Recommended replacement interval for the part category Oil filter : 1 year / 20000 km

Important!

This replacement procedure can be used for:
HONDA STREAM (RN) 2.0 16V (RN3), HONDA STREAM (RN) 1.7 16V (RN1) … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

Alternative products

Oil filter

Replacement: engine oil and filter – HONDA STREAM (RN). List of the tools you'll need:

                      Wire brush
                    
                      All-purpose cleaning spray
                    
                      Torque wrench
                    
                      Drive socket # 17
                    
                      Oil filter cup socket 65/14-F
                    
                      Ratchet wrench
                    
                      Funnel
                    
                      Oil drain pan

Buy tools

Replacement: engine oil and filter – HONDA STREAM (RN). AUTODOC recommends:

Replace the oil filter every time when changing motor oil.
Wear gloves to prevent contact with hot liquid.
Use only new O-rings during installation.
Please note: all work on the car – HONDA STREAM (RN) – should be done with the engine switched off.

Carry out replacement in the following order:

Step 1

Lift the car using a jack or place it over an inspection pit.

Replacement: engine oil and filter – HONDA STREAM (RN). AUTODOC experts recommend:
The vehicle must be on even keel, and if it is at an angle, the drain plug must be at the lowest point.Unscrew the oil filler plug.
Step 2

Put a waste oil container with at least 4 l capacity under the drainage hole.
Step 3

Clean the area of the oil pan drainage hole. Use a wire brush. Use all-purpose cleaning spray.
Step 4

Unscrew the drain plug. Use a drive socket #17. Use a ratchet wrench.
Step 5

Drain the used oil.

AUTODOC recommends:
Caution! The oil may be hot.Wait until the oil has completely drained from the drainage hole.
Step 6

Clean the area of the oil pan drainage hole.
Step 7

Screw in the new drainage plug and tighten it. Use a drive socket #17. Use a torque wrench. Tighten it to 39 nm torque.
Step 8

Clean the area of the oil pan drainage hole. Use all-purpose cleaning spray.
Step 9

Unscrew the oil filter. Use the 65/14-F socket. Use a ratchet wrench.
Step 10

Put the old oil filter in the container.

Step 11

Clean the oil filter seat. Use all-purpose cleaning spray.
Step 12

Screw the new filter into its place. Use the 65/14-F socket. Observe the recommended tightening torque.
Step 13

Lower the car.

Step 14

Open the hood.

Step 15

Remove the oil filler cap.
Step 16

Insert the funnel.
Step 17

Pour oil into the engine through the filler. Required amount of oil: 3,6 L.

Replacement: engine oil and filter – HONDA STREAM (RN). Tip:
Use the oil recommended by the manufacturer.
Step 18

Check the oil level using the dipstick. Top up oil if necessary.

Please note!
The oil level should be between the Min and Max marks.
Step 19

Install the oil filler cap.
Step 20

Tighten the oil filler cap.
Step 21

Run the engine for a few minutes. After the oil pressure warning light goes out, stop the engine.

Step 22

Check the oil level 5 minutes after the stop of the engine operation using a dipstick and add oil if necessary.

Please note!
The oil level should be between the Min and Max marks.Make sure that the oil filler cap is properly tightened.Check the threaded plug of the drainage hole and the oil filter seal for tightness. If necessary, carefully tighten them up.
Step 23

Close the hood.

Replacement: engine oil and filter – HONDA STREAM (RN). Tip from AUTODOC experts:
Note that oil pressure warning light, which indicates insufficient pressure in the lubrication system, may be on for a longer time than usual. After a few seconds, the oil will fill all the channels, and the light will go out.To protect the environment from pollution, be sure to dispose of the used filters at special collection points.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the HONDA Stream I (RN) model

Honda Stream 1 tyre size

How to change pollen filter on HONDA Stream I (RN) – replacement guide

Free download PDF
1.63 MB
How to change front brake discs on HONDA STREAM (RN) – replacement guide

Free download PDF
2.2 MB
How to change front anti roll bar links on HONDA STREAM (RN) – replacement guide

Free download PDF
1.19 MB
How to change front strut mount on HONDA STREAM (RN) – replacement guide

Free download PDF
2.36 MB
How to change engine oil and filter on Honda Civic 8 – replacement guide

Free download PDF
2.1 MB
How to replace rear brake pads of disc brake on Honda CR-V III

Free download PDF
1.18 MB

How to change engine oil and filter on HONDA Stream II – replacement guide

Free download PDF
2.38 MB
How to change engine oil and filter on a car – replacement tutorial

Universal

Free download PDF
2.82 MB
How to change engine oil and filter on Honda Civic 8 – replacement guide

Free download PDF
2.1 MB
How to change engine oil and filter on Honda Accord VIII CU – replacement guide

Free download PDF
2.62 MB
How to change engine oil and filter on Honda CR-V II – replacement guide

Free download PDF
2.05 MB
How to change engine oil and filter on Honda Jazz GD – replacement guide

Free download PDF
1.52 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

Top 5 Mistakes to Avoid for Safe Engine Bay Repairs | AUTODOC Tips

8K views

Published on: 04/08/2023
Why does it burn oil? The main cause of oil consumption in EA888 Gen 1

118K views

Published on: 14/08/2025
5 mistakes when replacing consumables

6K views

Published on: 06/02/2025
Transform Your Car's Look: 6 Simple Accessories You Need to Try!

3K views

Published on: 18/11/2021