Important!

This replacement procedure can be used for:
VW CC (358) 2.0 TDI, VW CC (358) 3.6 FSI 4motion, VW CC (358) 2.0 TSI, VW CC (358) 2.0 TDI, VW CC (358) 1.8 TSI, VW CC (358) 2.0 TFSI, VW CC (358) 1.8 TSI, VW CC (358) 2.0 TDI, VW CC (358) 2.0 TDI, VW CC (358) 1.4 TSI, VW CC (358) 2.0 TDI 4motion, VW CC (358) 2.0 TDI 4motion, VW CC (358) 2.0 TDI 4motion, VW CC (358) 1.4 TSI MultiFuel, VW CC (358) 1.4 TSI, VW CC (358) 2.0 TDI, VW CC (358) 2.0 TDI … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Control Arm for CC (358) and other VW models

Suspension arm

        Suspension arm for CC (358) Diesel (170 hp)
      
        Suspension arm for CC (358) Petrol (300 hp)
      
        Suspension arm for CC (358) Petrol (210 hp)
      
        Suspension arm for CC (358) Diesel (140 hp)
      
        Suspension arm for CC (358) Petrol (160 hp)
      
        Suspension arm for CC (358) Petrol (200 hp)
      
        Suspension arm for CC (358) Petrol (152 hp)
      
        Suspension arm for CC (358) Diesel (136 hp)
      
        Suspension arm for CC (358) Diesel (177 hp)

Replacement: front lower arm – VW CC (358). List of the tools you'll need:

                        Wire brush
                      
                        WD-40 spray
                      
                        Brake cleaner 
                      
                        Copper grease 
                      
                        Drive socket # 13 
                      
                        Drive socket # 16 
                      
                        Drive socket # 18 
                      
                        Torx bit T25
                      
                        Wheel impact socket #17
                      
                        Ratchet wrench
                      
                        Torque wrench
                      
                        Tap wrench
                      
                        Crow bar
                      
                        Wheel chock

Buy tools

Replacement: front lower arm – VW CC (358). AUTODOC experts recommend:

The replacement procedure is identical for the left and right lower control arms.
All work should be done with the engine stopped.

Replacement: front lower arm – VW CC (358). Take the following steps:

Step 1

Secure the wheels with chocks.

Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 3

Raise the front of the car and secure on supports.

Step 4

Unscrew the wheel bolts.

Replacement: front lower arm – VW CC (358). Tip:
To avoid injury, hold up the wheel when unscrewing the bolts.
Step 5

Remove the wheel.
Step 6

Undo the fasteners of the oil pan lower cover. Use a drive socket #13. Use Torx T25. Use a ratchet wrench.
Step 7

Remove the oil pan cover.
Step 8

Clean all joints of the arm. Use a wire brush. Use WD-40 spray.

AUTODOC recommends:
Replacement: front lower arm – VW CC (358). After applying the spray, wait a few minutes.Wear protective goggles.
Step 9

Unscrew the front arm fastener. Use a drive socket #18. Use a tap wrench.
Step 10

Unscrew the rear fastener connecting the control arm to the car body. Use a drive socket #18. Use a tap wrench.
Step 11

Unscrew the rear fastener connecting the control arm to the subframe. Use a drive socket #16. Use a tap wrench.
Step 12

Remove the rear fastener of the control arm (2 pieces).
Step 13

Unscrew the fastener connecting the ball joint to the suspension control arm. Use a drive socket #16. Use a tap wrench.
Step 14

Remove the front fastener of the control arm.
Step 15

Remove the rear fastener of the control arm.
Step 16

Remove the arm. Use a crowbar.
Step 17

Clean the mounting seats and the thread of the suspension arm. Use a wire brush. Use WD-40 spray.
Step 18

Install a new arm. Use a crowbar.

Replacement: front lower arm – VW CC (358). AUTODOC recommends:
During the installation process, use only new bolts and nuts.Do not damage the ball joint cover.
Step 19

Install the front fastener of the arm.
Step 20

Screw the front arm fastener. Use a drive socket #18. Use a ratchet wrench.
Step 21

Install the rear fastener of the control arm (2 pieces).
Step 22

Screw the rear fastener connecting the control arm to the car body. Use a drive socket #18. Use a ratchet wrench.
Step 23

Install the rear fastener of the control arm.

