
Disclaimer
How to change ignition coil on VW PASSAT Variant (3B6) – replacement guide
downloads:
6
Views:
70
Important!
This replacement procedure can be used for:
VW PASSAT Variant (3B6) 2.0 4motion, VW PASSAT Variant (3B6) 2.0, VW PASSAT Variant (3B6) 1.6 … View more
The steps may slightly vary depending on the car design.
VW PASSAT Variant (3B6) 2.0 4motion, VW PASSAT Variant (3B6) 2.0, VW PASSAT Variant (3B6) 1.6 … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Ignition Coil for PASSAT Variant (3B6) and other VW models
Ignition coil
Alternative products

Electronic spray
Torque wrench
Combination spanner #10
Drive socket # 13
HEX bit No.H5
HEX bit No.H6
Ratchet wrench
Microfibre towel
Fender cover
Replacement: ignition coil – VW PASSAT Variant (3B6). Tip from AUTODOC experts:
- The replacement procedure is the same for the ignition coils of all cylinders.
- All work should be done with the engine stopped.
Replacement: ignition coil – VW PASSAT Variant (3B6). Recommended sequence of steps:
- Step 1Open the bonnet.Step 2Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.Step 3Disconnect the secondary air pump hoses.
- Step 4Cover the secondary air pump channels with a microfibre cloth to prevent dust and dirt from getting inside.
- Step 5Detach the secondary air pump connector.
- Step 6Unscrew the fasteners connecting the secondary air pump to its bracket. Use a combination spanner #10.
- Step 7Remove the secondary air pump.
- Step 8Unscrew the fastener of the secondary air pump bracket. Use HEX No.H6. Use a drive socket #13. Use a ratchet wrench.
- Step 9Remove the secondary air pump bracket.
- Step 10Detach the connector from the ignition coil.
- Step 11Disconnect the spark plug wires from the ignition coil.Replacement: ignition coil – VW PASSAT Variant (3B6). Tip:Remember the sequence of the spark plug wires connectors.
- Step 12Unscrew the ignition coil bracket. Use HEX No.H5. Use a ratchet wrench.
- Step 13Remove the ignition coil.
- Step 14Treat the ignition coil connector with electronic spray. The spray will protect the electrical contacts from corrosion, oxidation, and will reduce the contact resistance.
- Step 15Treat the spark plug wire connectors. Use electronic spray.
- Step 16Install the new ignition coil to the spark plug well. Make sure you hear a click indicating that it is locked in place.
- Step 17Tighten the ignition coil fastening. Use HEX No.H5. Use a torque wrench. Tighten it to 7 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the VW Passat B5 GP Estate (3BG, 3B6) model
Popular maintenance tutorials for Passat 3B6
Complete guides for changing the Coil pack on different VW PASSAT models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your VW PASSAT Variant (3B6)
View more
- How to remove rust | AUTODOC tips
- How to Make a DIY Foam Sprayer | AUTODOC tips
- How to unlock your car without a key | AUTODOC tips
- DIY manual gearbox restoration | Drivetrain restoration – Part 3
Most commonly replaced car parts on VW PASSAT
Time to replace parts? Get even better deals in our Shop app.

SCAN ME