
Disclaimer
How to change spark plugs on VAUXHALL Adam (M13) – replacement guide
downloads:
9
Views:
232

Recommended replacement interval for the part category Spark plug : 4 year / 60000 km
Important!
This replacement procedure can be used for:
VAUXHALL Adam (M13) 1.4, VAUXHALL Adam (M13) 1.4, VAUXHALL Adam (M13) 1.2 … View more
The steps may slightly vary depending on the car design.
VAUXHALL Adam (M13) 1.4, VAUXHALL Adam (M13) 1.4, VAUXHALL Adam (M13) 1.2 … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Spark Plug for Adam (M13) and other VAUXHALL models
Spark plug
Alternative products

Electronic spray
High-temperature anti-seize lubricant
Spark plug socket # 16
Torx bit T40
Ratchet wrench
Torque wrench
Flat Screwdriver
Telescoping magnet
Crow bar
Fender cover
Replacement: spark plugs – VAUXHALL ADAM. Tip from AUTODOC:
- The replacement procedure is the same for all spark plugs.
- All work should be done with the engine stopped.
Replacement: spark plugs – VAUXHALL ADAM. Use the following procedure:
- Step 1Open the hood.Step 2Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.Step 3Remove the engine cover.Replacement: spark plugs – VAUXHALL ADAM. Tip:Raise the engine cover, holding it on two sides simultaneously.
- Step 4Detach the connector from the ignition coil.
- Step 5Unscrew the ignition coil bracket. Use Torx T40. Use a ratchet wrench.
- Step 6Pry up the ignition coil. Use a crowbar. Take out the ignition coil from the spark plug well.
- Step 7Clean dirt, dust and debris from inside the spark plug wells.
- Step 8Unscrew the spark plugs. Use the spark plug socket #16. Use a ratchet wrench.
- Step 9Take out the spark plugs. Use a telescoping magnet.
- Step 10Apply a thin layer of a special high temperature anti-seize lubricant to the threads of the new spark plugs.
- Step 11Install the new spark plugs into their mounting seats. Use the spark plug socket #16.
- Step 12Screw new spark plugs and tighten them. Use the spark plug socket #16. Use a torque wrench. Tighten it to 25 nm torque.Replacement: spark plugs – VAUXHALL ADAM. AUTODOC experts recommend:Don't tighten the plugs with excessive force. Exceeding tightening torque can damage the thread connection. Be careful when working with a spark plug wrench. Its skewing can cause damage to the threaded connection.
- Step 13Treat the ignition coil tips. Use high-temperature grease. Use a flat screwdriver.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the VAUXHALL Adam (M13) model
Popular maintenance tutorials for Adam M13
Complete guides for changing the Engine spark plug on different VAUXHALL ADAM models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your VAUXHALL Adam (M13)
View more
- Top 5 Car Interior Cleaning Mistakes You Should Avoid | AUTODOC Tips
- How to fix your car with AUTODOC CLUB
- Why Is the Windscreen Washer Not Spraying? Solution
- 5 possible reasons why your car heater isn't working
Most commonly replaced car parts on VAUXHALL ADAM
Time to replace parts? Get even better deals in our Shop app.

SCAN ME