Important!

This replacement procedure can be used for:
NISSAN KUBISTAR (X76) 1.5 dCi, NISSAN KUBISTAR (X76) 1.2 16V, NISSAN KUBISTAR (X76) 1.5 dCi, NISSAN KUBISTAR (X76) 1.5 dCi … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

Alternative products

Suspension arm

Replacement: front lower arm – NISSAN KUBISTAR (X76). List of the tools you'll need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Brake cleaner 
                    
                      Copper grease 
                    
                      Combination spanner #16
                    
                      Combination spanner #18
                    
                      Drive socket # 12 
                    
                      Drive socket # 13 
                    
                      Drive socket # 16 
                    
                      Drive socket # 18 
                    
                      Torx bit T40
                    
                      Wheel impact socket #19
                    
                      Ratchet wrench
                    
                      Torque wrench
                    
                      Tap wrench
                    
                      Hammer
                    
                      Flat chisel
                    
                      Crow bar
                    
                      Wheel chock

Buy tools

Replacement: front lower arm – NISSAN KUBISTAR (X76). Tip:

The replacement procedure is identical for the left and right lower control arms.
All work should be done with the engine stopped.

Replacement: front lower arm – NISSAN KUBISTAR (X76). Take the following steps:

Step 1

Secure the wheels with chocks.
Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #19.
Step 3

Raise the front of the car and secure on supports.

Step 4

Unscrew the wheel bolts.

AUTODOC recommends:
Important! Hold the wheel while unscrewing the fastening bolts. NISSAN KUBISTAR (X76)
Step 5

Remove the wheel.
Step 6

Unscrew the wheel arch cover fasteners. Move the part aside.
Step 7

Clean the fasteners of the bumper reinforcement bar and of its bracket. Use a wire brush. Use WD-40 spray.
Step 8

Unscrew the fasteners of the bumper reinforcement bar bracket. Use a drive socket #18. Use a tap wrench.
Step 9

Unscrew the fasteners of the bumper reinforcement bar bracket. Use a drive socket #12. Use a tap wrench.
Step 10

Remove the bumper reinforcement bar.
Step 11

Clean all joints of the arm. Use a wire brush. Use WD-40 spray.
Step 12

Unscrew the front arm fastener. Use a drive socket #18. Use a tap wrench.
Step 13

Unscrew the stabilizer rod fasteners. Use a drive socket #13.
Step 14

Remove the stabilizer rod.
Step 15

Clean all joints of the arm. Use a wire brush. Use WD-40 spray.
Step 16

Unscrew the rear arm fastener. Use a combination spanner #18. Use a drive socket #18. Use a tap wrench.
Step 17

Clean the fastener connecting the ball joint to the steering knuckle. Use a wire brush. Use WD-40 spray.
Step 18

Unscrew the ball joint fastening to the steering knuckle. Use a combination spanner #16. Use a drive socket #16.
Step 19

Remove the fastening bolt.
Step 20

Release the fastener that connects the control arm ball joint to the steering knuckle. Use a flat metal-working chisel. Use a hammer.
Step 21

Disconnect the lower arm from the steering knuckle.
Step 22

Remove the fastening bolts.
Step 23

Remove the arm. Use a crowbar.
Step 24

Clean the mounting seats and the thread of the suspension arm. Use a wire brush. Use WD-40 spray.
Step 25

Install a new arm.

Replacement: front lower arm – NISSAN KUBISTAR (X76). Professionals recommend:
During the installation process, use only new bolts and nuts.Do not damage the ball joint cover.
Step 26

Install the fastening bolts.
Step 27

Connect the lower arm to the steering knuckle.
Step 28

Support the arm. Use a hydraulic transmission jack.
Step 29

Install the fastening bolt.
Step 30

Remove the support from under the arm.

