Disclaimer
How to change mass air flow sensor on VW Transporter IV Platform / Chassis (70E, 70L, 70M, 7DE, 7DL) – replacement guide
downloads:
2
Views:
16
Important!
This replacement procedure can be used for:
VW Transporter IV Platform / Chassis (70E, 70L, 70M, 7DE, 7DL) 2.5, VW Transporter IV Platform / Chassis (70E, 70L, 70M, 7DE, 7DL) 2.5 Syncro … View more
The steps may slightly vary depending on the car design.
VW Transporter IV Platform / Chassis (70E, 70L, 70M, 7DE, 7DL) 2.5, VW Transporter IV Platform / Chassis (70E, 70L, 70M, 7DE, 7DL) 2.5 Syncro … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Mass Air Flow Sensor for Transporter IV Platform / Chassis (70E, 70L, 70M, 7DE, 7DL) and other VW models
Electronic spray
Torque wrench
Drive socket # 7
Drive socket # 10
Ratchet wrench
Phillips screwdriver
Fender cover
Replacement: mass air flow sensor – VW TRANSPORTER IV Platform/Chassis (70XD). AUTODOC recommends:
- Сlear the trouble codes from the electronic control unit if necessary.
- Make sure that no dust or dirt gets into the air duct components and the throttle body.
- Please note: all work on the car – VW TRANSPORTER IV Platform/Chassis (70XD) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1Open the bonnet.Step 2Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.Step 3
Detach the air duct housing from the air filter housing. - Step 4
Unscrew the fasteners of the heat shield of the air filter housing. Use a Phillips screwdriver. - Step 5
Remove the heat shield of the air filter housing. - Step 6
Detach the mass air flow sensor connector. - Step 7
Loosen the fastening clamp connecting the air duct to the air filter housing. Use a drive socket #7. Use a ratchet wrench. - Step 8
Unscrew the MAF sensor fasteners. Use a drive socket #10. Use a ratchet wrench. - Step 9
Remove the mass air flow sensor. - Step 10
Install a new mass air flow sensor. - Step 11
Tighten the MAF sensor fasteners. Use a drive socket #10. Use a torque wrench. Tighten it to 4 Nm torque. - Step 12
Screw the fastening clamp connecting the air duct to the air filter housing. Use a drive socket #7. Use a ratchet wrench.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Searching for the right tyres?
Find out which tyre and wheel sizes are compatible with the VW Transporter T4 Platform / Chassis (70E, 70L, 70M, 7DE, 7DL, 7D) model.
Popular maintenance tutorials for VW T4 Platform
Complete guides for changing the MAF sensor on different VW TRANSPORTER models
Free download PDF
972.8 KB
Free download PDF860.16 KB
Free download PDF972.8 KB
Free download PDF972.8 KB
Free download PDF972.8 KB
Your profile is your personal assistant.
It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents
Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
Scan
To download the app:
- - scan the QR code
- - download from App Store
- - download from Google Play
Tips & tricks for your VW Transporter IV Platform / Chassis (70E, 70L, 70M, 7DE, 7DL)
View more
How to polish an old engine valve cover to a shiny finish | AUTODOC Tips
How to paint a brake caliper | AUTODOC tips
How to check your head gasket | AUTODOC
What to do if your car's air conditioning isn't working properly | AUTODOC tips
