
Disclaimer
How to change front brake discs on RENAULT 21 Van – replacement guide
downloads:
0
Views:
2

Recommended replacement interval for the part category Brake disc : 50000 km
Important!
This replacement procedure can be used for:
RENAULT 21 Box (S48_) 1.7 … View more
The steps may slightly vary depending on the car design.
RENAULT 21 Box (S48_) 1.7 … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Brake Discs for 21 Box (S48_) and other RENAULT models
Brake disc
Alternative products

Wire brush
WD-40 spray
Brake cleaner
Copper grease
Torx bit T30
Impact socket №18
Wheel impact socket #19
Tap wrench
Ratchet wrench
Torque wrench
Impact screwdriver
Crow bar
Wheel chock
Replacement: brake discs – RENAULT 21 Box (S48_). AUTODOC experts recommend:
- Replace the brake disks on the car RENAULT 21 Box (S48_) in complete set for each axis. Regardless of the state of components. This will ensure even braking.
- The replacement procedure is identical for both brake disks on the same axle.
- When changing the brake discs, always replace the brake pads.
- All work should be done with the engine stopped.
Replacement: brake discs – RENAULT 21 Box (S48_). Recommended sequence of steps:
- Step 1Open the bonnet. Unscrew the brake fluid reservoir cap.Step 2Secure the wheels with chocks.
- Step 3Loosen the wheel mounting bolts. Use wheel impact socket #19.
- Step 4Raise the front of the car and secure on supports.Step 5Unscrew the wheel bolts.Replacement: brake discs – RENAULT 21 Box (S48_). Tip:To avoid injury, hold up the wheel when unscrewing the bolts.
- Step 6Remove the wheel.
- Step 7Spread the brake pads. Use a crowbar.
- Step 8Clean the brake caliper bracket from dirt and dust. Use a wire brush. Use WD-40 spray.
- Step 9Unscrew the caliper bracket fastening. Use a drive socket #18. Use a ratchet wrench. Use a tap wrench.
- Step 10Remove the brake caliper together with its bracket.AUTODOC recommends:Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur.
- Step 11Unscrew the brake disc fastening. Use Torx T30. Use an impact screwdriver.
- Step 12Remove the brake disc.
- Step 13Clean the hub. Use a wire brush. Treat the contacting surface. Use copper grease.
- Step 14Install the new brake disc on the hub and tighten the screws.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the RENAULT 21 Van model
Popular maintenance tutorials for 21 K48
Complete guides for changing the Brake rotors on different RENAULT 21 models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your RENAULT 21 Box (S48_)
View more
- How to Swap an M50 Engine in a BMW E30 Turbo | AUTODOC Project
- Top 5 reasons why your car squeals | AUTODOC Tips
- Fuse Replacement Made Simple: Step-by-Step Guide | AUTODOC
- Understanding Car Tools: The Key Differences You Need to Know | AUTODOC tips
Most commonly replaced car parts on RENAULT 21
Time to replace parts? Get even better deals in our Shop app.

SCAN ME