Important!
This replacement procedure can be used for:
PEUGEOT 406 (8B) 1.6, PEUGEOT 406 (8B) 1.8 16V, PEUGEOT 406 (8B) 2.0 16V, PEUGEOT 406 (8B) 1.9 TD, PEUGEOT 406 (8B) 2.1 TD 12V, PEUGEOT 406 (8B) 2.0 Turbo, PEUGEOT 406 (8B) 1.9 TD, PEUGEOT 406 (8B) 3.0 24V, PEUGEOT 406 (8B) 1.8, PEUGEOT 406 (8B) 2.0 HDI 110, PEUGEOT 406 (8B) 2.0 HDI 90, PEUGEOT 406 (8B) 2.0 16V, PEUGEOT 406 (8B) 3.0 V6, PEUGEOT 406 (8B) 1.8 16V, PEUGEOT 406 (8B) 2.0 16V, PEUGEOT 406 (8B) 2.2 HDi, PEUGEOT 406 (8B) 1.9 D, PEUGEOT 406 (8B) 2.0 16V HPi, PEUGEOT 406 (8B) 2.0 HDi 110, PEUGEOT 406 (8B) 1.8, PEUGEOT 406 (8B) 2.0 View more

The steps may slightly vary depending on the car design.

How to change a Rear wheel bearing on PEUGEOT 406 TUTORIAL | AUTODOC

video
All the parts you need to replace – Wheel Bearing for 406 (8B) and other PEUGEOT models
How to change Wheel bearing kit on Peugeot 406 Saloon 2.0 HDI 110 – step-by-step instructions for straightforward car repair
Wheel bearing kit
How to change Wheel bearing on Peugeot 406 Saloon 2.0 HDI 110 – step-by-step instructions for straightforward car repair
Wheel bearing
How to change Cap, wheel bearing on Peugeot 406 Saloon 2.0 HDI 110 – step-by-step instructions for straightforward car repair
Cap, wheel bearing
Tools
Replacement: wheel bearing – Peugeot 406 saloon. Tools you'll need:
Wire brush
WD-40 spray
Brake cleaner
All-purpose cleaning spray
Copper grease
High-temperature ceramic grease
Torque wrench
Torx bit T30
HEX bit no.H7
Drive socket # 16
Drive socket # 41
Wheel impact socket #19
Ratchet wrench
Hammer
Flat chisel
Crow bar
Rubber mallet
Flat Screwdriver
Wheel chock
AUTODOC recommends:
  • Do not re-use the bearing assembly of your Peugeot 406 saloon car.
  • The wheel hub bearing replacement procedure is identical for both wheels on the same axle.
  • Please note: all work on the car – Peugeot 406 saloon – should be done with the engine switched off.
Carry out replacement in the following order:
  1. Step 1
    How to change Wheel Bearing on Peugeot 406 Saloon 1995 - free PDF and video manuals
    Open the bonnet. Unscrew the brake fluid reservoir cap.
  2. Step 2
    How to replace PEUGEOT 406 (8B) 2.0 HDI 110 1996 Wheel Bearing - step-by-step manuals and video guides
    Secure the wheels with chocks.
  3. Step 3
    Peugeot 406 Saloon 1.8 16V 1997 Wheel Bearing replacement: free workshop manuals
    Loosen the wheel mounting bolts. Use wheel impact socket #19.
  4. Step 4
    Changing Wheel Bearing on PEUGEOT 406 (8B) 2.1 TD 12V 1998 by yourself
    Raise the rear of the car and secure on supports.
  5. Step 5
    How to remove PEUGEOT 406 1.9 TD 1999 Wheel Bearing - online easy-to-follow instructions
    Unscrew the wheel bolts.
    AUTODOC recommends:
    Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. Peugeot 406 saloon
  6. Step 6
    How to replace Wheel Bearing on PEUGEOT 406 (8B) 2000: download PDF manuals and video instructions
    Remove the wheel.
  7. Step 7
    How hard is it to do yourself: Wheel Bearing replacement on Peugeot 406 Saloon 2.2 HDi 2001 - download illustrated guide
    Remove the dust boot caps of the brake caliper guide pins. Use a flat screwdriver.
  8. Step 8.1
    Need to know how to renew Wheel Bearing on PEUGEOT 406 2002? This free workshop manual will help you to do it yourself
    Unscrew the brake caliper fasteners. Use HEX No.H7.
    Step 8.2
