Disclaimer
How to change front anti roll bar links on AUDI Cabriolet (8G7, B4) – replacement guide
downloads:
3
Views:
20
Important!
This replacement procedure can be used for:
AUDI Cabriolet (8G7, B4) 2.0 E, AUDI Cabriolet (8G7, B4) 2.3 E, AUDI Cabriolet (8G7, B4) 2.6, AUDI Cabriolet (8G7, B4) 2.8, AUDI Cabriolet (8G7, B4) 2.0 16V, AUDI Cabriolet (8G7, B4) 1.9 TDI, AUDI Cabriolet (8G7, B4) 1.8 … View more
The steps may slightly vary depending on the car design.
AUDI Cabriolet (8G7, B4) 2.0 E, AUDI Cabriolet (8G7, B4) 2.3 E, AUDI Cabriolet (8G7, B4) 2.6, AUDI Cabriolet (8G7, B4) 2.8, AUDI Cabriolet (8G7, B4) 2.0 16V, AUDI Cabriolet (8G7, B4) 1.9 TDI, AUDI Cabriolet (8G7, B4) 1.8 … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Anti Roll Bar Links for Cabriolet (8G7, B4) and other AUDI models
Alternative products

Wire brush
WD-40 spray
Brake cleaner
Copper grease
High-temperature ceramic grease
Torque wrench
Combination spanner #16
Combination spanner #17
Drive socket # 17
Wheel impact socket #17
Ratchet wrench
Wheel chock
Replacement: anti roll bar links – AUDI CABRIOLET (8G7, B4). AUTODOC recommends:
- Replace the stabiliser links on AUDI CABRIOLET (8G7, B4) in pairs.
- The replacement procedure is identical for both stabiliser links on the same axle.
- Please note: all work on the car – AUDI CABRIOLET (8G7, B4) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1
Secure the wheels with chocks. - Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #17. - Step 3Raise the front of the car and secure on supports.Step 4
Unscrew the wheel bolts.AUTODOC recommends:Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. AUDI CABRIOLET (8G7, B4) - Step 5
Remove the wheel. - Step 6
Clean all joints of the stabiliser link. Use a wire brush. Use WD-40 spray. - Step 7
Unscrew the fastener connecting the stabilizer link to the shock strut. Use a combination spanner #16. Use a drive socket #17. Use a ratchet wrench. - Step 8
Unscrew the fastener connecting the stabilizer link to the stabilizer bar. Use a combination spanner #16. Use a combination spanner #17. - Step 9
Remove the stabilizer rod.Replacement: anti roll bar links – AUDI CABRIOLET (8G7, B4). AUTODOC experts recommend:Examine the stabiliser bushes. Replace them if necessary. - Step 10
Clean the mounting seats of the stabiliser link. Use a wire brush. Use WD-40 spray. - Step 11
Install a new stabiliser link and tighten the fasteners.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the AUDI Cabriolet B4 (8G7) model
Popular maintenance tutorials for Audi Cabriolet 8g7 b4
Complete guides for changing the Drop links on different AUDI CABRIOLET models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your AUDI Cabriolet (8G7, B4)
View more
Can You Hear Your Brakes Squeaking? Learn the Causes and DIY Solutions! | AUTODOC Tips
DIY rear axle restoration | Drivetrain restoration – Part 2
How to replace a timing chain yourself
Discover the 4 Key Reasons Your CHECK ENGINE Light Could Be On | AUTODOC Tips
Most commonly replaced car parts on AUDI CABRIOLET
Time to replace parts? Get even better deals in our Shop app.

SCAN ME
























