Important!
This replacement procedure can be used for:
TOYOTA Yaris / Vios Saloon (_P9_) 1.5 (NCP93), TOYOTA Yaris / Vios Saloon (_P9_) 1.3 (NCP92_, SCP92_) View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

Tools
Replacement: wheel bearing – TOYOTA VIOS/YARIS Saloon (ZSP9_, NCP9_). Tools you'll need:
Wire brush
Nylon cleaning brush
WD-40 spray
All-purpose cleaning spray
Brake cleaner
Electronic spray
Anti-squeal paste
Ceramic grease
Copper grease
Torque wrench
Drive socket # 14
HEX bit No.H7
Wheel impact socket #21
Ratchet wrench
Flat screwdriver
Hammer
Crow bar
Hydraulic transmission jack
Wheel chock
AUTODOC recommends:
  • Do not re-use the bearing assembly of your TOYOTA VIOS/YARIS Saloon (ZSP9_, NCP9_) car.
  • The wheel hub bearing replacement procedure is identical for both wheels on the same axle.
  • Please note: all work on the car – TOYOTA VIOS/YARIS Saloon (ZSP9_, NCP9_) – should be done with the engine switched off.
Carry out replacement in the following order:
  1. Step 1
    Open the bonnet. Unscrew the brake fluid reservoir cap.
    Step 2
    Secure the wheels with chocks.
    Step 3
    How to change Wheel Bearing on TOYOTA VIOS/YARIS Saloon (ZSP9_, NCP9_) 2005 - free PDF and video manuals
    Loosen the wheel mounting bolts. Use wheel impact socket #21.
  2. Step 4
    Raise the car.
    Replacement: wheel bearing – TOYOTA VIOS/YARIS Saloon (ZSP9_, NCP9_). Tip from AUTODOC experts:
    If you are using a jack, make sure it rests on a flat surface without any unevenness.Be sure to additionally secure the car with jack stands.
    Step 5
    How to replace TOYOTA Yaris / Vios Saloon (_P9_) 1.0 (KSP92_) 2006 Wheel Bearing - step-by-step manuals and video guides
    Unscrew the wheel bolts.
    AUTODOC recommends:
    Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. TOYOTA VIOS/YARIS Saloon (ZSP9_, NCP9_)
  3. Step 6
    TOYOTA VIOS/YARIS Saloon (ZSP9_, NCP9_) 1.3 (NCP92_, SCP92_) 2007 Wheel Bearing replacement: free workshop manuals
    Remove the wheel.
  4. Step 7
    Changing Wheel Bearing on TOYOTA Yaris / Vios Saloon (_P9_) 1.5 (NCP93) 2008 by yourself
    Detach the brake caliper retaining spring. Use a crowbar.
  5. Step 8
    How to remove TOYOTA YARIS 1.3 4WD (NCP92_, NCP96_) 2009 Wheel Bearing - online easy-to-follow instructions
    Remove the dust boot caps of the brake caliper guide pins. Use a crowbar.
  6. Step 9
    How to replace Wheel Bearing on TOYOTA Yaris / Vios Saloon (_P9_) 2010: download PDF manuals and video instructions
    Unscrew the brake caliper fasteners. Use HEX No.H7. Use a ratchet wrench.
  7. Step 10
    How hard is it to do yourself: Wheel Bearing replacement on TOYOTA VIOS/YARIS Saloon (ZSP9_, NCP9_) 1.0 (KSP92_) 2011 - download illustrated guide
    Remove the brake caliper. Use a crowbar.
    Replacement: wheel bearing – TOYOTA VIOS/YARIS Saloon (ZSP9_, NCP9_). Tip:
    Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur.
  8. Step 11
    Need to know how to renew Wheel Bearing on TOYOTA YARIS 2012? This free workshop manual will help you to do it yourself
    Remove the brake pads.
  9. Step 12
    Changing of Wheel Bearing on TOYOTA VIOS/YARIS Saloon (ZSP9_, NCP9_) 2013 won't be an issue if you follow this illustrated step-by-step guide
    Clean the brake caliper bracket fasteners. Use a wire brush. Use WD-40 spray.
  10. Step 13
    TOYOTA YARIS 1.3 (NCP92_) Wheel Bearing replacement: online guides and video tutorials
    Unscrew the brake caliper bracket fasteners. Use a drive socket #14. Use a ratchet wrench.
  11. Step 14
    Replacing Wheel Bearing on TOYOTA VIOS/YARIS Saloon (ZSP9_, NCP9_) 2006 1.0 (KSP92_) by yourself
    Remove the fastening bolts.
  12. Step 15
    Yaris / Vios Saloon (_P9_) 1.3 4WD (NCP92_, NCP96_) 2007 Wheel Bearing DIY replacement workshop manual
    Remove the caliper bracket.
  13. Step 16
    How to change Wheel Bearing on TOYOTA Yaris / Vios Saloon (_P9_) 2008 - tips and tricks
    Remove the brake disc.
  14. Step 17
    Step-by-step recommendations for DIY replacement TOYOTA VIOS/YARIS Saloon (ZSP9_, NCP9_) 2009 1.3 4WD (NCP92_, NCP96_) Wheel Bearing
    Clean the ABS sensor fastener. Use a nylon cleaning brush. Use all-purpose cleaning spray.
  15. Step 18
    DIY replacement of Wheel Bearing on TOYOTA Yaris / Vios Saloon (_P9_) 1.3 (NCP92_) 2010 is not an issue anymore with our step-by-step tutorial
    Detach the ABS sensor connector. Use a flat screwdriver.
  16. Step 19
    How to change Wheel Bearing on TOYOTA VIOS/YARIS Saloon (ZSP9_, NCP9_) 2005 - free PDF and video manuals
    Clean the wheel hub fastener. Use a wire brush. Use WD-40 spray.
  17. Step 20
    How to replace TOYOTA Yaris / Vios Saloon (_P9_) 1.0 (KSP92_) 2006 Wheel Bearing - step-by-step manuals and video guides
    Support the rear suspension beam. Use a hydraulic transmission jack.
  18. Step 21
    TOYOTA VIOS/YARIS Saloon (ZSP9_, NCP9_) 1.3 (NCP92_, SCP92_) 2007 Wheel Bearing replacement: free workshop manuals
    Unscrew the wheel hub bearing fasteners. Use a drive socket #14. Use a ratchet wrench.
  19. Step 22
    Changing Wheel Bearing on TOYOTA Yaris / Vios Saloon (_P9_) 1.5 (NCP93) 2008 by yourself
    Remove the fastening bolts.
  20. Step 23
    How to remove TOYOTA YARIS 1.3 4WD (NCP92_, NCP96_) 2009 Wheel Bearing - online easy-to-follow instructions
    Remove the hub and the bearing together, since they are made as an assembly. Use a crowbar. Use a hammer.
  21. Step 24
    How to replace Wheel Bearing on TOYOTA Yaris / Vios Saloon (_P9_) 2010: download PDF manuals and video instructions
    Clean the hub bearing mounting seat. Use a wire brush. Use all-purpose cleaning spray.
  22. Step 25
    How hard is it to do yourself: Wheel Bearing replacement on TOYOTA VIOS/YARIS Saloon (ZSP9_, NCP9_) 1.0 (KSP92_) 2011 - download illustrated guide
    Treat the wheel hub mounting seat. Use copper grease.
  23. Step 26
    Need to know how to renew Wheel Bearing on TOYOTA YARIS 2012? This free workshop manual will help you to do it yourself
    Install the new wheel hub together with the bearing.
  24. Step 27
    Changing of Wheel Bearing on TOYOTA VIOS/YARIS Saloon (ZSP9_, NCP9_) 2013 won't be an issue if you follow this illustrated step-by-step guide
    Install the fastening bolts.
  25. Step 28
    TOYOTA YARIS 1.3 (NCP92_) Wheel Bearing replacement: online guides and video tutorials
    Tighten the wheel hub bearing fasteners. Use a drive socket #14. Use a torque wrench. Tighten it to 90 nm torque.
  26. Step 29
    Replacing Wheel Bearing on TOYOTA VIOS/YARIS Saloon (ZSP9_, NCP9_) 2006 1.0 (KSP92_) by yourself
    Treat the fasteners of the wheel hub bearing. Use copper grease.
  27. Step 30
    Yaris / Vios Saloon (_P9_) 1.3 4WD (NCP92_, NCP96_) 2007 Wheel Bearing DIY replacement workshop manual
    Remove the support from under the rear axle beam.
    AUTODOC recommends:
    Replacement: wheel bearing – TOYOTA VIOS/YARIS Saloon (ZSP9_, NCP9_). Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms.
  28. Step 31
    How to change Wheel Bearing on TOYOTA Yaris / Vios Saloon (_P9_) 2008 - tips and tricks
    Treat the hub where it contacts the brake disk. Use ceramic grease.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Searching for the right tyres?

