Important!
This replacement procedure can be used for:
PEUGEOT 307 Break (3E) 1.4 16V, PEUGEOT 307 Break (3E) 1.6 16V, PEUGEOT 307 Break (3E) 2.0 HDI 90, PEUGEOT 307 Break (3E) 2.0, PEUGEOT 307 Break (3E) 1.6 HDi 110, PEUGEOT 307 Break (3E) 2.0 HDi 135, PEUGEOT 307 Break (3E) 1.4 HDi, PEUGEOT 307 Break (3E) 2.0 16V, PEUGEOT 307 Break (3E) 2.0 16V, PEUGEOT 307 Break (3E) 2.0 HDI 110, PEUGEOT 307 Break (3E) 1.6 HDi, PEUGEOT 307 Break (3E) 1.4, PEUGEOT 307 Break (3E) 1.6 BioFlex View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

Tools
Replacement: wheel bearing – PEUGEOT 307 Break (3E). Tools you might need:
Wire brush
WD-40 spray
All-purpose cleaning spray
Brake cleaner
Electronic spray
Multipurpose grease
Copper grease
Torque wrench
Combination spanner #13
Combination spanner #17
Drive socket # 13
Drive socket # 16
Drive socket # 17
Drive socket # 35
Torx bit T30
Torx bit T55
Wheel impact socket #17
Bush and bearing driver set
Ratchet wrench
Tap wrench
Hammer
Clip removal tool
Circlip pliers
Impact screwdriver
Flat Screwdriver
Crow bar
Hydraulic transmission jack
Bearing separator
Vice
Ball joint puller
Wheel chock
Replacement: wheel bearing – PEUGEOT 307 Break (3E). Tip from AUTODOC experts:
  • Do not re-use the bearing assembly of your PEUGEOT 307 Break (3E) car.
  • The wheel hub bearing replacement procedure is identical for both wheels on the same axle.
  • All work should be done with the engine stopped.
Replacement: wheel bearing – PEUGEOT 307 Break (3E). Take the following steps:
  1. Step 1
    How to change Wheel Bearing on Peugeot 307 Estate 2002 - free PDF and video manuals
    Secure the wheels with chocks.
  2. Step 2
    How to replace PEUGEOT 307 Break (3E) 1.6 16V 2003 Wheel Bearing - step-by-step manuals and video guides
    Loosen the wheel mounting bolts. Use wheel impact socket #17.
  3. Step 3
    Raise the front of the car and secure on supports.
    Step 4
    Peugeot 307 Estate 1.6 HDi 110 2004 Wheel Bearing replacement: free workshop manuals
    Unscrew the wheel bolts.
    AUTODOC recommends:
    Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. PEUGEOT 307 Break (3E)
  4. Step 5
    Changing Wheel Bearing on PEUGEOT 307 Break (3E) 2.0 HDI 90 2005 by yourself
    Remove the wheel.
  5. Step 6
    How to remove PEUGEOT 307 2.0 HDI 110 2006 Wheel Bearing - online easy-to-follow instructions
    Remove the CV axle nut cotter pin. Use a crowbar.
  6. Step 7
    How to replace Wheel Bearing on PEUGEOT 307 Break (3E) 2007: download PDF manuals and video instructions
    Loosen the fastener of the driveshaft. Use a drive socket #35. Use a tap wrench.
  7. Step 8
    How hard is it to do yourself: Wheel Bearing replacement on Peugeot 307 Estate 2.0 2008 - download illustrated guide
    Remove the fastening nut.
  8. Step 9
    Need to know how to renew Wheel Bearing on PEUGEOT 307 2009? This free workshop manual will help you to do it yourself
    Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray.
  9. Step 10
    Changing of Wheel Bearing on Peugeot 307 Estate 2002 won't be an issue if you follow this illustrated step-by-step guide
    Unscrew the fastener connecting the stabilizer link to the shock strut. Use a drive socket #17. Use a ratchet wrench.
