Important!
This replacement procedure can be used for:
NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 1.6 dCi Allrad, NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 1.6 dCi, NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 1.5 dCi, NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 2.0 Allrad, NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 2.0, NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 1.6 CVTC View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

Tools
Replacement: wheel bearing – NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E). List of the tools you'll need:
Wire brush
WD-40 spray
Brake cleaner
Multipurpose grease
Copper grease
Torque wrench
Combination spanner #18
Drive socket # 10
Drive socket # 17
Drive socket # 18
Drive socket # 19
Drive socket # 21
Drive socket # 32
Wheel impact socket #21
Ratchet wrench
Tap wrench
Hammer
Pin punch
Clip removal tool
Vice
Water pump pliers
Flat Screwdriver
Crow bar
Wheel chock
Replacement: wheel bearing – NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E). Professionals recommend:
  • Do not re-use the bearing assembly of your NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) car.
  • The wheel hub bearing replacement procedure is identical for both wheels on the same axle.
  • Please note: all work on the car – NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) – should be done with the engine switched off.
Carry out replacement in the following order:
  1. Step 1
    How to change Wheel Bearing on NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 2006 - free PDF and video manuals
    Secure the wheels with chocks.
  2. Step 2
    How to replace NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 1.6 CVTC 2007 Wheel Bearing - step-by-step manuals and video guides
    Loosen the wheel mounting bolts. Use wheel impact socket #21.
  3. Step 3
    Raise the front of the car and secure on supports.
    Step 4
    NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 2.0 2008 Wheel Bearing replacement: free workshop manuals
    Unscrew the wheel bolts.
    Replacement: wheel bearing – NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E). AUTODOC recommends:
    To avoid injury, hold up the wheel when unscrewing the bolts.
  4. Step 5
    Changing Wheel Bearing on NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 1.5 dCi 2009 by yourself
    Remove the wheel.
  5. Step 6
    How to remove NISSAN QASHQAI 1.6 dCi 2010 Wheel Bearing - online easy-to-follow instructions
    Clean the fastener of the driveshaft. Use a wire brush. Use WD-40 spray.
  6. Step 7
    How to replace Wheel Bearing on NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 2011: download PDF manuals and video instructions
    Remove the CV axle nut cotter pin. Use a crowbar.
  7. Step 8
    How hard is it to do yourself: Wheel Bearing replacement on NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 2.0 dCi Allrad 2012 - download illustrated guide
    Loosen the fastener of the driveshaft. Use a drive socket #32. Use a ratchet wrench.
  8. Step 9
    Need to know how to renew Wheel Bearing on NISSAN QASHQAI 2013? This free workshop manual will help you to do it yourself
    Spread the brake pads. Use a crowbar.
  9. Step 10
    Changing of Wheel Bearing on NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 2014 won't be an issue if you follow this illustrated step-by-step guide
    Unscrew the end fastening nut to the steering knuckle. Use a drive socket #17. Use a ratchet wrench.
  10. Step 11
    NISSAN QASHQAI 2.0 Wheel Bearing replacement: online guides and video tutorials
    Disconnect the tie rod end from the steering knuckle.
  11. Step 12
    Replacing Wheel Bearing on NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 2007 1.6 CVTC by yourself
    Unscrew the caliper bracket fastening. Use a drive socket #19. Use a tap wrench.
  12. Step 13
    Qashqai / Qashqai+2 I Van (J10, JJ10E) 1.6 dCi 2008 Wheel Bearing DIY replacement workshop manual
    Remove the brake caliper together with its bracket.
    Replacement: wheel bearing – NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E). Tip from AUTODOC experts:
    Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur. Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary.
  13. Step 14
    How to change Wheel Bearing on NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 2009 - tips and tricks
    Remove the brake disc.
  14. Step 15
    Step-by-step recommendations for DIY replacement NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 2010 1.6 dCi Wheel Bearing
    Unscrew the ball joint fastening to the steering knuckle. Use a combination spanner #18. Use a drive socket #18. Use a tap wrench.
  15. Step 16
    DIY replacement of Wheel Bearing on NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 2.0 Allrad 2011 is not an issue anymore with our step-by-step tutorial
    Remove the fastening bolt.
  16. Step 17
    How to change Wheel Bearing on NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 2006 - free PDF and video manuals
    Disconnect the ABS sensor wiring. Use a clip removal tool.
  17. Step 18
    How to replace NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 1.6 CVTC 2007 Wheel Bearing - step-by-step manuals and video guides
    Remove the wheel arch cover. Use a clip removal tool.
  18. Step 19
    NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 2.0 2008 Wheel Bearing replacement: free workshop manuals
    Detach the ABS sensor connector. Use a clip removal tool.
  19. Step 20
    Changing Wheel Bearing on NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 1.5 dCi 2009 by yourself
    Unscrew the lower fastener connecting the shock strut to the steering knuckle. Use a combination spanner #18. Use a drive socket #21. Use a ratchet wrench.
  20. Step 21
    How to remove NISSAN QASHQAI 1.6 dCi 2010 Wheel Bearing - online easy-to-follow instructions
    Disconnect the steering knuckle from the shock absorber strut.
  21. Step 22