Find out which tyre and wheel sizes are compatible with the TOYOTA Vios / Yaris II Saloon (XP9) model.

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
TOYOTA Yaris / Vios Saloon (_P9_) Wheel Bearing replace by yourself - Scan QR-code and download AUTODOC CLUB app
Scan

To download the app:

  • - scan the QR code
  • - download from App Store
  • - download from Google Play
DIY TOYOTA Yaris / Vios Saloon (_P9_) Wheel Bearing replacement - online guide
Tips & tricks for your TOYOTA Yaris / Vios Saloon (_P9_)
View more
  • How to change Wheel bearings on TOYOTA Yaris / Vios Saloon (_P9_) 1.3 (NCP92_) - replacement tricks
    Top 5 tips to prevent car rust | AUTODOC tips
  • Changing Hub bearing TOYOTA VIOS/YARIS Saloon (ZSP9_, NCP9_) 1.0 (KSP92_) - Replacement Tips
    Headlight Restoration | AUTODOC tips
  • Maintenance Hacks - TOYOTA Yaris / Vios Saloon (_P9_) 1.3 (NCP92_, SCP92_) Wheel bearing kit replacement guide
    TOP 8 mistakes car owners make | AUTODOC tips
  • Replace Wheel hub bearing on TOYOTA VIOS/YARIS Saloon (ZSP9_, NCP9_) - free video tips
    How to polish your car | AUTODOC tips