Step 24

Screw the rear fastener connecting the control arm to the subframe. Use a drive socket #16. Use a ratchet wrench.
Step 25

Tighten the fasteners of the ball joint. Use a drive socket #16. Use a torque wrench. Tighten it to 60 nm torque.
Step 26

Prop up the steering knuckle. Use a hydraulic transmission jack.
Step 27

Tighten the front fastener connecting the control arm to the subframe. Use a drive socket #18. Use a torque wrench. Tighten it to 70 Nm torque.+180°

AUTODOC recommends:
Important! Be sure to use new fasteners.
Step 28

Tighten the rear fastener connecting the arm to the car body. Use a drive socket #18. Use a torque wrench. Tighten it to 70 Nm torque.+180°

Replacement: front lower arm – VW CC (358). Tip from AUTODOC experts:
Important! Be sure to use new fasteners.
Step 29

Tighten the rear fastener connecting the arm to the body subframe. Use a drive socket #16. Use a torque wrench. Tighten it to 50 Nm torque.+90°

AUTODOC recommends:
Important! Be sure to use new fasteners.
Step 30

Remove the support from under the steering knuckle.

AUTODOC recommends:
Lower the hydraulic transmission jack smoothly, without jerks, to avoid damaging assemblies and mechanisms.
Step 31

Treat all joints of the arm. Use copper grease.
Step 32

Reinstall the oil pan lower cover.
Step 33

Tighten the fasteners of the oil pan lower cover. Use a drive socket #13. Use Torx T25. Use a ratchet wrench.
Step 34

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 35

Clean the brake disk surface. Use a brake cleaner.

Replacement: front lower arm – VW CC (358). Tip from AUTODOC:
After applying the spray, wait a few minutes.
Step 36

Install the wheel.

Replacement: front lower arm – VW CC (358). Professionals recommend:
To avoid injury, hold up the wheel when screwing in the fastening bolts.
Step 37

Screw in the wheel bolts. Use wheel impact socket #17.
Step 38

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #17. Use a torque wrench. Tighten it to 120 nm torque.

Step 39

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Searching for the right tyres?

Find out which tyre and wheel sizes are compatible with the VW CC (358) model.

Browse tyres

How to change rear strut mount on VW CC (358) – replacement guide

Free download PDF
2.77 MB
How to change front strut mount on VW CC (358) – replacement guide

Free download PDF
3.06 MB
How to change rear suspension lower trailing arm on VW CC (358) – replacement guide

Free download PDF
2.59 MB
How to change rear suspension lower control arm on VW CC (358) – replacement guide

Free download PDF
2.55 MB
How to change track rod end on VW CC (358) – replacement guide

Free download PDF
2.24 MB
How to change rear wheel bearing on VW CC (358) – replacement guide

Free download PDF
2.22 MB

How to change rear suspension lower trailing arm on VW CC (358) – replacement guide

Free download PDF
2.59 MB
How to change rear suspension lower control arm on VW CC (358) – replacement guide

Free download PDF
2.55 MB
How to change control arm on a car – replacement tutorial

Universal

Free download PDF
1.07 MB
How to change front lower arm on VW Polo 9N – replacement guide

Free download PDF
2.45 MB
How to change front lower arm on VW Golf 5 – replacement guide

Free download PDF
2.89 MB
How to change rear suspension lower control arm on VW Golf 6 – replacement guide

Free download PDF
2.47 MB

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!

Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.

Scan

To download the app:

- scan the QR code
- download from App Store
- download from Google Play

DIY starter repair | AUTODOC tips

40K views

Published on: 31/08/2023
Top 5 tips to prevent car rust | AUTODOC tips

5K views

Published on: 27/07/2023
The most common problems when buying a used car | AUTODOC

4K views

Published on: 10/11/2022
3 things that cause engine damage | AUTODOC tips

9K views

Published on: 07/10/2021