How to change spark plugs on RENAULT Clio III Hatchback (BR0/1, CR0/1) – replacement guide
downloads:
4
Views:
354
0
Users voted – 0
Recommended replacement interval for the part category Spark plug : 60000km
Important!
This replacement procedure can be used for:
RENAULT Clio III Hatchback (BR0/1, CR0/1) 1.6 16V (BR09, BR0T, CR09, CR0T),
RENAULT Clio III Hatchback (BR0/1, CR0/1) 1.4 16V,
RENAULT Clio III Hatchback (BR0/1, CR0/1) 1.6 16V (BR05, BR0B, BR0Y, BR15, BR1J, BR1M, BR1Y, CR0B,...
…
View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Spark Plug for Clio III Hatchback (BR0/1, CR0/1) and other RENAULT models
Replacement: spark plugs – RENAULT CLIO III (BR0/1, CR0/1). Professionals recommend:
The replacement procedure is the same for all spark plugs.
All work should be done with the engine stopped.
Replacement: spark plugs – RENAULT CLIO III (BR0/1, CR0/1). Take the following steps:
Step 1
Open the hood.
Step 2
Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.
Step 3
Unplug the connectors from the ignition coils.
Step 4
Unscrew the ignition coil bracket. Use a drive socket #10. Use a ratchet wrench.
Step 5
Take out the ignition coils from the spark plug wells.
Replacement: spark plugs – RENAULT CLIO III (BR0/1, CR0/1). Tip from AUTODOC experts:
Remember the sequence of steps for ignition coil demounting.
Step 6
Clean dirt, dust and debris from inside the spark plug wells.
Step 7
Unscrew the spark plugs. Use the spark plug socket #16. Use a ratchet wrench.
Step 8
Take out the spark plugs.
Step 9
Apply a thin layer of a special high temperature anti-seize lubricant to the threads of the new spark plugs.
Step 10
Install the new spark plugs into their mounting seats.
Step 11
Screw new spark plugs and tighten them. Use the spark plug socket #16. Use a torque wrench. Tighten it to 25 nm torque.
Replacement: spark plugs – RENAULT CLIO III (BR0/1, CR0/1). Tip:
Don't tighten the plugs with excessive force. Exceeding tightening torque can damage the thread connection. Be careful when working with a spark plug wrench. Its skewing can cause damage to the threaded connection.
Step 12
Install the ignition coils to the spark plug wells. Make sure you hear a click indicating that it is locked in place.
AUTODOC recommends:
Replacement: spark plugs – RENAULT CLIO III (BR0/1, CR0/1). Follow the installation steps.
Step 13
Tighten the fasteners of the ignition coils. Use a drive socket #10.
Step 14
Treat the ignition coil connector with electronic spray. The spray will protect the electrical contacts from corrosion, oxidation, and will reduce the contact resistance.
Step 15
Plug in the connectors of the ignition coils. Make sure you hear a click indicating that it is locked in place.
Step 16
Run the engine for a few minutes. This is necessary in order to make sure that the component operates properly.
Step 17
Shut off the engine.
Step 18
Remove the fender protection cover.
Step 19
Close the hood.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents
Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
Scan
To download the app:
- scan the QR code
- download from App Store
- download from Google Play
Tips & tricks for your RENAULT Clio III Hatchback (BR0/1, CR0/1)