Important!
This replacement procedure can be used for:
VW Passat Saloon (362) 1.4 TSI, VW Passat Saloon (362) 1.8 TSI, VW Passat Saloon (362) 2.0 TSI, VW Passat Saloon (362) 1.6 TDI, VW Passat Saloon (362) 2.0 TDI, VW Passat Saloon (362) 1.4 TSI EcoFuel, VW Passat Saloon (362) 1.4 TSI MultiFuel, VW Passat Saloon (362) 2.0 TDI, VW Passat Saloon (362) 1.8 TSI, VW Passat Saloon (362) 2.0 TDI, VW Passat Saloon (362) 1.4 TSI View more

The steps may slightly vary depending on the car design.

How to change rear wheel bearing on VW PASSAT B7 Saloon [TUTORIAL AUTODOC]

video
All the parts you need to replace – Wheel Bearing for Passat Saloon (362) and other VW models
How to change Wheel bearing kit on VW Passat B7 Saloon 2.0 TDI – step-by-step instructions for straightforward car repair
Wheel bearing kit
How to change Wheel bearing on VW Passat B7 Saloon 2.0 TDI – step-by-step instructions for straightforward car repair
Wheel bearing
Tools
Replacement: wheel bearing – VW Passat B7 saloon. Tools you need:
Wire brush
WD-40 spray
Brake cleaner
All-purpose cleaning spray
Sealant
Copper grease
Torque wrench
XZN socket bit # 14
XZN socket bit # 18
Torx bit T27
Torx bit T30
Wheel impact socket #17
Tap wrench
Hammer
Rubber mallet
Impact screwdriver
Bush and bearing driver set
Crow bar
Wheel chock
AUTODOC recommends:
  • Do not re-use the bearing assembly of your VW Passat B7 saloon car.
  • The wheel hub bearing replacement procedure is identical for both wheels on the same axle.
  • Please note: all work on the car – VW Passat B7 saloon – should be done with the engine switched off.
Carry out replacement in the following order:
  1. Step 1
    How to change Wheel Bearing on VW Passat B7 Saloon 2010 - free PDF and video manuals
    Connect the scan and service tool.
  2. Step 2
    How to replace VW Passat Saloon (362) 2.0 TDI 2011 Wheel Bearing - step-by-step manuals and video guides
    Put the parking brake system into service mode.
  3. Step 3
    VW Passat B7 Saloon 1.6 TDI 2012 Wheel Bearing replacement: free workshop manuals
    Open the hood.
  4. Step 4
    Clean the brake fluid reservoir cap. Use a brake cleaner.
    AUTODOC recommends:
    Replacement: wheel bearing – VW Passat B7 saloon. After applying the spray, wait a few minutes.
    Step 5
    Changing Wheel Bearing on VW Passat Saloon (362) 1.8 TSI 2013 by yourself
    Unscrew the engine solenoid valve bracket. Use Torx T27. Use a ratchet wrench.
  5. Step 6
    How to remove VW PASSAT 1.4 TSI EcoFuel 2014 Wheel Bearing - online easy-to-follow instructions
    Unscrew the brake fluid reservoir cap.
  6. Step 7
    Secure the wheels with chocks.
    Step 8
    How to replace Wheel Bearing on VW Passat Saloon (362) 2010: download PDF manuals and video instructions
    Loosen the wheel mounting bolts. Use wheel impact socket #17.
  7. Step 9
    How hard is it to do yourself: Wheel Bearing replacement on VW Passat B7 Saloon 2.0 TSI 2011 - download illustrated guide
    Raise the rear of the car and secure on supports.
  8. Step 10
    Need to know how to renew Wheel Bearing on VW PASSAT 2012? This free workshop manual will help you to do it yourself
    Unscrew the wheel bolts.
    AUTODOC recommends:
    Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. VW Passat B7 saloon
  9. Step 11
    Changing of Wheel Bearing on VW Passat B7 Saloon 2013 won't be an issue if you follow this illustrated step-by-step guide
    Remove the wheel.
  10. Step 12
    VW PASSAT 1.6 TDI Wheel Bearing replacement: online guides and video tutorials
    Spread the brake pads. Use a crowbar.
  11. Step 13
    Replacing Wheel Bearing on VW Passat B7 Saloon 2010 2.0 TDI by yourself
