Important!
This replacement procedure can be used for:
CITROËN C2 Enterprise (JG_) 1.1, CITROËN C2 Enterprise (JG_) 1.4 HDi, CITROËN C2 Enterprise (JG_) 1.4 HDi View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Track Rod End for C2 Enterprise (JG_) and other CITROËN models
Alternative products
How to change Track rod end on Citroen C2 Enterprise 1.4 HDi – step-by-step instructions for straightforward car repair Track rod end
Tools
Replacement: track rod end – CITROËN C2 ENTERPRISE. List of the tools you'll need:
Wire brush
WD-40 spray
Brake cleaner
Copper grease
Combination spanner #22
Drive socket # 17
Wheel impact socket #17
Ratchet wrench
Torque wrench
Tap wrench
Vernier caliper
Wheel chock
Replacement: track rod end – CITROËN C2 ENTERPRISE. Tip:
  • Replace tie rod ends in pairs.
  • The replacement procedure is identical for the right and left tie rod ends.
  • During the installation process, use only new bolts and nuts.
  • All work should be done with the engine stopped.
Replacement: track rod end – CITROËN C2 ENTERPRISE. Recommended sequence of steps:
  1. Step 1
    How to change Track Rod End on Citroen C2 Enterprise 2009 - free PDF and video manuals
    Secure the wheels with chocks.
  2. Step 2
    How to replace CITROËN C2 Enterprise (JG_) 1.4 HDi 2009 Track Rod End - step-by-step manuals and video guides
    Loosen the wheel mounting bolts. Use wheel impact socket #17.
  3. Step 3
    Raise the front of the car and secure on supports.
    Step 4
    Citroen C2 Enterprise 1.1 2009 Track Rod End replacement: free workshop manuals
    Unscrew the wheel bolts.
    Replacement: track rod end – CITROËN C2 ENTERPRISE. AUTODOC recommends:
    To avoid injury, hold up the wheel when unscrewing the bolts.
  4. Step 5
    Changing Track Rod End on CITROËN C2 Enterprise (JG_) 1.1 2009 by yourself
    Remove the wheel.
  5. Step 6
    How to remove CITROËN C2 1.4 HDi 2009 Track Rod End - online easy-to-follow instructions
    Clean the fastener connecting the tie rod end to the steering knuckle. Use a wire brush. Use WD-40 spray.
  6. Step 7
    How to replace Track Rod End on CITROËN C2 Enterprise (JG_) 2009: download PDF manuals and video instructions
    When deinstalling, mark or measure the precise position of the ball joint on the track rod, or count the number of turns in order to prevent misalignment afterward. Use a vernier caliper.
  7. Step 8
    How hard is it to do yourself: Track Rod End replacement on Citroen C2 Enterprise 1.4 HDi 2009 - download illustrated guide
    Unscrew the end fastening nut to the steering knuckle. Use a drive socket #17. Use a tap wrench.
  8. Step 9
    Need to know how to renew Track Rod End on CITROËN C2 2009? This free workshop manual will help you to do it yourself
    Loosen the lock nut securing the tie rod end to the tie rod. Use a combination spanner #22.
  9. Step 10
    Changing of Track Rod End on Citroen C2 Enterprise 2009 won't be an issue if you follow this illustrated step-by-step guide
    Disconnect the tie rod end from the steering knuckle.
  10. Step 11
    CITROËN C2 1.4 HDi Track Rod End replacement: online guides and video tutorials
    Screw the end out of the tie rod.
  11. Step 12
    Replacing Track Rod End on Citroen C2 Enterprise 2009 1.4 HDi by yourself
    Clean the mounting seats of the tie rod end. Use a wire brush. Use WD-40 spray.
  12. Step 13
    C2 Enterprise (JG_) 1.4 HDi 2009 Track Rod End DIY replacement workshop manual
    Screw on a new tie rod end.
    Replacement: track rod end – CITROËN C2 ENTERPRISE. AUTODOC experts recommend:
    While installing the steering rod end remember to make the same number of turns or to leave the same length of thread showing as per your measurements.
  13. Step 14
    How to change Track Rod End on CITROËN C2 Enterprise (JG_) 2009 - tips and tricks
    Treat the threaded part of the tie rod. Use copper grease.
  14. Step 15
    Step-by-step recommendations for DIY replacement Citroen C2 Enterprise 2009 1.4 HDi Track Rod End
    Connect the tie rod end to the steering knuckle.
  15. Step 16
    DIY replacement of Track Rod End on CITROËN C2 Enterprise (JG_) 1.4 HDi 2009 is not an issue anymore with our step-by-step tutorial
    Screw on the fastening nut that connects the tie rod end to the steering knuckle. Use a drive socket #17. Use a ratchet wrench.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?

Find out which tyre and wheel sizes are compatible with the CITROËN C2 Enterprise (JG) model

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

DIY CITROËN C2 Enterprise (JG_) Track Rod End replacement - online guide
Tips & tricks for your CITROËN C2 Enterprise (JG_)
View more
  • How to change Tie rod end on CITROËN C2 Enterprise (JG_) 1.4 HDi - replacement tricks
    Coolant comparison test | AUTODOC
  • Changing Outer tie rod Citroen C2 Enterprise 1.4 HDi - Replacement Tips
    Regain Your Confidence on the Road: Easy Headlight Restoration Tips
  • Maintenance Hacks - CITROËN C2 Enterprise (JG_) 1.1 Track rod end ball joint replacement guide
    Top 5 possible reasons your car is shaking or vibrating
  • Replace Outer tie rod end on Citroen C2 Enterprise - free video tips
    Why Checking Your Oil is Crucial for Engine Performance
Autodoc CLUB App icon
Time to replace parts? Get even better deals in our Shop app.
CITROËN C2 Enterprise (JG_) Track Rod End replace by yourself - Scan QR-code and download AUTODOC CLUB app
SCAN ME