AUTODOC recommends:
NISSAN KUBISTAR (X76) – Do not lower the transmission jack sharply to avoid damaging components and mechanisms of the car.
Step 31

Screw the fasteners of the ball joint. Use a drive socket #16. Use a combination spanner #16.
Step 32

Screw the front arm fastener. Use a combination spanner #18. Use a drive socket #18. Use a tap wrench.
Step 33

Screw the rear fastener connecting the control arm to the subframe. Use a combination spanner #18. Use a drive socket #18.
Step 34

Support the arm. Use a hydraulic transmission jack.
Step 35

Tighten the front fastener connecting the control arm to the subframe. Use a combination spanner #18. Use a drive socket #18. Use a torque wrench. Tighten it to 90 Nm torque.
Step 36

Tighten the rear fastener of the control arm. Use a combination spanner #18. Use a drive socket #18. Use a torque wrench. Tighten it to 90 nm torque.
Step 37

Remove the support from under the arm.

AUTODOC recommends:
Replacement: front lower arm – NISSAN KUBISTAR (X76). Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms.
Step 38

Tighten the ball joint fastener. Use a combination spanner #16. Use a drive socket #16. Use a torque wrench. Tighten it to 55 Nm torque.
Step 39

Install the bumper reinforcement bar.
Step 40

Screw in the fastener of the bumper reinforcement bar bracket. Use a drive socket #12. Use a ratchet wrench.
Step 41

Screw in the fastener of the bumper reinforcement bar bracket. Use a drive socket #18. Use a torque wrench. Tighten it to 70 Nm torque.
Step 42

Treat the bumper support bracket. Use copper grease.
Step 43

Install the wheel arch cover to its mounting seat.
Step 44

Ιnstall the transverse stabilizer link. Use a crowbar.
Step 45

Tighten the stabiliser link fastener. Use Torx T40. Use a drive socket #13. Use a torque wrench. Tighten it to 14 Nm torque.
Step 46

Treat all joints of the arm. Use copper grease.
Step 47

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 48

Clean the brake disk surface. Use a brake cleaner.

AUTODOC recommends:
Replacement: front lower arm – NISSAN KUBISTAR (X76). After applying the spray, wait a few minutes.
Step 49

Install the wheel.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. NISSAN KUBISTAR (X76)
Step 50

Screw in the wheel bolts. Use wheel impact socket #19.
Step 51

Lower the car and working in a cross order, tighten the wheel bolts. Use a torque wrench. Tighten it to 90 nm torque.
Step 52

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the NISSAN Kubistar (X76) model

Nissan Kubistar X76 tyre size

How to change track rod end on NISSAN KUBISTAR (X76) – replacement guide

Free download PDF
1.75 MB
How to change spark plugs on NISSAN KUBISTAR (X76) – replacement guide

Free download PDF
952.32 KB
How to change engine oil and filter on NISSAN KUBISTAR (X76) – replacement guide

Free download PDF
1.54 MB
How to change pollen filter on NISSAN KUBISTAR (X76) – replacement guide

Free download PDF
1.01 MB
How to change spark plugs on Nissan Qashqai J10 – replacement guide

Free download PDF
2.37 MB
How to change engine oil and filter on Nissan Qashqai J10 – replacement guide

Free download PDF
2.86 MB

How to change front lower arm on NISSAN Kubistar Van (X76) – replacement guide

Free download PDF
2.85 MB
How to change control arm on a car – replacement tutorial

Universal

Free download PDF
1.07 MB
How to change front lower arm on Nissan Qashqai J10 – replacement guide

Free download PDF
2.08 MB
How to change rear suspension lower control arm on Nissan Qashqai J10 – replacement guide

Free download PDF
1.84 MB
How to change front lower arm on Nissan X Trail T30 – replacement guide

Free download PDF
1.87 MB
How to change rear suspension lower trailing arm on Nissan X Trail T30 – replacement guide

Free download PDF
1.47 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

3 essential tips for choosing summer tyres | Get ready for warmer weather

4K views

Published on: 18/05/2023
How to Safely Wash Your Car in Winter Without Damage | AUTODOC tips

3K views

Published on: 31/01/2024
K2 ROTON wheel cleaner overview

4K views

Published on: 27/03/2025
5 reasons why your car is making a knocking sound

11K views

Published on: 05/06/2025