Disclaimer
How to change rear wheel bearing on VW Caddy 3 Kombi – replacement guide
downloads:
21
Views:
727
Important!
This replacement procedure can be used for:
VW Caddy III Estate (2KB, 2KJ, 2CB, 2CJ) 1.6 BiFuel, VW Caddy III Estate (2KB, 2KJ, 2CB, 2CJ) 2.0 TDI, VW Caddy III Estate (2KB, 2KJ, 2CB, 2CJ) 2.0 TDI, VW Caddy III Estate (2KB, 2KJ, 2CB, 2CJ) 1.6, VW Caddy III Estate (2KB, 2KJ, 2CB, 2CJ) 2.0 SDI, VW Caddy III Estate (2KB, 2KJ, 2CB, 2CJ) 1.9 TDI, VW Caddy III Estate (2KB, 2KJ, 2CB, 2CJ) 1.9 TDI, VW Caddy III Estate (2KB, 2KJ, 2CB, 2CJ) 2.0 EcoFuel, VW Caddy III Estate (2KB, 2KJ, 2CB, 2CJ) 1.4, VW Caddy III Estate (2KB, 2KJ, 2CB, 2CJ) 2.0 TDI, VW Caddy III Estate (2KB, 2KJ, 2CB, 2CJ) 1.2 TSI, VW Caddy III Estate (2KB, 2KJ, 2CB, 2CJ) 1.2 TSI, VW Caddy III Estate (2KB, 2KJ, 2CB, 2CJ) 2.0 TDI 16V, VW Caddy III Estate (2KB, 2KJ, 2CB, 2CJ) 1.6 TDI, VW Caddy III Estate (2KB, 2KJ, 2CB, 2CJ) 1.6 TDI … View more
The steps may slightly vary depending on the car design.
VW Caddy III Estate (2KB, 2KJ, 2CB, 2CJ) 1.6 BiFuel, VW Caddy III Estate (2KB, 2KJ, 2CB, 2CJ) 2.0 TDI, VW Caddy III Estate (2KB, 2KJ, 2CB, 2CJ) 2.0 TDI, VW Caddy III Estate (2KB, 2KJ, 2CB, 2CJ) 1.6, VW Caddy III Estate (2KB, 2KJ, 2CB, 2CJ) 2.0 SDI, VW Caddy III Estate (2KB, 2KJ, 2CB, 2CJ) 1.9 TDI, VW Caddy III Estate (2KB, 2KJ, 2CB, 2CJ) 1.9 TDI, VW Caddy III Estate (2KB, 2KJ, 2CB, 2CJ) 2.0 EcoFuel, VW Caddy III Estate (2KB, 2KJ, 2CB, 2CJ) 1.4, VW Caddy III Estate (2KB, 2KJ, 2CB, 2CJ) 2.0 TDI, VW Caddy III Estate (2KB, 2KJ, 2CB, 2CJ) 1.2 TSI, VW Caddy III Estate (2KB, 2KJ, 2CB, 2CJ) 1.2 TSI, VW Caddy III Estate (2KB, 2KJ, 2CB, 2CJ) 2.0 TDI 16V, VW Caddy III Estate (2KB, 2KJ, 2CB, 2CJ) 1.6 TDI, VW Caddy III Estate (2KB, 2KJ, 2CB, 2CJ) 1.6 TDI … View more
The steps may slightly vary depending on the car design.
How to change rear wheel bearing / rear hub bearing on VW CADDY 3 (2KB) [TUTORIAL AUTODOC]

All the parts you need to replace – Wheel Bearing for Caddy III Estate (2KB, 2KJ, 2CB, 2CJ) and other VW models
Alternative products

Wire brush
WD-40 spray
Brake cleaner
Copper grease
Multipurpose grease
Torx bit T30
HEX bit No.H19
Drive socket # 16
Wheel impact socket #17
Ratchet wrench
Torque wrench
3-Arm Gear Puller
Flat Screwdriver
Round-nose pliers
Flat chisel
Hammer
Rubber mallet
Crow bar
Wheel chock
Replacement: wheel bearing – VW Caddy 3 Kombi. AUTODOC recommends:
- The replacement procedure is identical for the left and right wheel hubs on the same axle.
- Please note: all work on the car – VW Caddy 3 Kombi – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1
Secure the wheels with chocks. - Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #17. - Step 3
Raise the rear of the car and secure on supports. - Step 4
Unscrew the wheel bolts.AUTODOC recommends:Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. VW Caddy 3 Kombi - Step 5
Remove the wheel. - Step 6
Spread the brake pads. Use a crowbar. - Step 7
Disconnect the ABS sensor electric socket. Disconnect the brake pad wear sensor plug. Remove the ABS sensor connector. Remove the connector of the brake pad wear sensor. Use round-nose pliers. - Step 8
Clean the brake caliper bracket fasteners. Use a wire brush. Use WD-40 spray.Please note!Some cars are not equipped with the brake pad wear sensor. - Step 9Unscrew the caliper bracket fastening. Use a drive socket #16. Use a ratchet wrench. Remove the brake caliper together with its bracket.Replacement: wheel bearing – VW Caddy 3 Kombi. Tip from AUTODOC experts:Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur.Step 10
Unscrew the brake disc mounting bolts and remove it. Use Torx T30.Replacement: wheel bearing – VW Caddy 3 Kombi. Tip:If necessary, use a rubber mallet. - Step 11
Pry the hub cap with a screwdriver and remove it. If necessary, use a flat chisel and a hammer. - Step 12
Unscrew the wheel hub axle nut. Use HEX No.19. - Step 13
Remove the hub and the bearing together, since they are a sealed unit. Use 3-Arm Gear Puller. - Step 14
Clean the guiding part of the stub axle. Use a wire brush.Replacement: wheel bearing – VW Caddy 3 Kombi. AUTODOC experts recommend:Be careful to avoid damaging the guiding part of the stub axle. - Step 15
Clean the hub bearing mounting seat. Use a wire brush. Use WD-40 spray. Apply special grease to the bearing assembly mounting seat. - Step 16
Install the new wheel hub with a bearing. Move the hub as far as it can go. - Step 17
Tighten the hub. Use HEX No.19. Use a torque wrench. Tighten it to 180 Nm torque.+180°Replacement: wheel bearing – VW Caddy 3 Kombi. AUTODOC recommends:Important! Be sure to use new fasteners.The wheel bearing unit must not tilt on the axle pin.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the VW Caddy III Estate (2KB, 2KJ, 2CB, 2CJ) model
Popular maintenance tutorials for VW Caddy 3
Complete guides for changing the Wheel bearings on different VW CADDY models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your VW Caddy III Estate (2KB, 2KJ, 2CB, 2CJ)
View more
TOP 5 mistakes when replacing shock absorbers | AUTODOC tips
Kolbenschmidt plastic gauge overview
Stop Rust Before It Starts: Top 5 Tips for Car Body Protection | AUTODOC Insights
How to remove rust | AUTODOC tips
Most commonly replaced car parts on VW CADDY
Time to replace parts? Get even better deals in our Shop app.

SCAN ME

































