Important!
This replacement procedure can be used for:
PEUGEOT 306 Break (7E, N3, N5) 1.4, PEUGEOT 306 Break (7E, N3, N5) 1.9 TD, PEUGEOT 306 Break (7E, N3, N5) 1.9 D, PEUGEOT 306 Break (7E, N3, N5) 1.8 16V, PEUGEOT 306 Break (7E, N3, N5) 1.8, PEUGEOT 306 Break (7E, N3, N5) 1.6, PEUGEOT 306 Break (7E, N3, N5) 2.0, PEUGEOT 306 Break (7E, N3, N5) 1.9 D, PEUGEOT 306 Break (7E, N3, N5) 1.9 D, PEUGEOT 306 Break (7E, N3, N5) 2.0 HDI 90, PEUGEOT 306 Break (7E, N3, N5) 1.6, PEUGEOT 306 Break (7E, N3, N5) 1.9 D, PEUGEOT 306 Break (7E, N3, N5) 2.0 16V, PEUGEOT 306 Break (7E, N3, N5) 1.9 TD, PEUGEOT 306 Break (7E, N3, N5) 1.8 D View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Anti Roll Bar Links for 306 Break (7E, N3, N5) and other PEUGEOT models
Tools
Replacement: anti roll bar links – PEUGEOT 306 Break (7E, N3, N5). Tools you might need:
Wire brush
WD-40 spray
Brake cleaner
Ceramic grease
Copper grease
Torque wrench
Combination spanner #17
Drive socket # 17
HEX No.H6 bit socket
Wheel impact socket #19
Ratchet wrench
Wheel chock
Replacement: anti roll bar links – PEUGEOT 306 Break (7E, N3, N5). Tip from AUTODOC:
  • Replace the stabiliser links on PEUGEOT 306 Break (7E, N3, N5) in pairs.
  • The replacement procedure is identical for both stabiliser links on the same axle.
  • Please note: all work on the car – PEUGEOT 306 Break (7E, N3, N5) – should be done with the engine switched off.
Carry out replacement in the following order:
  1. Step 1
    Secure the wheels with chocks.
    Step 2
    How to change Anti Roll Bar Links on Peugeot 306 Estate 1994 - free PDF and video manuals
    Loosen the wheel mounting bolts. Use wheel impact socket #19.
  2. Step 3
    Raise the car.
    AUTODOC recommends:
    If you are using a jack, make sure it rests on a flat surface without any unevenness.Be sure to additionally secure the car with jack stands.
    Step 4
    How to replace PEUGEOT 306 Break (7E, N3, N5) 2.0 HDI 90 1995 Anti Roll Bar Links - step-by-step manuals and video guides
    Unscrew the wheel bolts.
    AUTODOC recommends:
    Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. PEUGEOT 306 Break (7E, N3, N5)
  3. Step 5
    Peugeot 306 Estate 1.6 1996 Anti Roll Bar Links replacement: free workshop manuals
    Remove the wheel.
  4. Step 6
    Changing Anti Roll Bar Links on PEUGEOT 306 Break (7E, N3, N5) 1.4 1997 by yourself
    Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray.
  5. Step 7
    How to remove PEUGEOT 306 1.9 TD 1998 Anti Roll Bar Links - online easy-to-follow instructions
    Unscrew the fastener connecting the stabilizer link to the shock strut. Use a drive socket #17. Use a ratchet wrench.
  6. Step 8
    How to replace Anti Roll Bar Links on PEUGEOT 306 Break (7E, N3, N5) 1999: download PDF manuals and video instructions
    Unscrew the fastener connecting the stabilizer link to the stabilizer bar. Use a combination spanner #17. Use HEX No.H6. Use a ratchet wrench.
  7. Step 9
    How hard is it to do yourself: Anti Roll Bar Links replacement on Peugeot 306 Estate 1.8 2000 - download illustrated guide
    Remove the stabiliser link.
    Replacement: anti roll bar links – PEUGEOT 306 Break (7E, N3, N5). Professionals recommend:
    Examine stabiliser bushes. Replace them if needed.
  8. Step 10
    Need to know how to renew Anti Roll Bar Links on PEUGEOT 306 2001? This free workshop manual will help you to do it yourself
    Clean the mounting seats of the stabiliser link. Use a wire brush. Use WD-40 spray.
  9. Step 11
    Changing of Anti Roll Bar Links on Peugeot 306 Estate 2002 won't be an issue if you follow this illustrated step-by-step guide
    Treat the thread of the sway bar link fasteners. Use copper grease.
  10. Step 12
    PEUGEOT 306 2.0 HDI 90 Anti Roll Bar Links replacement: online guides and video tutorials
    Install a new stabiliser link and tighten the fasteners. Use a drive socket #17. Use a ratchet wrench.
  11. Step 13
    Replacing Anti Roll Bar Links on Peugeot 306 Estate 1995 2.0 HDI 90 by yourself
    Tighten the fastener connecting the stabilizer link to the stabilizer bar. Use a drive socket #17. Use a torque wrench. Tighten it to 40 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Searching for the right tyres?

Find out which tyre and wheel sizes are compatible with the PEUGEOT 306 Estate model.

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
PEUGEOT 306 Break (7E, N3, N5) Anti Roll Bar Links replace by yourself - Scan QR-code and download AUTODOC CLUB app
Scan

To download the app:

  • - scan the QR code
  • - download from App Store
  • - download from Google Play
DIY PEUGEOT 306 Break (7E, N3, N5) Anti Roll Bar Links replacement - online guide
Tips & tricks for your PEUGEOT 306 Break (7E, N3, N5)
View more
  • How to change Drop links on PEUGEOT 306 Break (7E, N3, N5) 1.8 16V - replacement tricks
    Why do your brakes squeak? | AUTODOC tips
  • Changing Stabilizer link Peugeot 306 Estate 2.0 HDI 90 - Replacement Tips
    The most common problems when buying a used car | AUTODOC
  • Maintenance Hacks - PEUGEOT 306 Break (7E, N3, N5) 1.6 Sway bar link replacement guide
    Things you should never do with your manual transmission | AUTODOC tips
  • Replace Drop link on Peugeot 306 Estate - free video tips
    How and why to check your oil | AUTODOC tips