Important!

This replacement procedure can be used for:
NISSAN Kubistar Van (X76) 1.4, NISSAN Kubistar Van (X76) 1.2 16V, NISSAN Kubistar Van (X76) 1.2 … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

Alternative products

Coil spring

Replacement: coil springs – NISSAN KUBISTAR Box (X80). Tools you might need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Copper grease 
                    
                      Combination spanner #14
                    
                      Combination spanner #19
                    
                      Combination spanner #21
                    
                      Drive socket # 21 
                    
                      HEX bit No.H6.
                    
                      Wheel impact socket #19
                    
                      Pin punch
                    
                      Hammer
                    
                      Tap wrench
                    
                      Ratchet wrench
                    
                      Torque wrench
                    
                      Crow bar
                    
                      Hydraulic transmission jack
                    
                      Hydraulic strut spring compressor
                    
                      Fender cover
                    
                      Wheel chock

Buy tools

Replacement: coil springs – NISSAN KUBISTAR Box (X80). Tip from AUTODOC experts:

Both coil springs of the front suspension should be replaced simultaneously.
The replacement procedure is identical for the left and right coil springs of the front suspension.
Please note: all work on the car – NISSAN KUBISTAR Box (X80) – should be done with the engine switched off.

Carry out replacement in the following order:

Step 1

Open the bonnet.

Step 2

Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.

Step 3

Remove the shock strut mount cap. Use a crowbar.
Step 4

Loosen the upper fastener of the shock strut mount. Use a combination spanner #21. Use HEX No.H6. Use a ratchet wrench.
Step 5

Secure the wheels with chocks.
Step 6

Loosen the wheel mounting bolts. Use wheel impact socket #19.
Step 7

Raise the front of the car and secure on supports.

Step 8

Unscrew the wheel bolts.

AUTODOC recommends:
Important! Hold the wheel while unscrewing the fastening bolts. NISSAN KUBISTAR Box (X80)
Step 9

Remove the wheel.
Step 10

Clean the shock strut fasteners. Use a wire brush. Use WD-40 spray.
Step 11

Unscrew the lower fastener connecting the shock strut to the steering knuckle. Use a drive socket #21. Use a combination spanner #21. Use a tap wrench.
Step 12

Prop up the steering knuckle. Use a hydraulic transmission jack.
Step 13

Remove the fastening bolts (2 pieces). Use a hammer. Use a pin punch.
Step 14

Unscrew the upper fastening of the shock absorber strut. Use a drive socket #21.

AUTODOC recommends:
NISSAN KUBISTAR Box (X80) – To avoid injury, hold the suspension strut while unscrewing the fastening bolts.
Step 15

Remove the suspension strut.
Step 16

Set the shock absorber strut on the spring compressor tool.

Replacement: coil springs – NISSAN KUBISTAR Box (X80). Tip from AUTODOC:
Note that when using a spring compressor, spring coils need to be securely gripped, compressing the spring on the opposite sides.Ensure the correct position of the spring in the retainer.Make sure that the spring coils tightly entered the lock handles.
Step 17

Compress the spring.
Step 18

Remove the strut piston rod nut. Use HEX No.H6. Use a combination spanner #14. Use a ratchet wrench.
Step 19

Remove the top strut mount.
Step 20

Release the coil spring.
Step 21

Remove the spring.
Step 22

Remove the shock absorber dust cap and the bump stop.
Step 23

Install the boot and a bump stop onto the shock absorber.
Step 24

Install the spring on the shock absorber.
Step 25

Compress the spring.
Step 26

Install the top shock strut mount.
Step 27

Tighten the shock strut piston rod nut. Use HEX No.H6. Use a combination spanner #14. Use a torque wrench. Tighten it to 60 Nm torque.

Replacement: coil springs – NISSAN KUBISTAR Box (X80). AUTODOC recommends:
Check to make sure the spring is positioned correctly. Avoid its misalignment.
Step 28

Decompress the spring.
Step 29

Remove the assembled shock strut.
Step 30

Install the shock strut into the wheel arch. Tighten the upper fastening nut of the shock absorber strut. Do not tighten it.

AUTODOC recommends:
NISSAN KUBISTAR Box (X80) – To avoid injury, hold the suspension strut while screwing in the fastening bolts.
Step 31

Clean the mounting seats of the shock strut. Use a wire brush. Use WD-40 spray.
Step 32

Fix the shock absorber strut on the steering knuckle.
Step 33

Install and tighten new bolts of the steering knuckle. Use a drive socket #21. Use a combination spanner #21. Use a torque wrench. Tighten it to 140 Nm torque.
Step 34

Remove the support from under the steering knuckle.

AUTODOC recommends:
Replacement: coil springs – NISSAN KUBISTAR Box (X80). Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms.
Step 35

Clean the wheel rim mounting seat. Use a wire brush. Treat the contacting surface. Use copper grease.
Step 36

Install the wheel.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. NISSAN KUBISTAR Box (X80)
Step 37

Screw in the wheel bolts. Use wheel impact socket #19.
Step 38

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #19. Use a torque wrench. Tighten it to 110 Nm torque.
Step 39

Tighten the shock strut top mount. Use a combination spanner #21. Use HEX No.H6. Use a torque wrench. Tighten it to 62 Nm torque.
Step 40

Install the shock strut mount cap.
Step 41

Remove the fender protection cover.

Step 42

Close the hood.

Step 43

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the NISSAN Kubistar Van (X76) model

Nissan Kubistar Van X80 tyre size

How to change front suspension strut on NISSAN Kubistar Van (X76) – replacement guide

Free download PDF
2.29 MB
How to change front brake pads on NISSAN Kubistar Van (X76) – replacement guide

Free download PDF
1.45 MB
How to change front brake discs on NISSAN Kubistar Van (X76) – replacement guide

Free download PDF
1.48 MB
How to change front wheel bearing on NISSAN Kubistar Van (X76) – replacement guide

Free download PDF
3.4 MB
How to change serpentine belt on NISSAN Kubistar Van (X76) – replacement guide

Free download PDF
1.62 MB
How to change spark plugs on NISSAN Kubistar Van (X76) – replacement guide

Free download PDF
1.1 MB

How to change coil springs on a car – replacement tutorial

Universal

Free download PDF
1.91 MB
How to change rear coil springs on Nissan Qashqai J10 – replacement guide

Free download PDF
2.62 MB
How to change front coil springs on Nissan Qashqai J10 – replacement guide

Free download PDF
3.86 MB
How to change front coil springs on Nissan X Trail T30 – replacement guide

Free download PDF
2.76 MB
How to change rear coil springs on Nissan X Trail T30 – replacement guide

Free download PDF
2.99 MB
How to change front coil springs on Nissan Leaf ZE0 – replacement guide

Free download PDF
3.18 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

How to Get the Best Deals on Car Parts | Save Money with AUTODOC

2K views

Published on: 03/02/2022
Petrol or diesel: The engine showdown! | AUTODOC

4K views

Published on: 04/05/2021
How to inspect and troubleshoot your car heater when it’s not working

5K views

Published on: 11/02/2021
#DIY Wheel Rim Restoration: Revive Scratches and Chips Easily!

7K views

Published on: 18/07/2024