Disclaimer
How to change front strut mount on ABARTH 500C / 595C / 695C Convertible (312) – replacement guide
downloads:
2
Views:
37
Important!
This replacement procedure can be used for:
ABARTH 500C / 595C / 695C (312_) Convertible 1.4 (312.AXY1A, 312.AXY11), ABARTH 500C / 595C / 695C (312_) Convertible 1.4 (312.AXZ1A) … View more
The steps may slightly vary depending on the car design.
ABARTH 500C / 595C / 695C (312_) Convertible 1.4 (312.AXY1A, 312.AXY11), ABARTH 500C / 595C / 695C (312_) Convertible 1.4 (312.AXZ1A) … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Strut Mount for 500C / 595C / 695C (312_) Convertible and other ABARTH models
Alternative products

Wire brush
WD-40 spray
Copper grease
Combination spanner #19
Combination spanner #27
Ring spanner #17
Ring spanner #18
Ring spanner #27
Drive socket # 18
Drive socket # 19
HEX bit No.H7.
HEX bit No.H5.
Wheel impact socket #19
Ratchet wrench
Torque wrench
Round-nose pliers
Clip removal tool
Crow bar
Hydraulic transmission jack
Hydraulic strut spring compressor
Fender cover
Wheel chock
Replacement: strut mount – ABARTH 500C / 595C (312_). AUTODOC recommends:
- The replacement procedure is identical for the mounts of the left and right shock struts of the front suspension.
- Be sure to replace all self-locking nuts and bolts during installation.
- All work should be done with the engine stopped.
Replacement: strut mount – ABARTH 500C / 595C (312_). Use the following procedure:
- Step 1Open the bonnet.Step 2Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.Step 3
Remove the clips of the plastic cowl grille. Use a clip removal tool. - Step 4
Raise the wiper plastic cowl grille. - Step 5
Clean the fasteners of the shock strut upper mount. Use WD-40 spray. - Step 6
Unscrew the top fastening of the shock strut mount. Use a combination spanner #19. Use HEX No.H7. Use a ratchet wrench. - Step 7
Secure the wheels with chocks. - Step 8
Loosen the wheel mounting bolts. Use wheel impact socket #19. - Step 9Raise the front of the car and secure on supports.Step 10
Unscrew the wheel bolts.AUTODOC recommends:Important! Hold the wheel while unscrewing the fastening bolts. ABARTH 500C / 595C (312_) - Step 11
Remove the wheel. - Step 12
Disconnect the wiring and the brake hose from the bracket on the shock strut. Use round-nose pliers. - Step 13.1
Clean the fasteners connecting the stabiliser link to the shock strut, and those connecting the shock strut to the steering knuckle.Step 13.2
Use a wire brush. Use WD-40 spray. - Step 14
Unscrew the nut and remove the stabilizer rod from the shock strut. Use box wrench #18. Use a drive socket #18. Use HEX No.H5. - Step 15
Prop up the steering knuckle. Use a hydraulic transmission jack. - Step 16
Unscrew the lower fastener connecting the shock strut to the steering knuckle. Use box wrench #17. Use a drive socket #15. Use a ratchet wrench. - Step 17
Remove the support from under the steering knuckle. - Step 18
Disconnect the steering knuckle from the shock absorber strut. - Step 19
Unscrew the upper fastening of the shock absorber strut.Replacement: strut mount – ABARTH 500C / 595C (312_). AUTODOC experts recommend:To avoid injuries, hold the shock strut when undoing the fastening bolts. - Step 20
Remove the suspension strut. - Step 21
Set the shock absorber strut on the spring compressor tool.Replacement: strut mount – ABARTH 500C / 595C (312_). Tip:Note that when using a spring compressor, spring coils need to be securely gripped, compressing the spring on the opposite sides.Ensure the correct position of the spring in the retainer.Make sure that the spring coils tightly entered the lock handles. - Step 22
Compress the spring. - Step 23
Clean the shock absorber rod. Use a wire brush. Use WD-40 spray. - Step 24
Remove the strut piston rod nut. Use a combination spanner #27. Use HEX No.H7. - Step 25
Remove the top mount, the support bearing and the upper spring cup. - Step 26
Install the top mount, the strut mount bearing and the upper spring cup. Use a crowbar.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the ABARTH 500C / 595C / 695C Convertible (312) model
Popular maintenance tutorials for Abarth 500С Convertible
Complete guides for changing the Strut mount on different ABARTH 500 / 595 models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your ABARTH 500C / 595C / 695C (312_) Convertible
View more
Motorcycle fuel tank restoration
#TPMS Explained: Why Your Light is On and How to Respond Safely
DIY jack restoration | AUTODOC tips
Why does it burn oil? The main cause of oil consumption in EA888 Gen 1
Most commonly replaced car parts on ABARTH 500 / 595
Professional manuals for the most common ABARTH models
Time to replace parts? Get even better deals in our Shop app.

SCAN ME




























