
Disclaimer
How to change engine oil and filter on SKODA Octavia II Hatchback (1Z3) – replacement guide
downloads:
16
Views:
402

Recommended replacement interval for the part category Oil filter : 1 year / 15000 km
Important!
This replacement procedure can be used for:
SKODA OCTAVIA (1Z3) 1.6 MultiFuel, SKODA OCTAVIA (1Z3) 1.6, SKODA OCTAVIA (1Z3) 1.6 LPG … View more
The steps may slightly vary depending on the car design.
SKODA OCTAVIA (1Z3) 1.6 MultiFuel, SKODA OCTAVIA (1Z3) 1.6, SKODA OCTAVIA (1Z3) 1.6 LPG … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Oil Filter for OCTAVIA (1Z3) and other SKODA models
Oil filter
Alternative products

All-purpose cleaning spray
Torque wrench
Drive socket # 19
Oil filter cup socket 76/14-F
Ratchet wrench
Funnel
Oil drain pan
Fender cover
Replacement: engine oil and filter – SKODA OCTAVIA (1Z3). AUTODOC recommends:
- Replace the oil filter every time when changing motor oil.
- Wear gloves to prevent contact with hot liquid.
- Use only new O-rings during installation.
- Please note: all work on the car – SKODA OCTAVIA (1Z3) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1Lift the car using a jack or place it over an inspection pit.Replacement: engine oil and filter – SKODA OCTAVIA (1Z3). AUTODOC experts recommend:The vehicle must be on even keel, and if it is at an angle, the drain plug must be at the lowest point.Unscrew the oil filler plug.Step 2Put a waste oil container with at least 5 l capacity under the drainage hole.
- Step 3Clean the area of the oil pan drainage hole. Use a wire brush. Use all-purpose cleaning spray.Step 4Unscrew the drain plug. Use a drive socket #19. Use a ratchet wrench.
- Step 5Drain the used oil.Replacement: engine oil and filter – SKODA OCTAVIA (1Z3). Professionals recommend:Caution! The oil may be hot.Wait until the oil has completely drained from the drainage hole.
- Step 6Clean the area of the oil pan drainage hole.
- Step 7Screw in the new drainage plug and tighten it. Use a drive socket #19. Use a torque wrench. Tighten it to 30 nm torque.
- Step 8Clean the area of the oil pan drainage hole. Use all-purpose cleaning spray.
- Step 9Unscrew the oil filter. Use the 76/14-F socket. Use a ratchet wrench.
- Step 10Put the old oil filter in the container.
- Step 11Clean the oil filter seat. Use all-purpose cleaning spray.Step 12Screw the new filter into its place. Use the 76/14-F socket. Observe the recommended tightening torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the SKODA Octavia II Hatchback (1Z3) model
Popular maintenance tutorials for Skoda Octavia Mk2
Complete guides for changing the Oil filters on different SKODA OCTAVIA models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your SKODA OCTAVIA (1Z3)
View more
- Prevent Breakdowns: Key Car Checks After Winter | AUTODOC Guide
- Top 5 Mistakes to Avoid for Safe Engine Bay Repairs | AUTODOC Tips
- How to fix your car with AUTODOC CLUB
- Initial Car Inspection: What to Check Before You Buy
Most commonly replaced car parts on SKODA OCTAVIA
Time to replace parts? Get even better deals in our Shop app.

SCAN ME