  10. Step 11
    PEUGEOT 307 2.0 HDi 135 Wheel Bearing replacement: online guides and video tutorials
    Remove the stabilizer rod.
  11. Step 12
    Replacing Wheel Bearing on Peugeot 307 Estate 2004 1.6 16V by yourself
    Clean the fastener of the bracket that connects the brake hose to the shock strut. Use a wire brush. Use WD-40 spray.
  12. Step 13
    307 Break (3E) 2.0 HDI 110 2005 Wheel Bearing DIY replacement workshop manual
    Unscrew the brake hose fastening bracket from the shock strut. Use a combination spanner #13.
  13. Step 14
    How to change Wheel Bearing on PEUGEOT 307 Break (3E) 2006 - tips and tricks
    Disconnect the brake hose mounting bracket.
  14. Step 15
    Step-by-step recommendations for DIY replacement Peugeot 307 Estate 2007 2.0 HDI 110 Wheel Bearing
    Spread the brake pads. Use a crowbar.
  15. Step 16
    DIY replacement of Wheel Bearing on PEUGEOT 307 Break (3E) 1.6 HDi 2008 is not an issue anymore with our step-by-step tutorial
    Clean the brake caliper bracket fasteners. Use a wire brush. Use WD-40 spray.
  16. Step 17
    How to change Wheel Bearing on Peugeot 307 Estate 2002 - free PDF and video manuals
    Unscrew the caliper bracket fastening. Use Torx T55. Use a tap wrench. Use a ratchet wrench.
  17. Step 18
    How to replace PEUGEOT 307 Break (3E) 1.6 16V 2003 Wheel Bearing - step-by-step manuals and video guides
    Remove the brake caliper together with its bracket.
    Replacement: wheel bearing – PEUGEOT 307 Break (3E). Professionals recommend:
    Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur.Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary.
  18. Step 19
    Peugeot 307 Estate 1.6 HDi 110 2004 Wheel Bearing replacement: free workshop manuals
    Disconnect the ABS sensor wiring.
  19. Step 20
    Changing Wheel Bearing on PEUGEOT 307 Break (3E) 2.0 HDI 90 2005 by yourself
    Remove the plastic clips of the wheel arch liner. Use a clip removal tool.
  20. Step 21
    How to remove PEUGEOT 307 2.0 HDI 110 2006 Wheel Bearing - online easy-to-follow instructions
    Remove the wheel arch cover.
  21. Step 22
    How to replace Wheel Bearing on PEUGEOT 307 Break (3E) 2007: download PDF manuals and video instructions
    Detach the ABS sensor connector.
  22. Step 23
    How hard is it to do yourself: Wheel Bearing replacement on Peugeot 307 Estate 2.0 2008 - download illustrated guide
    Unscrew the brake disc fastening. Use Torx T30. Use an impact screwdriver.
  23. Step 24
    Need to know how to renew Wheel Bearing on PEUGEOT 307 2009? This free workshop manual will help you to do it yourself
    Remove the brake disc.
  24. Step 25
    Changing of Wheel Bearing on Peugeot 307 Estate 2002 won't be an issue if you follow this illustrated step-by-step guide
    Unscrew the end fastening nut to the steering knuckle. Use a drive socket #17. Use a ratchet wrench.
  25. Step 26
    PEUGEOT 307 2.0 HDi 135 Wheel Bearing replacement: online guides and video tutorials
    Disconnect the tie rod end from the steering knuckle. Use a ball joint puller.
  26. Step 27
    Replacing Wheel Bearing on Peugeot 307 Estate 2004 1.6 16V by yourself
    Clean all joints of the arm. Use a wire brush. Use WD-40 spray.
  27. Step 28
    307 Break (3E) 2.0 HDI 110 2005 Wheel Bearing DIY replacement workshop manual
    Unscrew the fasteners connecting the ball joint to the control arm. Use a combination spanner #17. Use a drive socket #16. Use a ratchet wrench.