    Changing of Wheel Bearing on Peugeot 406 Saloon 2003 won't be an issue if you follow this illustrated step-by-step guide
    Use a drive socket #16. Use a ratchet wrench.
  9. Step 9
    Remove the fastening bolts.
    Step 10
    Spread the brake pads. Use a crowbar.
    Step 11
    PEUGEOT 406 2.0 HDI 110 Wheel Bearing replacement: online guides and video tutorials
    Remove the brake caliper.
    Replacement: wheel bearing – Peugeot 406 saloon. Professionals recommend:
    Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur.
  10. Step 12
    Replacing Wheel Bearing on Peugeot 406 Saloon 2005 2.0 HDI 110 by yourself
    Clean the brake disc fasteners. Use a wire brush. Use WD-40 spray.
  11. Step 13
    406 (8B) 1.9 TD 1995 Wheel Bearing DIY replacement workshop manual
    Unscrew the brake disc fasteners. Use Torx T30. Use a ratchet wrench.
  12. Step 14
    How to change Wheel Bearing on PEUGEOT 406 (8B) 1996 - tips and tricks
    Remove the brake disc.
  13. Step 15
    Step-by-step recommendations for DIY replacement Peugeot 406 Saloon 1997 1.9 TD Wheel Bearing
    Remove the hub bearing protection cap. Use a crowbar. Use a rubber mallet.
  14. Step 16
    DIY replacement of Wheel Bearing on PEUGEOT 406 (8B) 2.0 HDI 90 1998 is not an issue anymore with our step-by-step tutorial
    Unstake the wheel hub retaining nut. Use a flat metal-working chisel. Use a hammer.
  15. Step 17
    How to change Wheel Bearing on Peugeot 406 Saloon 1995 - free PDF and video manuals
    Unscrew the wheel hub axle nut. Use a drive socket #41. Use a ratchet wrench.
  16. Step 18
    Remove the fastening nut.
    Step 19
    How to replace PEUGEOT 406 (8B) 2.0 HDI 110 1996 Wheel Bearing - step-by-step manuals and video guides
    Remove the hub and the bearing together, since they are a sealed unit.
  17. Step 20
    Peugeot 406 Saloon 1.8 16V 1997 Wheel Bearing replacement: free workshop manuals
    Clean the wheel hub mounting seat. Use all-purpose cleaning spray.
  18. Step 21
    Changing Wheel Bearing on PEUGEOT 406 (8B) 2.1 TD 12V 1998 by yourself
    Install the new wheel hub together with the bearing.
  19. Step 22
    How to remove PEUGEOT 406 1.9 TD 1999 Wheel Bearing - online easy-to-follow instructions
    Install the fastening nut.
  20. Step 23
    How to replace Wheel Bearing on PEUGEOT 406 (8B) 2000: download PDF manuals and video instructions
    Tighten the hub. Use a drive socket #41. Use a torque wrench. Tighten it to 275 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
PEUGEOT 406 (8B) Wheel Bearing replace by yourself - Scan QR-code and download AUTODOC CLUB app
Scan

To download the app:

  • - scan the QR code
  • - download from App Store
  • - download from Google Play
DIY PEUGEOT 406 (8B) Wheel Bearing replacement - online guide
Tips & tricks for your PEUGEOT 406 (8B)
View more
  • How to change Wheel bearings on PEUGEOT 406 (8B) 2.0 HDI 90 - replacement tricks
    What to do if your car's air conditioning isn't working properly | AUTODOC tips
  • Changing Hub bearing Peugeot 406 Saloon 2.0 HDI 110 - Replacement Tips
    DIY brake caliper restoration | AUTODOC tips
  • Maintenance Hacks - PEUGEOT 406 (8B) 1.8 16V Wheel bearing kit replacement guide
    5 tools that make car repair incredibly simple | AUTODOC tips
  • Replace Wheel hub bearing on Peugeot 406 Saloon - free video tips
    How to replace a wheel stud | AUTODOC tips