Disclaimer
How to change rear shock absorbers on VOLVO S80 I (184) – replacement guide
downloads:
6
Views:
67
Important!
This replacement procedure can be used for:
VOLVO S80 I (184) 2.9, VOLVO S80 I (184) T6, VOLVO S80 I (184) 2.4, VOLVO S80 I (184) 2.0 T, VOLVO S80 I (184) 2.5 TDI, VOLVO S80 I (184) 2.0, VOLVO S80 I (184) 2.4, VOLVO S80 I (184) 2.9, VOLVO S80 I (184) 2.0 T, VOLVO S80 I (184) 2.4 T, VOLVO S80 I (184) D5, VOLVO S80 I (184) 2.4 Bifuel (CNG), VOLVO S80 I (184) 3.0, VOLVO S80 I (184) T6, VOLVO S80 I (184) 2.4 D, VOLVO S80 I (184) 2.5 T AWD, VOLVO S80 I (184) 2.5 T, VOLVO S80 I (184) 2.3 R, VOLVO S80 I (184) 2.4 Bifuel (LPG) … View more
The steps may slightly vary depending on the car design.
VOLVO S80 I (184) 2.9, VOLVO S80 I (184) T6, VOLVO S80 I (184) 2.4, VOLVO S80 I (184) 2.0 T, VOLVO S80 I (184) 2.5 TDI, VOLVO S80 I (184) 2.0, VOLVO S80 I (184) 2.4, VOLVO S80 I (184) 2.9, VOLVO S80 I (184) 2.0 T, VOLVO S80 I (184) 2.4 T, VOLVO S80 I (184) D5, VOLVO S80 I (184) 2.4 Bifuel (CNG), VOLVO S80 I (184) 3.0, VOLVO S80 I (184) T6, VOLVO S80 I (184) 2.4 D, VOLVO S80 I (184) 2.5 T AWD, VOLVO S80 I (184) 2.5 T, VOLVO S80 I (184) 2.3 R, VOLVO S80 I (184) 2.4 Bifuel (LPG) … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Shock Absorber for S80 I (184) and other VOLVO models
Alternative products

Wire brush
WD-40 spray
Brake cleaner
Copper grease
Combination spanner #18
Torx bit T30
Impact socket №18
Wheel impact socket #19
Ratchet wrench
Torque wrench
Tap wrench
Locking pliers
Crow bar
Hydraulic transmission jack
Wheel chock
Replacement: shock absorbers – VOLVO S80 I (TS, XY). Professionals recommend:
- Both shock absorbers of the rear suspension should be replaced simultaneously.
- The replacement procedure is identical for the left and right shock absorbers of the rear suspension.
- All work should be done with the engine stopped.
Replacement: shock absorbers – VOLVO S80 I (TS, XY). Take the following steps:
- Step 1
Open the boot lid. - Step 2
Move the folding shelf and detach it from the retainers. By doing this, you will get access to the side trim plastic panels. - Step 3
Raise the lower lining of the boot. - Step 4
Remove the boot front lower lining. - Step 5
Clean the shock absorber fasteners. Use a wire brush. Use WD-40 spray. - Step 6
Loosen the upper fastener of the shock absorber. Use a combination spanner #18. Use Torx T30. Use a ratchet wrench. - Step 7
Secure the wheels with chocks. - Step 8
Loosen the wheel mounting bolts. Use wheel impact socket #19. - Step 9Raise the rear of the car and secure on supports.Step 10
Unscrew the wheel bolts.Replacement: shock absorbers – VOLVO S80 I (TS, XY). AUTODOC recommends:To avoid injury, hold up the wheel when unscrewing the bolts. - Step 11
Remove the wheel. - Step 12
Support the arm. Use a hydraulic transmission jack. - Step 13
Clean the shock absorber fasteners. Use a wire brush. Use WD-40 spray. - Step 14
Unscrew the lower fastener of the shock absorber. Use a drive socket #18. Use a tap wrench. - Step 15
Unscrew the upper fastener of the shock absorber.AUTODOC recommends:Important! Hold the shock absorber while unscrewing the fastening bolts. VOLVO S80 I (TS, XY) - Step 16
Remove the fastening bolt. - Step 17
Remove the shock absorber. Use a crowbar.Replacement: shock absorbers – VOLVO S80 I (TS, XY). Tip from AUTODOC experts:Before installing a new shock absorber you should pump it manually 3-5 times. - Step 18
Clean the shock absorber mounting seats. Use a wire brush. Use WD-40 spray. - Step 19
Place the shock absorber in the wheel arch and fasten it.Replacement: shock absorbers – VOLVO S80 I (TS, XY). Tip from AUTODOC:To avoid injury, hold the shock absorber cautiously tight when screwing in the fastening bolts. - Step 20
Install the fastening bolt. - Step 21
Screw in the lower fastener of the shock absorber. Use a drive socket #18. - Step 22
Tighten the top shock absorber fastening. Use a combination spanner #18. Use a drive socket #18. Use locking pliers. Use a torque wrench. Tighten it to 60 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the VOLVO S80 I (TS, 184) model
Popular maintenance tutorials for Volvo S80 1
Complete guides for changing the Shock absorbers on different VOLVO S80 models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your VOLVO S80 I (184)
View more
Understanding Car Tools: The Key Differences You Need to Know | AUTODOC tips
Top 7 signs of a bad starter
Unveiling the secrets: Detecting vacuum leaks with a Smoke Machine | AUTODOC
3 essential tips for choosing summer tyres | Get ready for warmer weather
Most commonly replaced car parts on VOLVO S80
ОЕ number
Time to replace parts? Get even better deals in our Shop app.

SCAN ME




























