Recommended replacement interval for the part category Oil filter : 12 month / 15000 km

Important!

This replacement procedure can be used for:
TOYOTA Highlander I (XU20) 2.4 4WD (ACU25_), TOYOTA Highlander I (XU20) 2.4 (ACU20_), TOYOTA Highlander I (XU20) 2.4 (ACU20_) … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

Alternative products

Oil filter

Replacement: engine oil and filter – TOYOTA KLUGER (_MCU2_, _ACU2_). Tools you might need:

                      Wire brush
                    
                      All-purpose cleaning spray
                    
                      Torque wrench
                    
                      Drive socket # 14 
                    
                      Oil filter cup socket 65-14F
                    
                      Ratchet wrench
                    
                      Funnel
                    
                      Oil drain pan
                    
                      Fender cover

Buy tools

Replacement: engine oil and filter – TOYOTA KLUGER (_MCU2_, _ACU2_). Tip from AUTODOC:

Replace the oil filter every time when changing motor oil.
Wear gloves to prevent contact with hot liquid.
Please note: all work on the car – TOYOTA KLUGER (_MCU2_, _ACU2_) – should be done with the engine switched off.

Carry out replacement in the following order:

Step 1

Open the hood.

Step 2

Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.

Step 3

Pull up the oil dipstick.
Step 4

Unscrew the oil filler plug.
Step 5

Lift the car using a jack or place it over an inspection pit.

Replacement: engine oil and filter – TOYOTA KLUGER (_MCU2_, _ACU2_). AUTODOC recommends:
The vehicle must be on even keel, and if it is at an angle, the drain plug must be at the lowest point.
Step 6

Put a waste oil container with at least 5 l capacity under the drainage hole.

Step 7

Clean the area of the oil pan drainage hole. Use a wire brush. Use all-purpose cleaning spray.
Step 8

Unscrew the drain plug. Use a drive socket #14. Use a ratchet wrench.
Step 9

Drain the used oil.

Replacement: engine oil and filter – TOYOTA KLUGER (_MCU2_, _ACU2_). AUTODOC experts recommend:
Caution! The oil may be hot.Wait until the oil has completely drained from the drainage hole.
Step 10

Clean the oil filter. Use all-purpose cleaning spray.
Step 11

Unscrew the oil filter. Use the 65-14F socket. Use a ratchet wrench.
Step 12

Remove the oil filter.
Step 13

Clean the oil filter seat. Use all-purpose cleaning spray.
Step 14

Lubricate the rubber seal of the new filter with a little amount of fresh oil.
Step 15

Install a new oil filter.
Step 16

Tighten the oil filter. Remember to observe the recommended tightening torque. Use the 65-14F socket. Use a torque wrench. Tighten it to 24 Nm torque.
Step 17

Clean the area of the oil pan drainage hole. Use all-purpose cleaning spray.
Step 18

Screw in the new drainage plug and tighten it. Use a drive socket #14. Use a torque wrench. Tighten it to 25 Nm torque.
Step 19

Clean the area of the oil pan drainage hole. Use all-purpose cleaning spray.
Step 20

Lower the car.

Step 21

Remove the oil filler cap.
Step 22

Insert the funnel.
Step 23

Pour new oil into the engine in the amount recommended by the car manufacturer.

AUTODOC recommends:
Use the oil recommended by the manufacturer.
Step 24

Check the oil level using the dipstick. Top up oil if necessary.

Please note!
The oil level should be between the Min and Max marks.
Step 25

Install the oil filler cap.

Step 26

Tighten the oil filler cap.
Step 27

Run the engine for a few minutes.

Step 28

After the oil pressure warning light goes out, stop the engine.

Replacement: engine oil and filter – TOYOTA KLUGER (_MCU2_, _ACU2_). Tip from AUTODOC:
Note that oil pressure warning light, which indicates insufficient pressure in the lubrication system, may be on for a longer time than usual. After a few seconds, the oil will fill all the channels, and the light will go out.
Step 29

Check the oil level 5 minutes after the stop of the engine operation using a dipstick and add oil if necessary.

Please note!
The oil level should be between the Min and Max marks.Make sure that the oil filler cap is properly tightened.Check the threaded plug of the drainage hole and the oil filter seal for tightness. If necessary, carefully tighten them up.
Step 30

Remove the fender protection cover.

Step 31

Close the hood.

Replacement: engine oil and filter – TOYOTA KLUGER (_MCU2_, _ACU2_). Professionals recommend:
To protect the environment from pollution, be sure to dispose of the used filters at special collection points.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the TOYOTA Highlander I (XU20) model

TOYOTA KLUGER (_MCU2_, _ACU2_) tyre size

How to change pollen filter on TOYOTA Highlander I (XU20) – replacement guide

Free download PDF
655.36 KB
How to change spark plugs on TOYOTA Highlander I (XU20) – replacement guide

Free download PDF
1.68 MB
How to change front windshield wipers on TOYOTA Highlander I (XU20) – replacement guide

Free download PDF
542.72 KB
How to change rear windshield wipers on TOYOTA Highlander I (XU20) – replacement guide

Free download PDF
593.92 KB
How to change engine oil and filter on Toyota Aygo AB1 – replacement guide

Free download PDF
2.32 MB
How to change engine oil and filter on Toyota Auris E15 – replacement guide

Free download PDF
2.23 MB

How to change engine oil and filter on TOYOTA Highlander IV (GSU7_, AXUH7_) – replacement guide

Free download PDF
1.44 MB
How to change engine oil and filter on a car – replacement tutorial

Universal

Free download PDF
2.82 MB
How to change engine oil and filter on Toyota Aygo AB1 – replacement guide

Free download PDF
2.32 MB
How to change engine oil and filter on Toyota Auris E15 – replacement guide

Free download PDF
2.23 MB
How to change engine oil and filter on Toyota Prado J120 – replacement guide

Free download PDF
2.23 MB
How to change engine oil and filter on Toyota Yaris Mk2 – replacement guide

Free download PDF
1.87 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

Prevent Breakdowns: Key Car Checks After Winter | AUTODOC Guide

3K views

Published on: 23/03/2023
How to Prevent Premature Wear on Your Car Boot Damper | AUTODOC

5K views

Published on: 04/07/2021
Top 4 Car Cleaning Products to Protect Your Car's Body | AUTODOC Tips

2K views

Published on: 26/08/2021
The Ultimate Guide to Engine Bay Cleaning | AUTODOC

6K views

Published on: 11/09/2020