Important!

This replacement procedure can be used for:
BMW X1 (E84) xDrive25i, BMW X1 (E84) sDrive18i, BMW X1 (E84) xDrive28i … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Ignition Coil for X1 (E84) and other BMW models

Alternative products

Ignition coil

Replacement: ignition coil – BMW X1 (E84). Tools you might need:

                      Electronic spray
                    
                      High-temperature anti-seize lubricant
                    
                      HEX bit no.H5.
                    
                      Drive socket # 8 
                    
                      Ratchet wrench
                    
                      Flat Screwdriver
                    
                      Fender cover

Buy tools

Replacement: ignition coil – BMW X1 (E84). AUTODOC recommends:

The replacement procedure is the same for the ignition coils of all cylinders.
All work should be done with the engine stopped.

Replacement: ignition coil – BMW X1 (E84). Take the following steps:

Step 1

Open the hood.

Step 2

Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.

Step 3

Unscrew the fasteners of the cabin filter housing cover. Use a drive socket #8. Use a ratchet wrench.
Step 4

Remove the cabin filter housing cover.

AUTODOC recommends:
Replacement: ignition coil – BMW X1 (E84). Do not use excessive force when removing the part as this may damage it.
Step 5

Remove the wiper arm covers.
Step 6

Detach the connectors from the climate control sensors.
Step 7

Remove the climate control sensors.

Step 8

Unscrew the fasteners of the lower part of the scuttle panel. Use a drive socket #8. Use a ratchet wrench.
Step 9

Detach the cable duct from the upper part of the microfilter housing. Use a flat screwdriver.
Step 10

Remove the lower part of the scuttle panel.
Step 11

Unscrew the engine cover fastener. Use HEX No.H5. Use a ratchet wrench.
Step 12

Remove the engine cover.

Replacement: ignition coil – BMW X1 (E84). Tip:
Do not apply excessive force when removing the part. Otherwise you may damage it.
Step 13

Detach the connector from the ignition coil.
Step 14

Treat the ignition coil connector with electronic spray. The spray will protect the electrical contacts from corrosion, oxidation, and will reduce the contact resistance.
Step 15

Take out the ignition coil from the spark plug well.
Step 16

Treat the ignition coil tips. Use high-temperature grease. Use a flat screwdriver.
Step 17

Install the new ignition coil to the spark plug well. Make sure you hear a click indicating that it is locked in place.
Step 18

Plug in the ignition coil connector.
Step 19

Install the engine cover and secure it.

Replacement: ignition coil – BMW X1 (E84). AUTODOC experts recommend:
Make sure the engine cover is properly seated. It should not be displaced with respect to the guiding fasteners.Do not apply excessive force when installing the part. Otherwise you may damage the fasteners.
Step 20

Screw in the engine cover fasteners. Use HEX No.H5. Use a ratchet wrench.
Step 21

Reinstall the lower part of the scuttle panel.
Step 22

Screw in the fasteners of the lower part of the scuttle panel. Use a drive socket #8. Use a ratchet wrench.
Step 23

Install the climate control sensors.
Step 24

Attach the connectors of the climate control sensors.
Step 25

Install the wiper arm covers.
Step 26

Attach the cable duct to the upper part of the microfilter housing.
Step 27

Reinstall the cabin filter housing cover. Make sure you hear a click indicating that it is locked in place.

AUTODOC recommends:
Warning! To avoid damaging the fasteners of the car during installation, do not use excessive force. BMW X1 (E84)
Step 28

Screw in the fasteners of the cabin filter housing cover. Use a drive socket #8. Use a ratchet wrench.

Step 29

Remove the fender protection cover.

Step 30

Close the hood.

Step 31

Run the engine for a few minutes. This is necessary in order to make sure that the component operates properly.

Step 32

Shut off the engine.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the BMW X1 (E84) model

BMW X1 E84 tyre size

How to change spark plugs on BMW X1 (E84) – replacement guide

Free download PDF
2.4 MB
How to change front brake pads on BMW X1 (E84) – replacement guide

Free download PDF
1.82 MB
How to change rear brake pads on BMW X1 (E84) – replacement guide

Free download PDF
1.53 MB
How to change front brake discs on BMW X1 (E84) – replacement guide

Free download PDF
2.08 MB
How to change rear brake discs on BMW X1 (E84) – replacement guide

Free download PDF
2.18 MB
How to change front wheel bearing on BMW X1 (E84) – replacement guide

Free download PDF
1.66 MB

How to change ignition coil on a car – replacement tutorial

Universal

Free download PDF
1.98 MB
How to change ignition coil on BMW E82 – replacement guide

Free download PDF
1.99 MB
How to change ignition coil on BMW 1 Hatchback (E87) – replacement guide

Free download PDF
1.72 MB
How to change ignition coil on BMW 5 Saloon (F10) – replacement guide

Free download PDF
1.74 MB
How to change ignition coil on BMW 3 Saloon (E90) – replacement guide

Free download PDF
1.73 MB
How to change ignition coil on BMW X3 (F25) – replacement guide

Free download PDF
1.72 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

Understanding Car Tools: The Key Differences You Need to Know | AUTODOC tips

8K views

Published on: 16/12/2021
Kolbenschmidt plastic gauge overview

2K views

Published on: 23/04/2025
#DIY Guide: How to Fix a Cracked Windscreen Without a Garage Visit

8K views

Published on: 14/12/2023
How to Order Car Parts Online: Avoid These 5 Common Pitfalls

4K views

Published on: 10/03/2022