    Clean the brake caliper bracket fasteners. Use a wire brush. Use WD-40 spray.
  12. Step 14
    Passat Saloon (362) 1.4 TSI EcoFuel 2011 Wheel Bearing DIY replacement workshop manual
    Unscrew the caliper bracket fastening. Use XZN #14. Use a tap wrench.
  13. Step 15
    How to change Wheel Bearing on VW Passat Saloon (362) 2012 - tips and tricks
    Remove the brake caliper together with its bracket.
    Replacement: wheel bearing – VW Passat B7 saloon. Professionals recommend:
    Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur. Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary.
  14. Step 16
    Step-by-step recommendations for DIY replacement VW Passat B7 Saloon 2013 1.4 TSI EcoFuel Wheel Bearing
    Clean the brake disc fastener. Use a wire brush. Use WD-40 spray.
  15. Step 17
    DIY replacement of Wheel Bearing on VW Passat Saloon (362) 1.4 TSI 2014 is not an issue anymore with our step-by-step tutorial
    Unscrew the brake disc fastening. Use Torx T30. Use an impact screwdriver.
  16. Step 18
    How to change Wheel Bearing on VW Passat B7 Saloon 2010 - free PDF and video manuals
    Remove the brake disc. Use a rubber mallet.
  17. Step 19
    How to replace VW Passat Saloon (362) 2.0 TDI 2011 Wheel Bearing - step-by-step manuals and video guides
    Remove the hub bearing protection cap. Use a hammer. Use a crowbar.
    Please note!
    Some cars are not equipped with wheel hub caps.
  18. Step 20
    VW Passat B7 Saloon 1.6 TDI 2012 Wheel Bearing replacement: free workshop manuals
    Unscrew the hub bearing mounting. Use XZN #16. Use a tap wrench.
  19. Step 21
    Changing Wheel Bearing on VW Passat Saloon (362) 1.8 TSI 2013 by yourself
    Remove the fastening bolt.
  20. Step 22
    How to remove VW PASSAT 1.4 TSI EcoFuel 2014 Wheel Bearing - online easy-to-follow instructions
    Remove the hub and the bearing together, since they are a sealed unit.
  21. Step 23
    How to replace Wheel Bearing on VW Passat Saloon (362) 2010: download PDF manuals and video instructions
    Clean the hub bearing mounting seat. Use a wire brush. Use all-purpose cleaning spray.
  22. Step 24
    How hard is it to do yourself: Wheel Bearing replacement on VW Passat B7 Saloon 2.0 TSI 2011 - download illustrated guide
    Install the new wheel hub with a bearing. Use a bush and bearing driver set. Use a hammer.
  23. Step 25
    Need to know how to renew Wheel Bearing on VW PASSAT 2012? This free workshop manual will help you to do it yourself
    Treat the fasteners of the wheel hub bearing. Use a sealant.
  24. Step 26
    Changing of Wheel Bearing on VW Passat B7 Saloon 2013 won't be an issue if you follow this illustrated step-by-step guide
    Install the fastening bolt.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
VW Passat Saloon (362) Wheel Bearing replace by yourself - Scan QR-code and download AUTODOC CLUB app
Scan

To download the app:

  • - scan the QR code
  • - download from App Store
  • - download from Google Play
DIY VW Passat Saloon (362) Wheel Bearing replacement - online guide
Tips & tricks for your VW Passat Saloon (362)
View more
  • How to change Wheel bearings on VW Passat Saloon (362) 1.4 TSI - replacement tricks
    How to easily repair a punctured tyre | AUTODOC tips
  • Changing Hub bearing VW Passat B7 Saloon 2.0 TDI - Replacement Tips
    Top 5 tips to prevent car rust | AUTODOC tips
  • Maintenance Hacks - VW Passat Saloon (362) 1.6 TDI Wheel bearing kit replacement guide
    How and why to check your oil | AUTODOC tips
  • Replace Wheel hub bearing on VW Passat B7 Saloon - free video tips
    How to polish an old engine valve cover to a shiny finish | AUTODOC Tips