
Disclaimer
How to change rear wheel bearing on AUDI A4 Avant (8D5, B5) – replacement guide
downloads:
3
Views:
15
Important!
This replacement procedure can be used for:
AUDI A4 Avant (8D5, B5) 1.6, AUDI A4 Avant (8D5, B5) 1.8, AUDI A4 Avant (8D5, B5) 1.8 T, AUDI A4 Avant (8D5, B5) 2.6, AUDI A4 Avant (8D5, B5) 2.8, AUDI A4 Avant (8D5, B5) 1.9 TDI, AUDI A4 Avant (8D5, B5) 1.9 TDI, AUDI A4 Avant (8D5, B5) 2.8, AUDI A4 Avant (8D5, B5) 2.4, AUDI A4 Avant (8D5, B5) 2.5 TDI, AUDI A4 Avant (8D5, B5) 1.9 TDI, AUDI A4 Avant (8D5, B5) 1.8 T, AUDI A4 Avant (8D5, B5) 1.9 TDI, AUDI A4 Avant (8D5, B5) 1.8, AUDI A4 Avant (8D5, B5) 1.6, AUDI A4 Avant (8D5, B5) 2.4, AUDI A4 Avant (8D5, B5) 1.9 Hybrid, AUDI A4 Avant (8D5, B5) 2.8 … View more
The steps may slightly vary depending on the car design.
AUDI A4 Avant (8D5, B5) 1.6, AUDI A4 Avant (8D5, B5) 1.8, AUDI A4 Avant (8D5, B5) 1.8 T, AUDI A4 Avant (8D5, B5) 2.6, AUDI A4 Avant (8D5, B5) 2.8, AUDI A4 Avant (8D5, B5) 1.9 TDI, AUDI A4 Avant (8D5, B5) 1.9 TDI, AUDI A4 Avant (8D5, B5) 2.8, AUDI A4 Avant (8D5, B5) 2.4, AUDI A4 Avant (8D5, B5) 2.5 TDI, AUDI A4 Avant (8D5, B5) 1.9 TDI, AUDI A4 Avant (8D5, B5) 1.8 T, AUDI A4 Avant (8D5, B5) 1.9 TDI, AUDI A4 Avant (8D5, B5) 1.8, AUDI A4 Avant (8D5, B5) 1.6, AUDI A4 Avant (8D5, B5) 2.4, AUDI A4 Avant (8D5, B5) 1.9 Hybrid, AUDI A4 Avant (8D5, B5) 2.8 … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Wheel Bearing for A4 Avant (8D5, B5) and other AUDI models
Wheel bearing kit
Alternative products

Wire brush
WD-40 spray
All-purpose cleaning spray
Brake cleaner
Multipurpose grease
Copper grease
Torque wrench
Combination spanner #15
Drive socket # 13
Drive socket # 24
HEX bit No.H8
Wheel impact socket #17
Ratchet wrench
Bush and bearing driver set
Flat screwdriver
Rubber mallet
Tap wrench
Hammer
Hub slide hammer puller
Universal puller
Crow bar
Wheel chock
AUTODOC recommends:
- Do not re-use the bearing assembly of your AUDI A4 Avant (8D5, B5) car.
- The wheel hub bearing replacement procedure is identical for both wheels on the same axle.
- Please note: all work on the car – AUDI A4 Avant (8D5, B5) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1Secure the wheels with chocks.Step 2Loosen the wheel mounting bolts. Use wheel impact socket #17.
- Step 3Raise the rear of the car and secure on supports.Step 4Unscrew the wheel bolts.AUTODOC recommends:Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. AUDI A4 Avant (8D5, B5)
- Step 5Remove the wheel.
- Step 6Clean the brake caliper fasteners. Use a wire brush. Use WD-40 spray.
- Step 7Unscrew the brake caliper fastening. Use a combination spanner #15. Use a drive socket #13. Use a ratchet wrench.
- Step 8Remove the brake caliper. Use a crowbar.Replacement: wheel bearing – AUDI A4 Avant (8D5, B5). Professionals recommend:Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur.Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary.
- Step 9Remove the brake pads.
- Step 10Clean the brake caliper bracket fasteners. Use a wire brush. Use WD-40 spray.
- Step 11Unscrew the caliper bracket fastening. Use HEX No.H8. Use a ratchet wrench. Use a tap wrench.
- Step 12Remove the caliper bracket.
- Step 13Clean the brake disc fastener. Use a wire brush. Use WD-40 spray.
- Step 14Remove the wheel hub nut cap. Use a hammer. Use a crowbar.
- Step 15Remove the cotter pin securing the hub nut. Use a crowbar. Use a flat screwdriver.
- Step 16Unscrew the hub nut. Use a drive socket #24. Use a tap wrench.
- Step 17Remove the brake disc assemled with the wheel hub bearing. Use a crowbar.
- Step 18Clean the stub axle. Use a wire brush. Use all-purpose cleaning spray.
- Step 19Clean the hub bearing mounting seat. Use a wire brush. Use WD-40 spray.
- Step 20Press out the wheel hub bearing. Use a bush and bearing driver set. Use a hammer.
- Step 21Remove the bearing inner race from the wheel hub. Remove the inner oil seal of the wheel bearing. Use a universal puller. Use the hub slide hammer puller.
- Step 22Clean the hub bearing mounting seat. Use a wire brush. Use WD-40 spray.Step 23Press fit the new wheel hub bearing into the brake disc. Use a bush and bearing driver set. Use a hammer.Replacement: wheel bearing – AUDI A4 Avant (8D5, B5). Tip:Check to make sure the wheel hub bearing is positioned correctly. Avoid its misalignment. Stop pressing on the surface of the bearing immediately after it has been fitted into its mounting seat.
- Step 24Install the inner race of the wheel bearing into the hub. Use a bush and bearing driver set. Use a hammer.
- Step 25Treat the wheel hub bearing. Use a multipurpose grease.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the AUDI A4 B5 Avant (8D5) model
Popular maintenance tutorials for Audi A4 B5 Avant
Complete guides for changing the Wheel bearings on different AUDI A4 models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your AUDI A4 Avant (8D5, B5)
View more
- Revive Your Vehicle's Look | How to Restore Wheel Rims Yourself!
- Drive with Care: 8 Common Bad Driving Habits Explained | AUTODOC
- Top 7 signs of a bad starter
- The Ultimate Guide to Engine Bay Cleaning | AUTODOC
Most commonly replaced car parts on AUDI A4
Time to replace parts? Get even better deals in our Shop app.

SCAN ME