  28. Step 29
    How to change Wheel Bearing on PEUGEOT 307 Break (3E) 2006 - tips and tricks
    Disconnect the ball joint from the arm. Use a crowbar.
  29. Step 30
    Step-by-step recommendations for DIY replacement Peugeot 307 Estate 2007 2.0 HDI 110 Wheel Bearing
    Clean the fasteners connecting the shock strut to the steering knuckle. Use a wire brush. Use WD-40 spray.
  30. Step 31
    DIY replacement of Wheel Bearing on PEUGEOT 307 Break (3E) 1.6 HDi 2008 is not an issue anymore with our step-by-step tutorial
    Unscrew the lower fastener connecting the shock strut to the steering knuckle. Use a drive socket #16. Use a ratchet wrench.
  31. Step 32
    How to change Wheel Bearing on Peugeot 307 Estate 2002 - free PDF and video manuals
    Remove the fastening bolt.
  32. Step 33
    How to replace PEUGEOT 307 Break (3E) 1.6 16V 2003 Wheel Bearing - step-by-step manuals and video guides
    Detach the driveshaft from the steering knuckle.
  33. Step 34
    Peugeot 307 Estate 1.6 HDi 110 2004 Wheel Bearing replacement: free workshop manuals
    Disconnect the steering knuckle from the shock absorber strut. Use a hammer.
  34. Step 35
    Changing Wheel Bearing on PEUGEOT 307 Break (3E) 2.0 HDI 90 2005 by yourself
    Remove the steering knuckle together with the hub.
  35. Step 36
    How to remove PEUGEOT 307 2.0 HDI 110 2006 Wheel Bearing - online easy-to-follow instructions
    Place the steering knuckle assembled with the wheel hub in a vice.
  36. Step 37
    How to replace Wheel Bearing on PEUGEOT 307 Break (3E) 2007: download PDF manuals and video instructions
    Clean the ABS sensor mounting seat. Use a wire brush. Use WD-40 spray.
  37. Step 38
    How hard is it to do yourself: Wheel Bearing replacement on Peugeot 307 Estate 2.0 2008 - download illustrated guide
    Unscrew the ABS sensor fastener. Use a drive socket #13. Use a ratchet wrench.
  38. Step 39
    Need to know how to renew Wheel Bearing on PEUGEOT 307 2009? This free workshop manual will help you to do it yourself
    Disconnect the ABS sensor. Use a flat screwdriver.
  39. Step 40
    Changing of Wheel Bearing on Peugeot 307 Estate 2002 won't be an issue if you follow this illustrated step-by-step guide
    Clean the wheel hub bearing retaining ring. Use a wire brush. Use WD-40 spray.
  40. Step 41
    PEUGEOT 307 2.0 HDi 135 Wheel Bearing replacement: online guides and video tutorials
    Remove the wheel hub bearing retaining ring. Use circlip pliers.
  41. Step 42
    Release the vice and remove the steering knuckle assembled with the wheel hub.
    Step 43
    Replacing Wheel Bearing on Peugeot 307 Estate 2004 1.6 16V by yourself
    Remove the wheel hub from the steering knuckle. Use a bush and bearing driver set.
  42. Step 44
    307 Break (3E) 2.0 HDI 110 2005 Wheel Bearing DIY replacement workshop manual
    Pull the bearing inner race out of the wheel hub. Use a bush and bearing driver set. Use a bearing separator.
  43. Step 45
    How to change Wheel Bearing on PEUGEOT 307 Break (3E) 2006 - tips and tricks
    Press out the wheel hub bearing. Use a bush and bearing driver set.
  44. Step 46
    Step-by-step recommendations for DIY replacement Peugeot 307 Estate 2007 2.0 HDI 110 Wheel Bearing
    Clean the hub bearing mounting seat. Use all-purpose cleaning spray. Use WD-40 spray.
  45. Step 47
    DIY replacement of Wheel Bearing on PEUGEOT 307 Break (3E) 1.6 HDi 2008 is not an issue anymore with our step-by-step tutorial
    Press the new bearing in the steering knuckle. Use a bush and bearing driver set.
