
Disclaimer
How to change rear brake discs on MERCEDES-BENZ VITO Box (638) – replacement guide
downloads:
4
Views:
136

Recommended replacement interval for the part category Brake disc : 50000 km
Important!
This replacement procedure can be used for:
MERCEDES-BENZ VITO Box (638) 108 D 2.3 (638.064, 638.068), MERCEDES-BENZ VITO Box (638) 110 D 2.3 (638.074, 638.078), MERCEDES-BENZ VITO Box (638) 113 2.0 (638.014, 638.094), MERCEDES-BENZ VITO Box (638) 114 2.3 (638.034, 638.094), MERCEDES-BENZ VITO Box (638) 108 CDI 2.2 (638.094), MERCEDES-BENZ VITO Box (638) 110 CDI 2.2 (638.094), MERCEDES-BENZ VITO Box (638) 112 CDI 2.2 (638.094) … View more
The steps may slightly vary depending on the car design.
MERCEDES-BENZ VITO Box (638) 108 D 2.3 (638.064, 638.068), MERCEDES-BENZ VITO Box (638) 110 D 2.3 (638.074, 638.078), MERCEDES-BENZ VITO Box (638) 113 2.0 (638.014, 638.094), MERCEDES-BENZ VITO Box (638) 114 2.3 (638.034, 638.094), MERCEDES-BENZ VITO Box (638) 108 CDI 2.2 (638.094), MERCEDES-BENZ VITO Box (638) 110 CDI 2.2 (638.094), MERCEDES-BENZ VITO Box (638) 112 CDI 2.2 (638.094) … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Brake Discs for VITO Box (638) and other MERCEDES-BENZ models
Brake disc
Alternative products

Wire brush
WD-40 spray
Brake cleaner
Anti-squeal paste
Copper grease
Drive socket # 13
Drive socket # 16
Wheel impact socket #17
Brake caliper wind back tool
Ratchet wrench
Torque wrench
Phillips screwdriver
Impact screwdriver
Rubber mallet
Crow bar
Wheel chock
Replacement: brake discs – MERCEDES-BENZ VITO Box (638). AUTODOC recommends:
- Replace the brake disks on the car MERCEDES-BENZ VITO Box (638) in complete set for each axis. Regardless of the state of components. This will ensure even braking.
- The replacement procedure is identical for both brake disks on the same axle.
- When changing the brake discs, always replace the brake pads.
- All work should be done with the engine stopped.
Replacement: brake discs – MERCEDES-BENZ VITO Box (638). Take the following steps:
- Step 1Open the bonnet. Unscrew the brake fluid reservoir cap.Step 2Secure the wheels with chocks.
- Step 3Loosen the wheel mounting bolts. Use wheel impact socket #17.
- Step 4Raise the rear of the car and secure on supports.Step 5Unscrew the wheel bolts.Replacement: brake discs – MERCEDES-BENZ VITO Box (638). Professionals recommend:To avoid injury, hold up the wheel when unscrewing the bolts.
- Step 6Remove the wheel.
- Step 7Clean the brake pads fasteners. Use a wire brush. Use WD-40 spray.
- Step 8Remove the retaining springs of the brake pads. Use a crowbar.
- Step 9Remove the brake pad retaining pin.
- Step 10Remove the retainer of the brake pads. Use a crowbar. Use a rubber mallet.
- Step 11Remove the brake pads. Use a crowbar.
- Step 12Clean the brake caliper fasteners. Use a wire brush. Use WD-40 spray.
- Step 13Unscrew the brake caliper fastening. Use a drive socket #13. Use a drive socket #16. Use a ratchet wrench.
- Step 14Remove the brake caliper.Replacement: brake discs – MERCEDES-BENZ VITO Box (638). Tip:Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur.
- Step 15Unscrew the brake disc fastening. Use a Phillips screwdriver. Use an impact screwdriver.Replacement: brake discs – MERCEDES-BENZ VITO Box (638). AUTODOC experts recommend:If necessary, use a rubber mallet.
- Step 16Remove the brake disc.
- Step 17Clean the hub. Use a wire brush. Treat the contacting surface. Use copper grease.
- Step 18Install the brake disc.
- Step 19Tighten the brake disc fastening. Use a Phillips screwdriver. Use a torque wrench. Tighten it to 9 Nm torque.
- Step 20Treat the brake caliper piston. Use a brake cleaner.AUTODOC recommends:Replacement: brake discs – MERCEDES-BENZ VITO Box (638). After applying the spray, wait a few minutes.
- Step 21Press in the brake caliper piston. Use brake caliper wind back tool.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the MERCEDES-BENZ Vito Van (W638) model
Popular maintenance tutorials for Mercedes Vito W638
Complete guides for changing the Brake rotors on different MERCEDES-BENZ VITO models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your MERCEDES-BENZ VITO Box (638)
View more
- DIY starter repair | AUTODOC tips
- Easy Steps to Fix Minor Scratches on Your Vehicle | AUTODOC tips
- Transform Your Engine Bay: Affordable Valve Cover Restoration with AUTODOC
- Transform Your Car's Look: 6 Simple Accessories You Need to Try!
Most commonly replaced car parts on MERCEDES-BENZ VITO
Time to replace parts? Get even better deals in our Shop app.

SCAN ME