Important!

This replacement procedure can be used for:
VOLVO C70 II Convertible (542) 2.4 D, VOLVO C70 II Convertible (542) 2.0 D, VOLVO C70 II Convertible (542) T5, VOLVO C70 II Convertible (542) D5, VOLVO C70 II Convertible (542) T5, VOLVO C70 II Convertible (542) 2.4 i, VOLVO C70 II Convertible (542) 2.4, VOLVO C70 II Convertible (542) D4, VOLVO C70 II Convertible (542) D3 … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Shock Absorber for C70 II Convertible (542) and other VOLVO models

Shock absorber

Suspension Strut

        Shock absorber for VOLVO C70 II Convertible (542) D3 Diesel (150 hp)
      
        Shock absorber for VOLVO C70 II Convertible (542) D4 Diesel (177 hp)
      
        Shock absorber for VOLVO C70 II Convertible (542) 2.4 Petrol (140 hp)
      
        Shock absorber for VOLVO C70 II Convertible (542) 2.4 i Petrol (170 hp)
      
        Shock absorber for VOLVO C70 II Convertible (542) T5 Petrol (220 hp)
      
        Shock absorber for VOLVO C70 II Convertible (542) D5 Diesel (180 hp)
      
        Shock absorber for VOLVO C70 II Convertible (542) T5 Petrol (230 hp)
      
        Shock absorber for VOLVO C70 II Convertible (542) 2.0 D Diesel (136 hp)
      
        Shock absorber for VOLVO C70 II Convertible (542) 2.4 D Diesel (163 hp)

Replacement: suspension strut – VOLVO C70 II Convertible. Tools you'll need:

                        Wire brush
                      
                        WD-40 spray
                      
                        Copper grease 
                      
                        Combination spanner #15
                      
                        Combination spanner #18
                      
                        Combination spanner #21
                      
                        Impact socket №13
                      
                        Impact socket №15
                      
                        Impact socket №18
                      
                        Impact socket №21
                      
                        HEX bit no.H5.
                      
                        HEX bit no.H6.
                      
                        Wheel impact socket #19
                      
                        Shock absorber socket
                      
                        Ratchet wrench
                      
                        Torque wrench
                      
                        Tap wrench
                      
                        Ball joint puller
                      
                        Hydraulic strut spring compressor
                      
                        Hydraulic transmission jack
                      
                        Fender cover
                      
                        Wheel chock

Buy tools

Replacement: suspension strut – VOLVO C70 II Convertible. Tip from AUTODOC:

Both shock struts of the front suspension should be replaced simultaneously.
The replacement procedure is identical for the left and right shock struts of the front suspension.
All work should be done with the engine stopped.

Replacement: suspension strut – VOLVO C70 II Convertible. Take the following steps:

Step 1

Open the bonnet.

Step 2

Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.

Step 3

Clean the fasteners of the shock strut upper mount. Use WD-40 spray.
Step 4

Loosen the upper fastener of the shock strut mount. Use a drive socket #13. Use a ratchet wrench.
Step 5

Secure the wheels with chocks.
Step 6

Loosen the wheel mounting bolts. Use wheel impact socket #19.
Step 7

Loosen the fastener of the driveshaft. Use a drive socket #13. Use a tap wrench.
Step 8

Raise the front of the car and secure on supports.

Step 9

Unscrew the wheel bolts.

Replacement: suspension strut – VOLVO C70 II Convertible. Professionals recommend:
To avoid injury, hold up the wheel when unscrewing the bolts.
Step 10

Remove the wheel.
Step 11

Remove the fastening bolt.
Step 12

Disconnect the ABS sensor cable fastener.
Step 13

Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray.
Step 14

Unscrew the fastener connecting the stabilizer link to the shock strut. Use a combination spanner #15. Use HEX No.H5. Use a ratchet wrench.
Step 15

Remove the stabilizer rod.
Step 16

Detach the brake hose from the shock strut.
Step 17

Clean the fasteners connecting the shock strut to the steering knuckle. Use a wire brush. Use WD-40 spray.
Step 18