    Replacement: wheel bearing – PEUGEOT 307 Break (3E). AUTODOC recommends:
    Check to make sure the wheel hub bearing is positioned correctly. Avoid its misalignment. Stop pressing on the surface of the bearing immediately after it has been fitted into its mounting seat.
  46. Step 48
    How to change Wheel Bearing on Peugeot 307 Estate 2002 - free PDF and video manuals
    Install the wheel hub bearing retaining ring. Use circlip pliers.
  47. Step 49
    How to replace PEUGEOT 307 Break (3E) 1.6 16V 2003 Wheel Bearing - step-by-step manuals and video guides
    Clean the hub. Use WD-40 spray.
  48. Step 50
    Peugeot 307 Estate 1.6 HDi 110 2004 Wheel Bearing replacement: free workshop manuals
    Install the wheel hub on the steering knuckle. Use a bush and bearing driver set.
    AUTODOC recommends:
    Make sure that the wheel hub is positioned correctly. Avoid any misalignment.
  49. Step 51
    Changing Wheel Bearing on PEUGEOT 307 Break (3E) 2.0 HDI 90 2005 by yourself
    Treat the ABS sensor fastener. Use all-purpose cleaning spray. Use a multipurpose grease.
  50. Step 52
    How to remove PEUGEOT 307 2.0 HDI 110 2006 Wheel Bearing - online easy-to-follow instructions
    Connect the ABS sensor.
  51. Step 53
    How to replace Wheel Bearing on PEUGEOT 307 Break (3E) 2007: download PDF manuals and video instructions
    Tighten the fastener that connects the ABS sensor to the steering knuckle. Use a drive socket #13. Use a torque wrench. Tighten it to 10 nm torque.
  52. Step 54
    How hard is it to do yourself: Wheel Bearing replacement on Peugeot 307 Estate 2.0 2008 - download illustrated guide
    Treat the shock strut mounting seat on the steering knuckle. Use a wire brush. Use WD-40 spray.
  53. Step 55
    Need to know how to renew Wheel Bearing on PEUGEOT 307 2009? This free workshop manual will help you to do it yourself
    Install the steering knuckle assembled with the wheel hub.
  54. Step 56
    Changing of Wheel Bearing on Peugeot 307 Estate 2002 won't be an issue if you follow this illustrated step-by-step guide
    Fix the shock absorber strut on the steering knuckle.
  55. Step 57
    PEUGEOT 307 2.0 HDi 135 Wheel Bearing replacement: online guides and video tutorials
    Prop up the steering knuckle. Use a hydraulic transmission jack.
  56. Step 58
    Replacing Wheel Bearing on Peugeot 307 Estate 2004 1.6 16V by yourself
    Install the fastening bolt.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Searching for the right tyres?

Find out which tyre and wheel sizes are compatible with the PEUGEOT 307 Estate (3E) model.

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
PEUGEOT 307 Break (3E) Wheel Bearing replace by yourself - Scan QR-code and download AUTODOC CLUB app
Scan

To download the app:

  • - scan the QR code
  • - download from App Store
  • - download from Google Play
Autodoc CLUB App icon
DIY PEUGEOT 307 Break (3E) Wheel Bearing replacement - online guide
Tips & tricks for your PEUGEOT 307 Break (3E)
View more
  • How to change Wheel bearings on PEUGEOT 307 Break (3E) 1.6 HDi - replacement tricks
    5 common car washing mistakes | AUTODOC tips
  • Changing Hub bearing Peugeot 307 Estate 1.6 16V - Replacement Tips
    How to start a car after a long idle period | AUTODOC tips
  • Maintenance Hacks - PEUGEOT 307 Break (3E) 1.6 HDi 110 Wheel bearing kit replacement guide
    How to remove rust | AUTODOC tips
  • Replace Wheel hub bearing on Peugeot 307 Estate - free video tips
    DIY valve cover restoration | AUTODOC tips