommended sequence of steps:
- Step 1
Secure the wheels with chocks. - Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #19. - Step 3Raise the front of the car and secure on supports.Step 4
Unscrew the wheel bolts.Replacement: track rod end – HONDA JAZZ III (GE). Tip:To avoid injury, hold up the wheel when unscrewing the bolts. - Step 5
Remove the wheel. - Step 6
Clean the fastener connecting the tie rod end to the steering knuckle. Use a wire brush. Use WD-40 spray. - Step 7
Remove the cotter pin fixing the tie rod end fastening. Use a crowbar. Use round-nose pliers. - Step 8
Unscrew the end fastening nut to the steering knuckle. Use a drive socket #17. Use a tap wrench. - Step 9
Disconnect the tie rod end from the steering knuckle. Use a ball joint puller. - Step 10
When deinstalling, mark or measure the precise position of the ball joint on the track rod, or count the number of turns in order to prevent misalignment afterward. Use a vernier caliper. - Step 11
Loosen the lock nut securing the tie rod end to the tie rod. Use a combination spanner #19. - Step 12
Screw the end out of the tie rod. - Step 13
Clean the mounting seats of the tie rod end. Use a wire brush. Use WD-40 spray. - Step 14
Screw on a new tie rod end.Replacement: track rod end – HONDA JAZZ III (GE). AUTODOC experts recommend:While installing the steering rod end remember to make the same number of turns or to leave the same length of thread showing as per your measurements. - Step 15
Connect the tie rod end to the steering knuckle.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the HONDA Jazz Hatchback (GE, GG, GP, ZA) model
Popular maintenance tutorials for Honda Jazz GE
Complete guides for changing the Tie rod end on different HONDA JAZZ models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your HONDA Jazz III Hatchback (GE_, GG_, GP_, ZA_)
View more
Easy Steps to Fix Minor Scratches on Your Vehicle | AUTODOC tips
5 Essential Tips for beginner drivers: Avoid Common Mistakes
Regain Your Confidence on the Road: Easy Headlight Restoration Tips
How to make an injector test bench yourself
Most commonly replaced car parts on HONDA JAZZ
Time to replace parts? Get even better deals in our Shop app.

SCAN ME
