    How to replace Wheel Bearing on NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 2011: download PDF manuals and video instructions
    Remove the fastening bolt.
  22. Step 23
    How hard is it to do yourself: Wheel Bearing replacement on NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 2.0 dCi Allrad 2012 - download illustrated guide
    Remove the drive shaft. Use a pin punch. Use a hammer.
    Replacement: wheel bearing – NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E). Tip:
    Make sure that the drive shaft is not unloaded (when the car is jacked).
  23. Step 24
    Need to know how to renew Wheel Bearing on NISSAN QASHQAI 2013? This free workshop manual will help you to do it yourself
    Remove the fastening nut.
  24. Step 25
    Changing of Wheel Bearing on NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 2014 won't be an issue if you follow this illustrated step-by-step guide
    Remove the fastening bolt.
  25. Step 26
    NISSAN QASHQAI 2.0 Wheel Bearing replacement: online guides and video tutorials
    Remove the steering knuckle together with the hub.
  26. Step 27
    Replacing Wheel Bearing on NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 2007 1.6 CVTC by yourself
    Clean the wheel hub fastener. Use a wire brush. Use WD-40 spray.
  27. Step 28
    Qashqai / Qashqai+2 I Van (J10, JJ10E) 1.6 dCi 2008 Wheel Bearing DIY replacement workshop manual
    Clean the ABS sensor mounting seat. Use a wire brush. Use WD-40 spray.
  28. Step 29
    How to change Wheel Bearing on NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 2009 - tips and tricks
    Unscrew the ABS sensor fastener. Use a drive socket #10. Use a ratchet wrench.
  29. Step 30
    Step-by-step recommendations for DIY replacement NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 2010 1.6 dCi Wheel Bearing
    Disconnect the ABS sensor. Use a flat screwdriver. Use water pump pliers.
  30. Step 31
    DIY replacement of Wheel Bearing on NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 2.0 Allrad 2011 is not an issue anymore with our step-by-step tutorial
    Unscrew the wheel hub axle nut. Use a drive socket #17. Use a ratchet wrench. Use a tap wrench.
  31. Step 32
    How to change Wheel Bearing on NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 2006 - free PDF and video manuals
    Remove the hub and the bearing together, since they are a sealed unit. Use a pin punch. Use a hammer.
  32. Step 33
    How to replace NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 1.6 CVTC 2007 Wheel Bearing - step-by-step manuals and video guides
    Remove the brake disc baffle plate.
  33. Step 34
    NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 2.0 2008 Wheel Bearing replacement: free workshop manuals
    Clean the hub bearing mounting seat. Use a wire brush.
  34. Step 35
    Changing Wheel Bearing on NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 1.5 dCi 2009 by yourself
    Apply special grease to the bearing assembly mounting seat. Use copper grease.
  35. Step 36
    How to remove NISSAN QASHQAI 1.6 dCi 2010 Wheel Bearing - online easy-to-follow instructions
    Install the brake disc baffle plate.
  36. Step 37
    How to replace Wheel Bearing on NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 2011: download PDF manuals and video instructions
    Install the new wheel hub with a bearing.
  37. Step 38
    How hard is it to do yourself: Wheel Bearing replacement on NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 2.0 dCi Allrad 2012 - download illustrated guide
    Screw the wheel hub axle nut. Use a drive socket #17. Use a ratchet wrench.
  38. Step 39
    Need to know how to renew Wheel Bearing on NISSAN QASHQAI 2013? This free workshop manual will help you to do it yourself
    Tighten the hub. Use a drive socket #17. Use a torque wrench. Tighten it to 70 nm torque.
  39. Step 40
    Changing of Wheel Bearing on NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 2014 won't be an issue if you follow this illustrated step-by-step guide
    Treat the ABS sensor fastener. Use a multipurpose grease.
  40. Step 41
    NISSAN QASHQAI 2.0 Wheel Bearing replacement: online guides and video tutorials
    Connect the ABS sensor.
  41. Step 42
    Replacing Wheel Bearing on NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 2007 1.6 CVTC by yourself
    Tighten the fastener that connects the ABS sensor to the steering knuckle. Use a drive socket #10. Use a torque wrench. Tighten it to 13 nm torque.
  42. Step 43
    Qashqai / Qashqai+2 I Van (J10, JJ10E) 1.6 dCi 2008 Wheel Bearing DIY replacement workshop manual
    Treat the fasteners of the wheel hub bearing. Use copper grease.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Searching for the right tyres?

Find out which tyre and wheel sizes are compatible with the NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) model.

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) Wheel Bearing replace by yourself - Scan QR-code and download AUTODOC CLUB app
Scan

To download the app:

  • - scan the QR code
  • - download from App Store
  • - download from Google Play
Autodoc CLUB App icon
DIY NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) Wheel Bearing replacement - online guide
Tips & tricks for your NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E)
View more
  • How to change Wheel bearings on NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 2.0 Allrad - replacement tricks
    Deep interior cleaning | Car transformation by detailing
  • Changing Hub bearing NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 1.6 CVTC - Replacement Tips
    Discover the 4 Key Reasons Your CHECK ENGINE Light Could Be On | AUTODOC Tips
  • Maintenance Hacks - NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) 2.0 Wheel bearing kit replacement guide
    Top 5 brake repair mistakes | AUTODOC tips
  • Replace Wheel hub bearing on NISSAN Qashqai / Qashqai+2 I Van (J10, JJ10E) - free video tips
    Engine Overheating? Replace Your Cooling Fan to Fix It | AUTODOC's How-To