
Disclaimer
How to change rear anti roll bar links on VW PASSAT Variant (3B5) – replacement guide
downloads:
1
Views:
19
Important!
This replacement procedure can be used for:
VW PASSAT Variant (3B5) 2.8 V6 Syncro/4motion, VW PASSAT Variant (3B5) 1.8 Syncro/4motion, VW PASSAT Variant (3B5) 1.9 TDI Syncro/4motion, VW PASSAT Variant (3B5) 2.3 VR5 Syncro/4motion, VW PASSAT Variant (3B5) 2.5 TDI Syncro/4motion, VW PASSAT Variant (3B5) 1.9 TDI 4motion, VW PASSAT Variant (3B5) 2.0 4motion … View more
The steps may slightly vary depending on the car design.
VW PASSAT Variant (3B5) 2.8 V6 Syncro/4motion, VW PASSAT Variant (3B5) 1.8 Syncro/4motion, VW PASSAT Variant (3B5) 1.9 TDI Syncro/4motion, VW PASSAT Variant (3B5) 2.3 VR5 Syncro/4motion, VW PASSAT Variant (3B5) 2.5 TDI Syncro/4motion, VW PASSAT Variant (3B5) 1.9 TDI 4motion, VW PASSAT Variant (3B5) 2.0 4motion … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Anti Roll Bar Links for PASSAT Variant (3B5) and other VW models
Anti-roll bar link
Alternative products

Wire brush
WD-40 spray
Brake cleaner
Copper grease
Combination spanner #15
Drive socket # 15
Wheel impact socket #17
Ratchet wrench
Torque wrench
Hydraulic transmission jack
Wheel chock
AUTODOC recommends:
- Replace the stabiliser links on VW PASSAT Variant (3B5) in pairs.
- The replacement procedure is identical for both stabiliser links on the same axle.
- All work should be done with the engine stopped.
Replacement: anti roll bar links – VW PASSAT Variant (3B5). Use the following procedure:
- Step 1Secure the wheels with chocks.
- Step 2Loosen the wheel mounting bolts. Use wheel impact socket #17.
- Step 3Raise the rear of the car and secure on supports.Step 4Unscrew the wheel bolts.AUTODOC recommends:Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. VW PASSAT Variant (3B5)
- Step 5Remove the wheel.
- Step 6Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray.
- Step 7Unscrew the fastener connecting the stabilizer link to the control arm. Use a drive socket #15.
- Step 8Clean the fasteners of the stabilizer bush brackets. Use a wire brush. Use WD-40 spray.
- Step 9Unscrew the fasteners of the stabilizer bush brackets. Use a combination spanner #15. Use a drive socket #15.
- Step 10Unscrew the fasteners connecting the stabiliser link to the stabiliser bar. Use a combination spanner #15. Use a drive socket #15. Use a ratchet wrench.
- Step 11Remove the stabilizer rod.Replacement: anti roll bar links – VW PASSAT Variant (3B5). AUTODOC experts recommend:Examine stabiliser bushes. Replace them if needed.
- Step 12Install a new rod, tighten the fasteners. Use a combination spanner #15.
- Step 13Screw the fasteners of the stabilizer bush brackets. Use a combination spanner #15. Use a drive socket #15. Use a torque wrench. Tighten it to 35 Nm torque.
- Step 14Support the arm. Use a hydraulic transmission jack.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the VW Passat B5 Estate (3B5) model
Popular maintenance tutorials for Passat 3b5
Complete guides for changing the Drop links on different VW PASSAT models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your VW PASSAT Variant (3B5)
View more
- TOP 5 mistakes during DIY oil change | AUTODOC tips
- DIY starter repair | AUTODOC tips
- Petrol or diesel: The engine showdown! | AUTODOC
- How to Install a New Windscreen Yourself | AUTODOC Expert Tips
Most commonly replaced car parts on VW PASSAT
Time to replace parts? Get even better deals in our Shop app.

SCAN ME