Disclaimer
How to change rear brake shoes on VW DERBY (86) – replacement guide
downloads:
3
Views:
15
Recommended replacement interval for the part category Brake Shoe Set : 100000 km
Important!
This replacement procedure can be used for:
VW DERBY (86) 1.3, VW DERBY (86) 1.3, VW DERBY (86) 1.1, VW DERBY (86) 0.9 … View more
The steps may slightly vary depending on the car design.
VW DERBY (86) 1.3, VW DERBY (86) 1.3, VW DERBY (86) 1.1, VW DERBY (86) 0.9 … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Brake Shoes for DERBY (86) and other VW models
Alternative products

WD-40 spray
All-purpose cleaning spray
Copper grease
Torque wrench
Drive socket # 30
Wheel impact socket #17
Ratchet wrench
Brake shoe retaining spring compressor
Flat screwdriver
Hammer
Pliers
Round-nose pliers
Water pump pliers
Crow bar
Rubber mallet
Wheel chock
Replacement: brake shoes – VW DERBY (86). AUTODOC recommends:
- Replace brake shoes as a set on an axle. This will ensure efficient braking.
- The replacement procedure is identical for brake shoes on the same axle.
- Please note: all work on the car – VW DERBY (86) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1Open the bonnet. Unscrew the brake fluid reservoir cap.Step 2Secure the wheels with chocks.Step 3
Loosen the wheel mounting bolts. Use wheel impact socket #17. - Step 4Raise the rear of the car and secure on supports.Step 5
Unscrew the wheel bolts.AUTODOC recommends:Important! Hold the wheel while unscrewing the fastening bolts. VW DERBY (86) - Step 6
Remove the wheel. - Step 7
Remove the wheel hub nut cap. Use a crowbar. Use a hammer. - Step 8
Remove the cotter pin securing the hub nut. Use a crowbar. Use a flat screwdriver. - Step 9
Unscrew the hub nut. Use a drive socket #30. Use a ratchet wrench. - Step 10
Remove the brake drum assembled with the wheel hub bearing. - Step 11
Clean the hub bearing mounting seat. Clean the hub. Use all-purpose cleaning spray. - Step 12
Remove the hold-down spring. Use round-nose pliers. - Step 13
Remove the upper return spring of the brake shoes. Use round-nose pliers. - Step 14
Remove the brake shoe hold-down cup. Use a brake shoe retaining spring compressor. - Step 15
Compress the wheel cylinder. Use water pump pliers. - Step 16
Remove both shoes from the mounting bracket. Use a crowbar.Replacement: brake shoes – VW DERBY (86). Tip from AUTODOC experts:Don't press the brake pedal after removing the rear brake drum shoes. This will cause the piston to fall out of the brake cylinder, leakage of brake fluid and depressurization of the system. - Step 17
Remove the lower return spring of the brake shoes. - Step 18
Disconnect the parking brake cable. Use a crowbar. - Step 19Remove the brake shoe adjuster lever.Step 20
Connect the parking brake cable to the parking brake lever. Use round-nose pliers. - Step 21
Install the brake shoe adjuster lever. - Step 22
Install the brake shoes on the working brake cylinder on the bracket and on the brake-support plate bracket.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the VW Derby I (86) model
Popular maintenance tutorials for VW Derby 86
Complete guides for changing the Brake shoe set on different VW DERBY models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your VW DERBY (86)
View more
5 more brake repair mistakes | Stop making these brake repair mistakes
What to do if your check engine light is on | AUTODOC tips
How to get your motorcycle ready for spring
Top 5 possible reasons your car is shaking or vibrating
Most commonly replaced car parts on VW DERBY
Time to replace parts? Get even better deals in our Shop app.

SCAN ME
































