Important!

This replacement procedure can be used for:
PEUGEOT 307 SW (3H) 1.6 16V, PEUGEOT 307 SW (3H) 2.0 HDI, PEUGEOT 307 SW (3H) 2.0 HDI, PEUGEOT 307 SW (3H) 1.4 16V, PEUGEOT 307 SW (3H) 1.6 HDI, PEUGEOT 307 SW (3H) 2.0 16V, PEUGEOT 307 SW (3H) 1.6 HDI, PEUGEOT 307 SW (3H) 1.6 BioFlex … View more

The steps may slightly vary depending on the car design.

How to change rear wheel bearing on PEUGEOT 307 (3H) [TUTORIAL AUTODOC]

Alternative products

Wheel bearing kit

Replacement: wheel bearing – Peugeot 307 SW. Tools you'll need:

                      Wire brush
                    
                      All-purpose cleaning spray
                    
                      WD-40 spray
                    
                      Brake cleaner 
                    
                      Copper grease 
                    
                      Torque wrench
                    
                      Combination spanner #15
                    
                      Drive socket # 13 
                    
                      Drive socket # 32 
                    
                      Torx bit T50
                    
                      Wheel impact socket #17
                    
                      Ratchet wrench
                    
                      Tap wrench
                    
                      Hammer
                    
                      Flat chisel
                    
                      Pliers 
                    
                      Bush and bearing driver set
                    
                      Rubber mallet
                    
                      Flat Screwdriver
                    
                      Circlip pliers
                    
                      Hub slide hammer puller
                    
                      Water pump pliers
                    
                      Crow bar
                    
                      Wheel chock

Buy tools

Replacement: wheel bearing – Peugeot 307 SW. Professionals recommend:

Do not re-use the bearing assembly of your Peugeot 307 SW car.
The wheel hub bearing replacement procedure is identical for both wheels on the same axle.
All work should be done with the engine stopped.

Replacement: wheel bearing – Peugeot 307 SW. Use the following procedure:

Step 1

Secure the wheels with chocks.
Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 3

Raise the rear of the car and secure on supports.
Step 4

Unscrew the wheel bolts.

Replacement: wheel bearing – Peugeot 307 SW. AUTODOC recommends:
To avoid injury, hold up the wheel when unscrewing the bolts.
Step 5

Remove the wheel.
Step 6

Clean the brake caliper fasteners. Use a wire brush. Use WD-40 spray.
Step 7

Release the parking brake cable. Use water pump pliers. Use a flat screwdriver.
Step 8

Unscrew the brake caliper fastening. Use a combination spanner #15. Use a drive socket #13. Use a ratchet wrench.
Step 9

Spread the brake pads. Use a crowbar.
Step 10

Remove the brake caliper.

Replacement: wheel bearing – Peugeot 307 SW. AUTODOC experts recommend:
Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur. Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary.
Step 11

Remove the brake pads.
Step 12

Clean the brake caliper bracket fasteners. Use a wire brush. Use WD-40 spray.
Step 13

Unscrew the caliper bracket fastening. Use Torx T50. Use a tap wrench.
Step 14

Remove the caliper bracket.
Step 15

Clean the hub bearing protection cap. Use a wire brush. Use WD-40 spray.
Step 16

Remove the hub bearing protection cap. Use a hammer. Use a crowbar.

Replacement: wheel bearing – Peugeot 307 SW. Tip:
Some cars are not equipped with wheel hub caps.
Step 17

Unstake the fastener of the driveshaft. Use a flat metal-working chisel. Use a hammer.
Step 18

Unscrew the wheel hub axle nut. Use a drive socket #32. Use a tap wrench.
Step 19

Remove the brake disc assemled with the wheel hub bearing. Use the hub slide hammer puller.
Step 20

Clean the surface around the ABS tone ring. Use a wire brush. Use WD-40 spray.
Step 21

Remove the ABS tone ring. Use a crowbar.

Step 22

Remove the wheel hub bearing retaining ring. Use circlip pliers.
Step 23

Press out the wheel hub bearing. Use a bush and bearing driver set.
Step 24

Clean the hub bearing mounting seat. Use WD-40 spray.
Step 25

Press fit the new wheel hub bearing into the brake disc. Use a bush and bearing driver set.