Unscrew the lower fastener connecting the shock strut to the steering knuckle. Use a drive socket #15. Use a ratchet wrench. Use a tap wrench.
Step 19

Clean the fastener that connects the ball joint to the steering knuckle. Use a wire brush. Use WD-40 spray.
Step 20

Unscrew the ball joint fastening to the steering knuckle. Use a combination spanner #21.
Step 21

Disconnect the ball joint from the steering knuckle. Use a ball joint puller.
Step 22

Disconnect the lower arm from the steering knuckle.
Step 23

Remove the drive shaft.
Step 24

Prop up the steering knuckle. Use a hydraulic transmission jack.
Step 25

Release the lower fastener connecting the shock strut to the steering knuckle. Use a special drive socket to remove the shock absorber. Use a ratchet wrench.
Step 26

Remove the fastening bolt.
Step 27

Disconnect the steering knuckle from the shock absorber strut.
Step 28

Unscrew the top fastening of the shock strut mount.

Replacement: suspension strut – VOLVO C70 II Convertible. AUTODOC experts recommend:
To avoid injuries, hold the shock strut when undoing the fastening bolts.
Step 29

Remove the suspension strut.
Step 30

Set the shock absorber strut on the spring compressor tool.

Replacement: suspension strut – VOLVO C70 II Convertible. AUTODOC recommends:
Note that when using a spring compressor, spring coils need to be securely gripped, compressing the spring on the opposite sides.Ensure the correct position of the spring in the retainer.Make sure that the spring coils tightly entered the lock handles.
Step 31

Compress the spring.
Step 32

Remove the strut piston rod nut. Use a drive socket #18. Use HEX No.H6. Use a ratchet wrench.
Step 33

Remove the top mount of the shock absorber strut together with the mount bearing.
Step 34

Remove the shock absorber dust cap and the bump stop.

AUTODOC recommends:
Replacement: suspension strut – VOLVO C70 II Convertible. Carefully inspect the mount, the boot, and the bump stop of the shock absorber. Replace if necessary.
Step 35

Release the coil spring.
Step 36

Remove the spring.
Step 37

Remove the old shock absorber from the hydraulic coil spring compressor.

Replacement: suspension strut – VOLVO C70 II Convertible. AUTODOC experts recommend:
Before installing a new shock absorber you should pump it manually 3-5 times.
Step 38

Install the new shock absorber on the hydraulic coil spring compressor.
Step 39

Install the spring on the shock absorber.
Step 40

Compress the spring.
Step 41

Install the dust sleeve and the bump stop on the new shock absorber.
Step 42

Install the upper strut mount and the strut mount bearing.
Step 43

Tighten the shock strut piston rod nut. Use HEX No.H6. Use a drive socket #18. Use a torque wrench. Tighten it to 50 Nm torque.

Replacement: suspension strut – VOLVO C70 II Convertible. Tip:
Check to make sure the spring is positioned correctly. Avoid its misalignment.
Step 44

Decompress the spring.
Step 45

Remove the assembled shock strut.
Step 46

Install the shock strut into the wheel arch.
Step 47

Screw the top fastening of the shock strut mount. Do not tighten it.

AUTODOC recommends:
Important! Hold the suspension strut while screwing in the fastening bolts. VOLVO C70 II Convertible
Step 48

Treat the shock strut mounting seat on the steering knuckle. Use a wire brush. Use WD-40 spray.
Step 49

Fix the shock absorber strut on the steering knuckle.
Step 50

Install the fastening bolt. Use a drive socket #15.
Step 51

Remove the support from under the steering knuckle.

AUTODOC recommends:
Replacement: suspension strut – VOLVO C70 II Convertible. Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms.
Step 52

Clean the splines of the drive shaft CV joint. Use a wire brush. Use WD-40 spray.
Step 53

Install the drive shaft.
Step 54

Clean the ball joint mounting seat. Use a wire brush. Use WD-40 spray.
Step 55

Connect the ball joint to the steering knuckle. Connect the lower arm to the steering knuckle.
Step 56

Tighten the ball joint fastener. Use a combination spanner #21. Use a torque wrench. Tighten it to 70 Nm torque.
Step 57

Screw in the fastener that connects the shock strut to the steering knuckle. Use a combination spanner #18. Use a drive socket #21. Use a ratchet wrench. Use a tap wrench.

