Important!

This replacement procedure can be used for:
BMW 1 Coupe (E82) 118 d, BMW 1 Coupe (E82) 135 i, BMW 1 Coupe (E82) 120d, BMW 1 Coupe (E82) 123d, BMW 1 Coupe (E82) 125i, BMW 1 Coupe (E82) 120d, BMW 1 Coupe (E82) 120 i, BMW 1 Coupe (E82) 118 d, BMW 1 Coupe (E82) 120 i … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

Alternative products

Anti-roll bar link

Replacement: anti roll bar links – BMW 1 Coupe (E82). AUTODOC experts recommend:

                      Wire brush
                    
                      WD-40 spray
                    
                      Brake cleaner 
                    
                      Copper grease 
                    
                      Combination spanner #17
                    
                      Drive socket # 16 
                    
                      Wheel impact socket #17
                    
                      Ratchet wrench
                    
                      Torque wrench
                    
                      Wheel chock

Buy tools

AUTODOC recommends:

Replace the stabiliser links on BMW 1 Coupe (E82) in pairs.
The replacement procedure is identical for both stabiliser links on the same axle.
Please note: all work on the car – BMW 1 Coupe (E82) – should be done with the engine switched off.

Carry out replacement in the following order:

Step 1

Secure the wheels with chocks.
Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 3

Raise the front of the car and secure on supports.

Step 4

Unscrew the wheel bolts.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. BMW 1 Coupe (E82)
Step 5

Remove the wheel.
Step 6

Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray.

Step 7

Unscrew the fastener connecting the stabilizer link to the shock strut. Use a combination spanner #17. Use a drive socket #16. Use a ratchet wrench.
Step 8

Unscrew the fastener connecting the stabilizer link to the stabilizer bar. Use a combination spanner #17 (2 pieces).
Step 9

Remove the stabilizer rod.

Replacement: anti roll bar links – BMW 1 Coupe (E82). Tip from AUTODOC experts:
Examine stabiliser bushes. Replace them if needed.
Step 10

Clean the mounting seats of the stabiliser link. Use a wire brush. Use WD-40 spray.

Step 11

Install a new rod, tighten the fasteners.
Step 12

Tighten the fastener connecting the stabilizer link to the stabilizer bar. Use a combination spanner #17 (2 pieces). Use a torque wrench. Tighten it to 58 Nm torque.
Step 13

Tighten the fastener connecting the stabilizer link to the shock strut. Use a combination spanner #17. Use a drive socket #16. Use a torque wrench. Tighten it to 58 Nm torque.
Step 14

Treat all joints of the stabiliser link. Use copper grease.

Step 15

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 16

Clean the brake disk surface. Use a brake cleaner.

AUTODOC recommends:
Replacement: anti roll bar links – BMW 1 Coupe (E82). After applying the spray, wait a few minutes.
Step 17

Install the wheel.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. BMW 1 Coupe (E82)
Step 18

Screw in the wheel bolts. Use wheel impact socket #17.
Step 19

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #17. Use a torque wrench. Tighten it to 120 nm torque.
Step 20

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the BMW 1 Coupe (E82) model

BMW E82 tyre size

How to change front lower arm on BMW E82 – replacement guide

Free download PDF
1.62 MB
How to change front strut mount on BMW E82 – replacement guide

Free download PDF
4.61 MB
How to change rear strut mount on BMW E82 – replacement guide

Free download PDF
2.55 MB
How to change front wheel bearing on BMW E82 – replacement guide

Free download PDF
4 MB
How to change rear anti roll bar links on BMW 1 Coupe (E82) – replacement guide

Free download PDF
1.06 MB
How to change rear upper arm on BMW 1 Coupe (E82) – replacement guide

Free download PDF
1.24 MB

How to change front anti roll bar links on BMW 1 Hatchback (E87) – replacement guide

Free download PDF
1.15 MB
How to change rear anti roll bar links on BMW 1 Hatchback (E87) – replacement guide

Free download PDF
1.06 MB
How to change rear anti roll bar links on BMW 1 Coupe (E82) – replacement guide

Free download PDF
1.06 MB
How to change front anti roll bar links on BMW 1 Hatchback (E81) – replacement guide

Free download PDF
1.15 MB
How to change rear anti roll bar links on BMW 1 Hatchback (E81) – replacement guide

Free download PDF
1.06 MB
How to change front anti roll bar links on BMW 1 Convertible (E88) – replacement guide

Free download PDF
1.15 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

Transform Your Engine Bay: Affordable Valve Cover Restoration with AUTODOC

8K views

Published on: 29/06/2023
The most common problems when buying a used car | AUTODOC

4K views

Published on: 10/11/2022
What to do if the ABS light comes on: DIY Diagnostics Tips

8K views

Published on: 11/03/2021
Checking the starter without removing it | AUTODOC tips

28K views

Published on: 01/12/2020