How to change spark plugs on Ford Mondeo BWY – replacement guide
downloads:
10
Views:
130
0
Users voted – 0
Recommended replacement interval for the part category Spark plug : 3year / 60000km
Important!
This replacement procedure can be used for:
FORD MONDEO III Estate (BWY) 1.8 16V,
FORD MONDEO III Estate (BWY) 2.0 16V,
FORD MONDEO III Estate (BWY) 1.8 SCi
…
View more
The steps may slightly vary depending on the car design.
How to change spark plug on FORD MONDEO 3 TUTORIAL | AUTODOC
All the parts you need to replace – Spark Plug for MONDEO III Estate (BWY) and other FORD models
Replacement: spark plugs – Ford Mondeo BWY. AUTODOC recommends:
The replacement procedure is the same for all spark plugs.
All work should be done with the engine stopped.
Replacement: spark plugs – Ford Mondeo BWY. Take the following steps:
Step 1
Open the hood.
Step 2
Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.
Step 3
Remove the engine cover.
Replacement: spark plugs – Ford Mondeo BWY. Tip from AUTODOC:
Raise the engine cover, holding it on two sides simultaneously.Do not apply excessive force when removing the part. Otherwise you may damage it.
Step 4
Remove the spark plug wire connectors from the spark plug wells. Use a flat screwdriver.
Replacement: spark plugs – Ford Mondeo BWY. AUTODOC experts recommend:
Be careful to avoid damaging spark plug wires.Remember the sequence of the spark plug wires connectors.
Step 5
Clean dirt, dust and debris from inside the spark plug wells.
Step 6
Unscrew the spark plugs. Use the spark plug socket #16. Use a ratchet wrench.
Step 7
Take out the spark plugs. Use the spark plug socket #16.
Step 8
Apply a thin layer of a special high temperature anti-seize lubricant to the threads of the new spark plugs.
Step 9
Install the new spark plugs into their mounting seats. Use the spark plug socket #16.
Step 10
Screw new spark plugs and tighten them. Use the spark plug socket #16. Use a torque wrench. Tighten it to 20 nm torque.
Step 11
Install the spark plug wire connectors into the spark plug wells. Make sure you hear a click indicating that it is locked in place.
AUTODOC recommends:
Replacement: spark plugs – Ford Mondeo BWY. Follow the installation steps.
Step 12
Install the engine cover and secure it.
Replacement: spark plugs – Ford Mondeo BWY. Professionals recommend:
Make sure the engine cover is properly seated. It should not be displaced with respect to the guiding fasteners.Do not apply excessive force when installing the part. Otherwise you may damage the fasteners.
Step 13
Remove the fender protection cover.
Step 14
Close the hood.
Step 15
Run the engine for a few minutes. This is necessary in order to make sure that the component operates properly.
Step 16
Shut off the engine.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Searching for the right tyres?
Find out which tyre and wheel sizes are compatible with the FORD Mondeo Mk3 Estate (BWY) model.
It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents
Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
Scan
To download the app:
- scan the QR code
- download from App Store
- download from Google Play
Tips & tricks for your FORD MONDEO III Estate (BWY)
View more
How to Prevent Premature Wear on Your Car Boot Damper | AUTODOC
Fuse Replacement Made Simple: Step-by-Step Guide | AUTODOC
Top Automatic Transmission Blunders You Must Dodge | AUTODOC Insights
Extend your engine's life: Avoid these 3 damaging factors | AUTODOC tips