Step 58

Tighten the lower fasteners connecting the shock strut to the steering knuckle. Use a drive socket #15. Use a torque wrench. Tighten it to 90 Nm torque.
Step 59

Fasten the brake hose on the strut.
Step 60

Ιnstall the transverse stabilizer link.
Step 61

Tighten the fastener connecting the stabilizer link to the shock strut. Use a combination spanner #15. Use HEX No.H5. Use a torque wrench. Tighten it to 60 Nm torque.
Step 62

Connect the fastener of the ABS sensor cable to the shock absorber strut.
Step 63

Install and tighten the drive shaft bolt. Use a drive socket #13.
Step 64

Treat the shock strut fasteners. Use copper grease.

Step 65

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 66

Clean the brake disk surface. Use a brake cleaner.

AUTODOC recommends:
After applying the spray, wait a few minutes.
Step 67

Install the wheel.

AUTODOC recommends:
Important! Hold the wheel while screwing in the fastening bolts. VOLVO C70 II Convertible
Step 68

Screw in the wheel bolts. Use wheel impact socket #19.
Step 69

Lower the car.

Step 70

Tighten the upper fastener of the shock absorber strut mount. Use a drive socket #13. Use a torque wrench. Tighten it to 30 nm torque.
Step 71

Treat the shock strut fasteners. Treat the shock strut rod. Use copper grease.
Step 72

Tighten the bolt connecting the drive shaft to the wheel hub. Use a drive socket #13. Use a torque wrench. Tighten it to 35 Nm torque.+90°

AUTODOC recommends:
Important! Be sure to use new fasteners.
Step 73

Tighten the wheel bolts using a criss-cross pattern. Use a torque wrench. Tighten it to 110 Nm torque.
Step 74

Remove the fender protection cover.

Step 75

Close the hood.

Step 76

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

How to change front brake pads on VOLVO C70 II Convertible (542) – replacement guide

Free download PDF
1.56 MB
How to change rear brake pads on VOLVO C70 II Convertible (542) – replacement guide

Free download PDF
1.56 MB
How to change front brake discs on VOLVO C70 II Convertible (542) – replacement guide

Free download PDF
1.95 MB
How to change rear brake discs on VOLVO C70 II Convertible (542) – replacement guide

Free download PDF
1.83 MB
How to change front windshield wipers on VOLVO C70 II Convertible (542) – replacement guide

Free download PDF
604.16 KB
How to change front anti roll bar links on VOLVO C70 II Convertible (542) – replacement guide

Free download PDF
1.2 MB

How to change suspension strut on a car – replacement tutorial

Universal

Free download PDF
1.53 MB
How to change shock absorbers on a car – replacement tutorial

Universal

Free download PDF
1.07 MB
How to change front suspension strut on Volvo V70 BW – replacement guide

Free download PDF
4.1 MB
How to change rear shock absorbers on Volvo V70 BW – replacement guide

Free download PDF
1.76 MB
How to change rear shock absorbers on Volvo V70 SW – replacement guide

Free download PDF
2.19 MB
How to change front suspension strut on Volvo V50 MW – replacement guide

Free download PDF
3.6 MB

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!

Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.

Scan

To download the app:

- scan the QR code
- download from App Store
- download from Google Play

Petrol or diesel? What's the difference between these engines? | AUTODOC

4K views

Published on: 04/05/2021
How to restore a damaged thread | AUTODOC tips

5K views

Published on: 04/05/2023
What to do if your car's air conditioning isn't working properly | AUTODOC tips

6K views

Published on: 05/08/2021
DIY car soundproofing | AUTODOC tips

75K views

Published on: 15/04/2021