Disclaimer
How to change rear shock absorbers on Audi A4 B6 – replacement guide
downloads:
2
Views:
86
Important!
This replacement procedure can be used for:
AUDI A4 Saloon (8E2, B6) 1.8 T quattro, AUDI A4 Saloon (8E2, B6) 1.8 T, AUDI A4 Saloon (8E2, B6) 2.0, AUDI A4 Saloon (8E2, B6) 1.8 T quattro, AUDI A4 Saloon (8E2, B6) 3.0, AUDI A4 Saloon (8E2, B6) 3.0 quattro, AUDI A4 Saloon (8E2, B6) 1.9 TDI, AUDI A4 Saloon (8E2, B6) 2.5 TDI quattro, AUDI A4 Saloon (8E2, B6) 1.6, AUDI A4 Saloon (8E2, B6) 2.5 TDI, AUDI A4 Saloon (8E2, B6) 1.9 TDI, AUDI A4 Saloon (8E2, B6) 2.4, AUDI A4 Saloon (8E2, B6) 2.0 FSI, AUDI A4 Saloon (8E2, B6) 1.9 TDI quattro, AUDI A4 Saloon (8E2, B6) 2.5 TDI, AUDI A4 Saloon (8E2, B6) 2.4, AUDI A4 Saloon (8E2, B6) 1.8 T, AUDI A4 Saloon (8E2, B6) 1.8 T quattro, AUDI A4 Saloon (8E2, B6) 1.9 TDI, AUDI A4 Saloon (8E2, B6) 1.8 T quattro, AUDI A4 Saloon (8E2, B6) 3.0, AUDI A4 Saloon (8E2, B6) 3.0 quattro … View more
The steps may slightly vary depending on the car design.
AUDI A4 Saloon (8E2, B6) 1.8 T quattro, AUDI A4 Saloon (8E2, B6) 1.8 T, AUDI A4 Saloon (8E2, B6) 2.0, AUDI A4 Saloon (8E2, B6) 1.8 T quattro, AUDI A4 Saloon (8E2, B6) 3.0, AUDI A4 Saloon (8E2, B6) 3.0 quattro, AUDI A4 Saloon (8E2, B6) 1.9 TDI, AUDI A4 Saloon (8E2, B6) 2.5 TDI quattro, AUDI A4 Saloon (8E2, B6) 1.6, AUDI A4 Saloon (8E2, B6) 2.5 TDI, AUDI A4 Saloon (8E2, B6) 1.9 TDI, AUDI A4 Saloon (8E2, B6) 2.4, AUDI A4 Saloon (8E2, B6) 2.0 FSI, AUDI A4 Saloon (8E2, B6) 1.9 TDI quattro, AUDI A4 Saloon (8E2, B6) 2.5 TDI, AUDI A4 Saloon (8E2, B6) 2.4, AUDI A4 Saloon (8E2, B6) 1.8 T, AUDI A4 Saloon (8E2, B6) 1.8 T quattro, AUDI A4 Saloon (8E2, B6) 1.9 TDI, AUDI A4 Saloon (8E2, B6) 1.8 T quattro, AUDI A4 Saloon (8E2, B6) 3.0, AUDI A4 Saloon (8E2, B6) 3.0 quattro … View more
The steps may slightly vary depending on the car design.
How to change rear shock absorbers on AUDI A4 B6 TUTORIAL | AUTODOC

All the parts you need to replace – Shock Absorber for A4 Saloon (8E2, B6) and other AUDI models
Alternative products

Wire brush
WD-40 spray
Brake cleaner
Copper grease
Combination spanner #16
Combination spanner #21
Drive socket # 16
Drive socket # 21
Torx bit T25
HEX bit No.H6.
Wheel impact socket #17
Ratchet wrench
Torque wrench
Adjustable wrench
Hammer
Pin punch
Hydraulic transmission jack
Wheel chock
Replacement: shock absorbers – Audi A4 B6. Tip from AUTODOC:
- Both shock absorbers of the rear suspension should be replaced simultaneously.
- The replacement procedure is identical for the left and right shock absorbers of the rear suspension.
- Please note: all work on the car – Audi A4 B6 – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1
Secure the wheels with chocks. - Step 2Loosen the wheel mounting bolts. Use wheel impact socket #17.Step 3
Raise the rear of the car and secure on supports. - Step 4
Unscrew the wheel bolts.AUTODOC recommends:Important! Hold the wheel while unscrewing the fastening bolts. Audi A4 B6 - Step 5
Remove the wheel. - Step 6Clean the shock absorber fasteners. Use a wire brush. Use WD-40 spray.Step 7
Unscrew the lower fastener of the shock absorber. Use a combination spanner #21. Use a drive socket #21. Use a ratchet wrench. - Step 8
Support the arm. Use a hydraulic transmission jack. - Step 9Detach the lower part of the shock absorber. Use a pin punch. Use a hammer.Step 10
Unscrew and remove the wheel arch cover fasteners. Use Torx T25. Use a ratchet wrench. - Step 11
Remove the wheel arch cover. - Step 12
Unscrew the upper fastener of the shock absorber. Use HEX No.H6. Use a ratchet wrench.AUTODOC recommends:Audi A4 B6 – To avoid injury, hold the shock absorber while unscrewing the fastening bolts. - Step 13
Remove the shock absorber. - Step 14Clean the shock absorber rod fastener. Use a wire brush. Use WD-40 spray.Step 15
Remove the shock absorber piston rod fastening. Use a drive socket #16. Use a ratchet wrench. - Step 16
Remove the top mount. - Step 17
Remove the shock absorber dust cap and the bump stop.Replacement: shock absorbers – Audi A4 B6. AUTODOC recommends:Τhoroughly examine the shock absorber mount, dust boot, bump stop. Replace them if necessary.Before installing a new shock absorber you should pump it manually 3-5 times. - Step 18
Install the mount, boot and bump stop onto a new shock absorber. - Step 19
Screw the shock strut piston rod upper fastening. Use a combination spanner #16. Use an adjustable wrench. Use a torque wrench. Tighten it to 25 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the AUDI A4 B6 Saloon (8E2) model
Popular maintenance tutorials for Audi A4 B6
Complete guides for changing the Shock absorbers on different AUDI A4 models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your AUDI A4 Saloon (8E2, B6)
View more
Regain Your Confidence on the Road: Easy Headlight Restoration Tips
Top 4 Car Cleaning Products to Protect Your Car's Body | AUTODOC Tips
Unveiling the secrets: Detecting vacuum leaks with a Smoke Machine | AUTODOC
Revive Your Vehicle's Look | How to Restore Wheel Rims Yourself!
Most commonly replaced car parts on AUDI A4
Time to replace parts? Get even better deals in our Shop app.

SCAN ME






























