Disclaimer
How to change rear wheel bearing on RENAULT Sandero / Stepway I (BS_) – replacement guide
downloads:
13
Views:
261
Important!
This replacement procedure can be used for:
RENAULT Sandero / Stepway I (BS_) 1.6, RENAULT Sandero / Stepway I (BS_) 1.6 … View more
The steps may slightly vary depending on the car design.
RENAULT Sandero / Stepway I (BS_) 1.6, RENAULT Sandero / Stepway I (BS_) 1.6 … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Wheel Bearing for Sandero / Stepway I (BS_) and other RENAULT models
Alternative products

Wire brush
All-purpose cleaning spray
Ceramic grease
Torque wrench
Drive socket # 30
Wheel impact socket #17
Ratchet wrench
Tap wrench
Crow bar
Hammer
Circlip pliers
Bush and bearing driver set
Wheel chock
Replacement: wheel bearing – RENAULT SANDERO/STEPWAY I. Professionals recommend:
- Do not re-use the bearing assembly of your RENAULT SANDERO/STEPWAY I car.
- The wheel hub bearing replacement procedure is identical for both wheels on the same axle.
- All work should be done with the engine stopped.
Replacement: wheel bearing – RENAULT SANDERO/STEPWAY I. Take the following steps:
- Step 1Secure the wheels with chocks.Step 2
Loosen the wheel bolts. Use wheel impact socket #17. Use a tap wrench. - Step 3Raise the car.Replacement: wheel bearing – RENAULT SANDERO/STEPWAY I. AUTODOC experts recommend:If you are using a jack, make sure it rests on a flat surface without any unevenness.Be sure to additionally secure the car with jack stands.Step 4
Unscrew the wheel bolts.AUTODOC recommends:To avoid injury, hold up the wheel when unscrewing the bolts. - Step 5
Remove the wheel. - Step 6
Remove the hub bearing cap. Use a crowbar. Use a hammer. - Step 7
Unscrew the wheel hub fastener. Use a drive socket #30. Use a tap wrench. - Step 8
Remove the fastening nut. - Step 9
Remove the brake drum assembled with the wheel hub bearing.Replacement: wheel bearing – RENAULT SANDERO/STEPWAY I. Tip:Examine the brake drum. Replace it if necessary. - Step 10
Remove the wheel hub bearing retaining ring. Use circlip pliers. - Step 11
Press out the wheel hub bearing. Use a bush and bearing driver set. - Step 12
Clean the hub bearing mounting seat. Use a wire brush. - Step 13
Press fit the new wheel hub bearing into the brake drum. Use a bush and bearing driver set.AUTODOC recommends:Check to make sure the wheel hub bearing is positioned correctly. Avoid its misalignment.Stop pressing on the surface of the bearing immediately after it has been fitted into its mounting seat. - Step 14
Install the wheel hub bearing retaining ring. Use circlip pliers.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the RENAULT Sandero / Stepway I (BS_) model
Popular maintenance tutorials for RENAULT SANDERO/STEPWAY I
Complete guides for changing the Wheel bearings on different RENAULT SANDERO / STEPWAY models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your RENAULT Sandero / Stepway I (BS_)
View more
Petrol or diesel: The engine showdown! | AUTODOC
Top 7 signs of a bad starter
Transform Your Engine Bay: Affordable Valve Cover Restoration with AUTODOC
When, why, and how to change engine oil | AUTODOC tips
Most commonly replaced car parts on RENAULT SANDERO / STEPWAY
Time to replace parts? Get even better deals in our Shop app.

SCAN ME





