Replacement: wheel bearing – Peugeot 307 SW. Professionals recommend:
Check to make sure the wheel hub bearing is positioned correctly. Avoid its misalignment. Stop pressing on the surface of the bearing immediately after it has been fitted into its mounting seat.
Step 26

Install the wheel hub bearing retaining ring. Use circlip pliers.
Step 27

Install the ABS tone ring.

Step 28

Clean the stub axle. Use a wire brush. Use all-purpose cleaning spray.
Step 29

Install the brake disc assembled with the wheel hub bearing.
Step 30

Tighten the hub. Use a drive socket #32. Use a torque wrench. Tighten it to 280 nm torque.

Replacement: wheel bearing – Peugeot 307 SW. Tip from AUTODOC:
The wheel bearing unit must not tilt on the axle pin.
Step 31

Restake the fastener of the driveshaft. Use a flat metal-working chisel. Use a hammer.
Step 32

Install the hub bearing protection cap. Use a rubber mallet.
Step 33

Clean the brake caliper bracket from dirt and dust. Use a wire brush. Use a brake cleaner.

AUTODOC recommends:
Replacement: wheel bearing – Peugeot 307 SW. After applying the spray, wait a few minutes.
Step 34

Install the brake caliper bracket.
Step 35

Tighten the brake caliper bracket. Use Torx T50. Use a torque wrench. Tighten it to 53 Nm torque.
Step 36

Install the brake pads.
Step 37

Install the brake caliper and fix it. Use a combination spanner #15. Use a drive socket #13. Use a torque wrench. Tighten it to 30 Nm torque.
Step 38

Install the parking brake cable into the brake caliper bracket. Use water pump pliers. Use pliers.
Step 39

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 40

Clean the brake disk surface. Use a brake cleaner.

Replacement: wheel bearing – Peugeot 307 SW. Tip from AUTODOC experts:
After applying the spray, wait a few minutes.
Step 41

Install the wheel.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. Peugeot 307 SW
Step 42

Screw in the wheel bolts. Use wheel impact socket #17.
Step 43

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #17. Use a torque wrench. Tighten it to 100 Nm torque.
Step 44

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the PEUGEOT 307 SW (3H) model

Peugeot 307 SW tyre size

How to change front wheel bearing on Peugeot 307 SW – replacement guide

Free download PDF
3.66 MB
How to change front ball joint on Peugeot 307 SW – replacement guide

Free download PDF
2.38 MB
How to change front lower arm on Peugeot 307 SW – replacement guide

Free download PDF
2.85 MB
How to change front anti roll bar links on Peugeot 307 SW – replacement guide

Free download PDF
1.33 MB
How to change track rod end on Peugeot 307 SW – replacement guide

Free download PDF
1.71 MB
How to change front brake pads on Peugeot 307 SW – replacement guide

Free download PDF
1.68 MB

How to change front wheel bearing on PEUGEOT 307 CC (3B) – replacement guide

Free download PDF
5.98 MB
How to change rear wheel bearing on PEUGEOT 307 CC (3B) – replacement guide

Free download PDF
2.15 MB
How to change front wheel bearing on PEUGEOT 307 Hatchback (3A/C) – replacement guide

Free download PDF
5.98 MB
How to change rear wheel bearing on PEUGEOT 307 Hatchback (3A/C) – replacement guide

Free download PDF
2.15 MB
How to change front wheel bearing on Peugeot 307 SW – replacement guide

Free download PDF
3.66 MB
How to change front wheel bearing on PEUGEOT 307 Estate (3E) – replacement guide

Free download PDF
5.98 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

Save Money on Fuel with These Easy Tips | AUTODOC

5K views

Published on: 27/09/2022
What causes engine misfire? | AUTODOC

6K views

Published on: 10/07/2020
Understanding Airbag Light Warnings | Essential Tips for Car Safety

6K views

Published on: 10/04/2023
How to inspect and troubleshoot your car heater when it’s not working

5K views

Published on: 11/02/2021